Kenmore 11064922200 dryer Parts

For the Kenmore 11064922200 dryer, the most reliable “reset” is a simple power reset: unplug the dryer (or switch the breaker off) for 1 minute, restore power, then select a cycle and press PUSH TO START with the door fully closed. See the 11064922200 owner's manual for normal start and restart steps.

Quick reset steps (power reset)

• Turn the Cycle Selector (timer) to OFF.
• Unplug the dryer (or turn the breaker off) for 1 minute.
• Restore power.
• Close the door firmly.
• Select a drying cycle and temperature.
• Press PUSH TO START firmly.

If it still will not start

The manual’s “will not run” checks cover the most common causes after a reset.

• Confirm the controls are set to an On/running position.
• Make sure the dryer is plugged into a grounded outlet.
• Check the house fuse/breaker (use a time-delay fuse if applicable).
• Close the door tightly; opening the door stops the dryer.
• Press PUSH TO START again after re-closing the door.

Common symptom vs. likely cause

What you notice	What to check next
Nothing happens at all	Power supply, breaker/fuse, cord connection
Drum light works but dryer will not run	Door fully closed, cycle not set to OFF, PUSH TO START pressed
Starts then stops quickly	Venting restriction, overheating protection, cycle setting

Why it matters

A power reset clears a “stuck” control state and forces a clean restart, but it will not bypass normal safety circuits (door switch, overheating protection, and power supply). If the dryer will not run after these checks, a failed door switch is a common no-start cause on many Kenmore dryers.

Last updated: January 2026

A PF (power failure) code on your Kenmore dryer model 11064922200 means the dryer’s cycle was interrupted by a loss of power. Restore power, then restart the cycle using the Start control, or clear the display and reselect your cycle using the steps in the 11064922200 owner's manual.

Quick fix steps

• Make sure the dryer is plugged into a grounded outlet.
• Check your home breaker or fuse; reset the breaker or replace the fuse if needed.
• Close the dryer door fully (the dryer will not run with the door open).
• Re-select your drying cycle and temperature.
• Press and hold Start (or press Start firmly, depending on your control style) to restart.

If PF keeps coming back

Repeated PF codes usually point to an unstable power supply or a loose connection.

• Try a different cycle to confirm the controls respond normally.
• Avoid using an extension cord; plug the dryer directly into the wall outlet.
• Check that the power cord strain relief and terminal block cover are secure (power must be disconnected first).
• If the dryer loses power when you start it, have the outlet and circuit checked.

What to check first (fast troubleshooting)

What you notice	Most likely cause	What we recommend
PF appears after a storm or outage	Brief power interruption	Restart the cycle and monitor
PF appears when you press Start	Weak breaker, loose cord connection	Check breaker, outlet, and cord connections
Dryer will not start after PF	Door not closed, controls not set to On	Verify door closure and cycle settings
PF repeats randomly mid-cycle	Intermittent power drop	Have the circuit/outlet inspected

Why it matters

A PF code is usually not a failed dryer part; it is the dryer telling you the cycle stopped unexpectedly. Fixing the power interruption helps prevent incomplete drying, repeated restarts, and nuisance shutdowns.

Last updated: January 2026

On Kenmore dryer model 11064922200, the correct “dryer fuse” is identified by model match and mounting style, not by a universal physical size. Thermal fuses and thermal cut-offs vary by bracket, terminal layout, and temperature rating; use the 11064922200 owner's manual to confirm the exact part location and access steps.

What “dryer fuse” usually refers to

Customers commonly mean one of these heat-safety parts:

• Thermal fuse: one-time safety device that opens if the dryer overheats
• Thermal cut-off: another one-time overheat device, often replaced as a kit
• High-limit thermostat: temperature limiter that can cycle, but can also fail

How we recommend confirming the correct fuse

Focus on fit and rating, not length or width:

• Match the mounting holes and bracket shape
• Match the wire terminal type and orientation (spade terminals are common)
• Confirm the installation location (many Kenmore 110-style dryers place safety devices on the blower housing or heater housing)
• If a fuse is open, correct airflow restrictions first (lint, crushed vent, blocked hood)
• Always unplug the dryer before testing or replacing parts

Related parts that are often checked for overheating

If you are troubleshooting an overheat or no-heat condition, these parts are commonly inspected together:

Part type	What it does	Example part for this model page
Thermal cut-off kit	Opens on extreme heat; often replaced as a set	Dryer thermal cut-off fuse kit 279816
High-limit thermostat	Limits heater temperature	Dryer high-limit thermostat WP3977767
Operating thermostat	Regulates normal cycling temperature	Dryer operating thermostat WP3387134

Why it matters

A fuse that “looks the same size” can have a different temperature rating or mounting pattern. Using the correct Kenmore 11064922200-MATCHED part prevents repeat failures, protects the heater circuit, and helps restore safe drying performance.

Last updated: January 2026