Kenmore 79046592500 electric range Parts

To reset your Kenmore electric range model 79046592500, we recommend doing a power reset: turn the range off, shut off power at the breaker (or unplug it), wait 1 minute, then restore power and test Bake and surface elements.

Quick reset steps (power cycle)

• Turn all surface knobs to OFF.
• Press STOP/CLEAR once to cancel any active oven function.
• Switch the range circuit breaker OFF (or unplug the power cord).
• Wait 60 seconds.
• Restore power, then set Bake and confirm the PREHEAT light comes on and the oven begins heating.

If the control panel seems “stuck” after a reset

The STOP/CLEAR pad clears most cooking functions, and the range can also have a door lockout or a door lock state after Self-Clean. Use these checks:

• If Self-Clean was running, let the oven cool about 1 hour before trying to open the door.
• Do not force the door open if the door lock is engaged.
• Confirm the DOOR LOCKED light is off before starting a new cycle.
• Re-enter the cooking mode after clearing the display.

When a reset does not fix heating problems

A reset restores normal control operation, but it will not repair a failed component. These are common next checks for an electric range:

Symptom	Most likely area to check	What to do next
Oven will not heat in Bake	Bake heating circuit	Inspect/replace the frigidaire range bake element 318255401 if it is damaged or not heating
Oven temperature is inaccurate	Temperature sensing	Test/replace the frigidaire range oven temperature sensor 316217002
No power or intermittent power	Power connection	Inspect wiring and connections at the terminal block (power off first)

Why it matters

Resetting clears a “hung” control state (for example after a canceled cycle or keypad input issue) and is the fastest safe first step before testing parts like the bake element, temperature sensor, or power connection.

For model-specific keypad functions and indicators (including STOP/CLEAR, PREHEAT, and DOOR LOCKED), follow the 79046592500 owner’s manual.

Last updated: February 2026

On the Kenmore 79046592500 electric range, an oven that “stops working” is usually caused by a power supply problem, a failed heating circuit (bake or broil element), or a control fault such as an error code (F1, F3, F9) that stops operation until cleared. See the 79046592500 owner's manual for model-specific checks.

Quick checks we recommend first

• Confirm the range has power (check the house breaker for a trip and reset if needed).
• Press STOP/CLEAR to cancel a stuck cycle or clear a fault condition.
• If the display shows F1, F3, or F9, record the code, clear it, and retest.
• Set BAKE 350°F and look for the lower element to glow red after preheat starts.
• Set BROIL and look for the upper element to glow red.
• If the oven was in Self-Clean, wait for the door to fully unlock before testing bake/broil.

Most common causes (and what they look like)

Symptom	Likely cause	What to do next
No heat in bake, broil works	Bake element failed	Inspect for blisters/breaks; consider replacing the frigidaire range bake element 318255401
No heat in broil, bake works	Broil element failed	Inspect broil element for damage; replace if open
Oven heats poorly or temps swing	Temperature sensor out of range	Check sensor wiring and resistance; consider the frigidaire range oven temperature sensor 316217002
Beeping with F1/F3/F9	Electronic control detected a fault	Clear with STOP/CLEAR; if it returns, service the control circuit

Why it matters

When an element or sensor fails, the control can stop heating to prevent overheating or unsafe operation. Catching the symptom early helps avoid repeated shutdowns, error beeps, and uneven baking.

Safety notes before troubleshooting

• Turn power off at the breaker before inspecting wiring or removing panels.
• Do not touch heating elements; they can stay hot long after the oven is turned off.
• Do not attempt to operate the oven during a power failure.

Last updated: February 2026

On the Kenmore electric range model 79046592500, the model and serial number are printed on the serial plate on the oven front frame behind the oven door; on some versions, the plate is behind the storage drawer. The exact location is shown in the 79046592500 owner's manual.

Where to look on model 79046592500

Check these common label locations in this order:

• Open the oven door and look along the front frame (the face frame around the oven opening).
• Look behind the oven door at the front frame area where the serial plate is mounted.
• If you have a storage drawer, pull it out and check behind the drawer (some models place the plate there).
• Write down the model number, serial number, and any lot number/letter shown on the plate.

What to record (and why it matters)

Having the full model and serial information helps us match the correct Kenmore range parts (like a bake element, surface element, or control overlay) and avoid ordering a similar-looking part that will not fit.

What you’ll see	Example format	Why we need it
Model number	790.4659…	Identifies the correct design family
Serial number	Letters and numbers	Helps match production changes
Lot number/letter	Letter or code	Helps confirm exact revision

Tips for reading the label

• Use a flashlight; the plate is often in a shadowed area.
• Copy the characters exactly (including leading zeros).
• If the plate is behind the drawer, remove the drawer fully for a clear view (steps are typically shown in the installation guide).

Why it matters

Kenmore 790-series ranges can have different cooktop and oven configurations; the correct model number ensures we pull the right diagrams and compatible parts the first time.

Last updated: February 2026

If our Kenmore electric range model 79046592500 oven is not getting hot, the most common causes are a failed bake element, a bad oven temperature sensor, or a control or wiring problem. Start with a preheat test and a quick visual inspection of the heating elements.

Quick checks we recommend first

• Confirm the oven is actually preheating (give it 10 to 15 minutes).
• Look for the lower bake element glowing red during preheat; it should cycle on and off.
• Make sure the oven door is fully closed.
• If you recently installed the range or moved it, verify the power connection and that all controls are OFF per the installation guide.
• If the oven heats but food still seems underdone, review preheat and rack position tips in the 79046592500 owner’s manual.

Most likely failed parts (and what they cause)

Symptom	Most likely cause	What you’ll usually notice
No heat in Bake, Broil works	Bake element issue	Lower element looks blistered, cracked, or never warms
Oven heats but won’t reach temp or swings widely	Temperature sensor issue	Long preheat times, uneven baking
No heat in Bake and Broil	Control, wiring, or power supply issue	Display works but elements never energize

Parts to consider for model 79046592500

• Frigidaire range bake element 318255401: restores bake heat when the lower element is open or damaged.
• Frigidaire range oven temperature sensor 316217002: restores accurate temperature sensing when the sensor is out of range.

Safe troubleshooting steps

1. Turn off power at the breaker before any inspection or testing.
2. Inspect the bake element for cracks, holes, or burn spots.
3. If you have a multimeter, check the bake element and sensor for continuity (replace the part if it tests open).
4. If both test good, inspect wiring connections at the element, sensor, and control for heat damage or loose terminals.

Why it matters

An oven that will not heat is usually a simple electrical failure (element or sensor). Fixing the root cause restores proper preheat, stable temperatures, and prevents extended cook times that can dry out food.

Last updated: February 2026