kenmore-903136-9010-Range Surface Element Control Switch Kit
Hover to Zoom

Range Surface Element Control Switch Kit 903136-9010


Part #903136-9010

Online price
In Stock
For ZIP codes near Edit
365-day return policy
This part fits
Kenmore, Kenmore Elite, Frigidaire

Part Information

Surface element control switch kit 903136-9010 is an original equipment manufacturer (OEM) part that fits some Kenmore, Kenmore Elite and Frigidaire electric ranges.

Surface element control switch kit 903136-9010 replaces the switch that turns the surface element on and off and controls how much heat the element produces.

This kit includes the surface element control switch, bushing/spacer, screws and instruction sheet.

Replaces original electric range surface element control switch part numbers 318220020, 318220080 and 318369615.

Fits some electric ranges in these series: Kenmore and Kenmore Elite 790; and Frigidaire BFES, CFES, CGLES, CPES, DGES, FED, FES, GLED, GLES and PLES.


1-8 of 12 reviews
Handy Sandy
Dearborn, MIReviews 1Votes 0
• 2 years ago
Handy Sandy• 2 years ago
Relatively Easy to Install

I was able to find the part number in the Instruction manual that came with my stove with ease. Ordering online was a cinch and it was relatively easy to install. The part looked different than the one I was replacing. Once I figured out the wire numbering/coding system, the part was very easy to install.

Retired woman
ColoradoReviews 1Votes 0
• 2 years ago
Retired woman• 2 years ago
Installing 2 burner switches

Very simple. The YouTube showed how to do, particularly how to transfer the electrical connections.
It took about 45 min to install 2 of them. The only difficult part was to determine which direction to place them, so I got them turned 180 degrees at first. It was simple to fix that.

Johnny rotten
Hampstead, NCReviews 1Votes 0
• 3 years ago
Johnny rotten• 3 years ago
Timely and easy installation

Replaced 6” burner switch with ease! Just removed old one and used screws provided to install new one, reconnected wires.

Albany gaReviews 1Votes 0
• 3 years ago
Rhinods• 3 years ago
Easy installation

installation was super easy with the diagram that is on your site!

SeattleReviews 1Votes 0
• 4 months ago
Percebes• 4 months ago
Works great but a different size than original

The switch that had gone bad in my range was a slightly smaller than this replacement. Despite the size difference this new switch fits but requires the use of a spacer that is included. Without the spacer the stem on this switch will be higher than the other 3 original switches. The new switch also has different names for each terminal than the old switch. I found directions online which explained which wire went to which terminal on the new switch. It would've been nice if this info had been included with the new switch. Otherwise it was easy to connect and works great.

San Diego, CAReviews 1Votes 0
• 7 months ago
PapaDragonheart• 7 months ago
Wasn't an exact replacement, but did the trick!

2 of our burner dials weren't operating properly. A few youtube videos to figure out how to expose everything, take some detailed pictures of the wiring before you undo. The new configuration matched the letters, but not the shape/order.

Research needed
Burner controlReviews 2Votes 0
• 7 months ago
Research needed• 7 months ago
Easy once you get to the switch and mark the wires

Different design but works good. Must mark wires prior to removing them from the old switch. Then connect those same marked wires to the new switch corresponding locations that are also marked. I do advise before starting, that you attach the knob to the new switch to know which way it is pointing in the off position

Capt. Doc
Kailua Kona, HawaiiReviews 1Votes 0
• 2 years ago
Capt. Doc• 2 years ago
Print was very small and hard to read on product.

Replace two Range Surface Element Switches. Not as easy as video showed. Prefer printed instructions especially when part numbers change and size and layout of part terminals change.

1-8 of 12 reviews