Kenmore 11060702990 electric dryer Parts

The Kenmore electric dryer model 11060702990 is a 29-inch wide dryer. For the exact overall cabinet height and depth (which can vary by venting setup and leveling legs), we recommend confirming the measurements in the 11060702990 owner's manual.

What “29-inch wide” means

This is the standard cabinet width class used for fit and clearance planning.

• Measure the opening width at the narrowest point (trim can reduce clearance)
• Allow extra space for the power cord and vent connection behind the dryer
• Plan for the door swing and room to pull out the lint screen
• Keep the dryer level; leveling legs can slightly change overall height

How to measure your dryer correctly

Use a tape measure and record three dimensions.

Measurement	Where to measure	Tip
Width	Left side to right side of cabinet	Confirm it matches the 29-inch class
Height	Floor to top of cabinet	Measure with the dryer level
Depth	Front of cabinet to back	Add space for vent and cord

Why it matters

Correct sizing prevents installation problems like a crushed or kinked vent, poor airflow, and difficulty servicing parts such as the heating system or drum drive.

If you are troubleshooting heat or long dry times while planning a reinstall, common related parts for this model include the dryer element 279838 and the cut-off kit 279816.

Last updated: February 2026

To hard reset your Kenmore electric dryer model 11060702990, unplug the power cord (or switch the breaker off) for at least 1 minute, then restore power and start a cycle normally. This clears many temporary control and cycle issues and is the safest first step.

Hard reset steps (recommended)

• Turn the Cycle selector (timer) to OFF.
• Unplug the dryer from the outlet (or turn the dryer breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door, select a cycle, then press PUSH TO START.

For model-specific operating steps and cycle details, follow the 11060702990 owner's manual.

If it still will not start after the reset

A reset will not fix a failed safety device or a door circuit problem. On this model, the dryer stops when the door opens and will not run again until the door is closed and you press PUSH TO START.

Check these common causes:

• Door not fully closed or latch not engaging
• Failed door switch (a frequent no-start cause)
• Blown thermal cut-off due to restricted venting or overheating
• Timer contacts worn (mechanical timer models)
• Power supply issue (tripped breaker, loose cord connection)

Helpful model-matched parts to consider during diagnosis:

• Dryer door switch WP3406107
• Cut-off kit 279816

Quick troubleshooting table

Symptom after reset	Most likely area to check	What to do next
Nothing happens when you press Start	Door circuit, power	Confirm door closes firmly; verify breaker is on
Runs but no heat	Heating circuit, airflow	Clean venting; inspect heater and thermostats
Stops mid-cycle	Overheat protection, vent restriction	Clean lint screen and exhaust ducting

Why it matters

A hard reset clears temporary cycle or control confusion, but dryers also have built-in safety circuits (door switch and overheat protection) that intentionally prevent operation when conditions are unsafe. Cleaning lint and ensuring good airflow helps prevent repeat shutdowns.

Last updated: February 2026

For Kenmore electric dryer model 11060702990, we remove the front panel by disconnecting power, opening up the top, removing the mounting screws, then lifting the front panel off while supporting the drum and disconnecting any wiring (such as the door switch) as needed. Use the 11060702990 owner's manual for the exact screw locations.

Safety first

• Unplug the dryer (or switch off the breaker) before starting.
• If the dryer is hard-wired, shut off power at the panel before touching any wiring.
• Wear cut-resistant gloves; cabinet edges can be sharp.
• Do not pull the front panel away until you are ready to support the drum.
• Take a photo of wire connections before disconnecting anything.

Step-by-step: removing the front panel

1. Disconnect power and pull the dryer forward enough to work safely.
2. Release the top: slide a putty knife under the front edge of the top (near the left and right corners) to release the spring clips, then lift the top up.
3. Remove front panel screws: remove the screws along the top edge of the front panel (inside the cabinet, just under the raised top). Some versions also use screws inside the door opening.
4. Disconnect the door switch: unplug the harness from the dryer door switch WP3406107 if it is mounted to the front panel.
5. Lift the front panel off: tilt the panel forward slightly, then lift it up and off the lower retaining tabs.

What to expect once the panel is off

What you see	What it means	Common next step
Belt around drum	Normal drive setup	Inspect belt wear and routing
Loose belt or belt dust	Belt slipping or broken	Replace the belt
Lint buildup in cabinet	Airflow restriction risk	Vacuum cabinet and vent path

Why it matters

Removing the front panel is the main access step for common repairs on this Kenmore dryer, including replacing a broken belt, checking the idler pulley, or servicing the heating system. If you are chasing a no-heat complaint, the manual’s troubleshooting section is also a good next stop.

Last updated: February 2026

A Kenmore electric dryer typically lasts 10 to 13 years. With consistent care on your Kenmore model 11060702990, it’s common to reach the high end of that range because airflow, heat control, and drive components stay under less strain when the dryer is kept clean and properly vented (see the 11060702990 owner's manual).

Typical lifespan and what affects it

Most dryer failures that shorten life come from restricted airflow (overheating) or worn moving parts.

• Clean the lint screen every load and keep the exhaust vent clear
• Avoid overloading; heavy loads strain the motor, belt, and drum support
• Use the right cycle and heat setting to reduce overdrying and heat stress
• Keep the dryer level to reduce vibration and bearing wear
• Address new noises early (squeal, thump, scraping) before parts fail

Maintenance schedule we recommend

The manual calls out vent and lint buildup as a key maintenance item; lint inside the dryer should be removed periodically by a qualified service person.

Task	How often	Why it helps lifespan
Clean lint screen	Every load	Maintains airflow and drying efficiency
Check and clean venting	Every 3 to 6 months	Prevents overheating and long dry times
Deep clean lint from vent run	At least yearly	Reduces strain on the heating system
Internal lint removal (service)	Every 2 to 3 years	Reduces heat buildup and wear

Parts that commonly wear as dryers age

If your dryer still runs but performance drops, these are frequent wear items on many Kenmore electric dryers:

• Drum belt 341241 (drum won’t turn, squealing, burning rubber smell)
• Dryer operating thermostat WP3387134 (overheating, cycling issues)
• Dryer element 279838 (no heat or weak heat)
• Dryer blower wheel WP694089 (poor airflow, rumbling, longer dry times)

Why it matters

A dryer that maintains strong airflow and stable temperatures dries faster, runs cooler, and puts less stress on the motor, heater, and thermostats. That combination is what most often separates a 10-year dryer from a 15-year dryer.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number plate; on model 11060702990, that plate is typically found in the door opening area. Once you have the full model number, we can match the correct parts, wiring, and operating instructions.

Where to look for the model number plate

Check these common locations on Kenmore electric dryers:

• Inside the dryer door opening (on the cabinet frame)
• On the back panel of the dryer cabinet
• Near the lint screen housing (depending on the design)
• On a metal plate or durable label that also lists the serial number

For the exact reference and how the manual describes it, use the 11060702990 owner's manual.

How to read the number you find

Kenmore model numbers are long on purpose; each section helps identify the platform and parts list.

What you see	What it means	What to do next
Full model number (example: 11060702990)	Identifies the exact dryer design	Use it to select parts and diagrams
Serial number	Identifies the production unit	Keep it for service history
Partial number (missing digits)	Not enough to guarantee correct parts	Re-check the plate for the full string

Why it matters for parts and troubleshooting

Using the complete model number prevents ordering the wrong items and speeds up diagnosis when the dryer will not start, will not heat, or makes noise.

• Heating problems often trace to the heater circuit, such as the dryer element 279838 or a thermal cut-off
• No-start symptoms can involve the door circuit, such as the dryer door switch WP3406107
• Drum not turning commonly points to a worn belt or idler pulley

Last updated: February 2026

If your Kenmore electric dryer model 11060702990 runs but you do not feel heat in the drum after about 5 minutes on a heated cycle, the heating circuit needs attention. A failed heating element is common; confirm it with a continuity test and a quick visual inspection.

Quick heat check (no tools)

Our manual recommends running a full heat cycle (not Air Dry) and checking for heat after 5 minutes. Use this as your first screening step in the 11060702990 owner's manual.

• Select a heated cycle (not AIR DRY)
• Start the dryer and wait 5 minutes
• Open the door and feel for heat inside the drum
• If there is no heat, move to the electrical checks below

Definitive test: multimeter checks

Unplug the dryer (240V) before testing.

• Continuity through the element: a good element typically shows about 10 to 50 ohms
• Short to ground: check from an element terminal to the metal heater housing; it should read OL/infinite
• Burn marks or broken coil: any visible break usually means replacement
• Inspect wiring: look for overheated terminals; repair damaged leads before installing a new element

What the results usually mean

Test result	What it points to	What we do next
No heat, element reads OL (open)	Element coil is broken	Replace the dryer element 279838
Element reads normal ohms, but still no heat	Cut-off, thermostat, wiring, or supply issue	Check thermal cut-off and thermostats
Element shows continuity to metal housing	Element is shorted	Replace the dryer element 279838 and inspect wiring

Related parts that often fail with “no heat”

A “no heat” complaint is not always the element alone. These parts commonly affect heating on this style of Kenmore electric dryer:

• Cut-off kit 279816 (thermal cut-off and high-limit protection)
• Dryer operating thermostat WP3387134
• Dryer thermostat WP3977767 (high-limit thermostat)

Why it matters

A weak or failed heating circuit causes long dry times, damp loads, and unnecessary wear on the motor and drum belt. Confirming the element with a meter prevents replacing the wrong part and helps restore normal cycle performance.

Last updated: February 2026