Kenmore 11064922200 dryer Parts

For the Kenmore 11064922200 dryer, the most reliable “reset” is a simple power reset: unplug the dryer (or switch the breaker off) for 1 minute, restore power, then select a cycle and press PUSH TO START with the door fully closed. See the 11064922200 owner's manual for normal start and restart steps.

• Turn the Cycle Selector (timer) to OFF.
• Unplug the dryer (or turn the breaker off) for 1 minute.
• Restore power.
• Close the door firmly.
• Select a drying cycle and temperature.
• Press PUSH TO START firmly.

The manual’s “will not run” checks cover the most common causes after a reset.

• Confirm the controls are set to an On/running position.
• Make sure the dryer is plugged into a grounded outlet.
• Check the house fuse/breaker (use a time-delay fuse if applicable).
• Close the door tightly; opening the door stops the dryer.
• Press PUSH TO START again after re-closing the door.

A power reset clears a “stuck” control state and forces a clean restart, but it will not bypass normal safety circuits (door switch, overheating protection, and power supply). If the dryer will not run after these checks, a failed door switch is a common no-start cause on many Kenmore dryers.

Last updated: January 2026

A PF (power failure) code on your Kenmore dryer model 11064922200 means the dryer’s cycle was interrupted by a loss of power. Restore power, then restart the cycle using the Start control, or clear the display and reselect your cycle using the steps in the 11064922200 owner's manual.

• Make sure the dryer is plugged into a grounded outlet.
• Check your home breaker or fuse; reset the breaker or replace the fuse if needed.
• Close the dryer door fully (the dryer will not run with the door open).
• Re-select your drying cycle and temperature.
• Press and hold Start (or press Start firmly, depending on your control style) to restart.

Repeated PF codes usually point to an unstable power supply or a loose connection.

• Try a different cycle to confirm the controls respond normally.
• Avoid using an extension cord; plug the dryer directly into the wall outlet.
• Check that the power cord strain relief and terminal block cover are secure (power must be disconnected first).
• If the dryer loses power when you start it, have the outlet and circuit checked.

A PF code is usually not a failed dryer part; it is the dryer telling you the cycle stopped unexpectedly. Fixing the power interruption helps prevent incomplete drying, repeated restarts, and nuisance shutdowns.

Last updated: January 2026

On Kenmore dryer model 11064922200, the correct “dryer fuse” is identified by model match and mounting style, not by a universal physical size. Thermal fuses and thermal cut-offs vary by bracket, terminal layout, and temperature rating; use the 11064922200 owner's manual to confirm the exact part location and access steps.

Customers commonly mean one of these heat-safety parts:

• Thermal fuse: one-time safety device that opens if the dryer overheats
• Thermal cut-off: another one-time overheat device, often replaced as a kit
• High-limit thermostat: temperature limiter that can cycle, but can also fail

Focus on fit and rating, not length or width:

• Match the mounting holes and bracket shape
• Match the wire terminal type and orientation (spade terminals are common)
• Confirm the installation location (many Kenmore 110-style dryers place safety devices on the blower housing or heater housing)
• If a fuse is open, correct airflow restrictions first (lint, crushed vent, blocked hood)
• Always unplug the dryer before testing or replacing parts

If you are troubleshooting an overheat or no-heat condition, these parts are commonly inspected together:

A fuse that “looks the same size” can have a different temperature rating or mounting pattern. Using the correct Kenmore 11064922200-MATCHED part prevents repeat failures, protects the heater circuit, and helps restore safe drying performance.

Last updated: January 2026