Kenmore 11079522800 dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label on the appliance. On Kenmore model 11079522800, you’ll typically find that label in the door opening (door well) or on the cabinet, and it lists both the model number and serial number.

Where to look on the dryer

Check these common label locations first:

• Inside the dryer door opening on the cabinet frame (door well)
• Along the inside edge of the door opening near the top
• On the back of the dryer cabinet near the top
• On the side panel near the door opening (less common)

For the exact label location and how it’s referenced in the documentation, use the 11079522800 owner’s manual.

What to write down (and why)

Record the information exactly as shown on the label:

• Model number (example format: 110.79522800 or 11079522800)
• Serial number (needed to identify production range)
• Purchase date (helpful for service history)

Why it matters

The model number is what we use to match the correct Kenmore dryer parts and diagrams. The serial number helps narrow down version changes so you get the right replacement part the first time.

Quick ID checklist

Use this table to confirm you’re reading the right tag.

Item on label	What it’s used for	Example you might see
Model number	Parts lookup and diagrams	11079522800
Serial number	Version and production info	M12345678
Gas type or ratings (if listed)	Installation and setup checks	Natural gas, BTU rating

Tip for gas dryers

If your dryer is gas, the rating plate in the door well can also list burner information (useful for confirming the gas type during installation). For setup requirements and safety notes, follow the 11079522800 installation guide.

Last updated: February 2026

To hard reset your Kenmore dryer model 11079522800, unplug it (or switch off the breaker) for 1 to 5 minutes, then restore power and try starting a cycle again. This clears many temporary control and cycle issues and is the first step we recommend before replacing parts.

Hard reset steps (works for most Kenmore dryers)

• Turn the dryer OFF.
• Unplug the power cord (or turn the breaker OFF).
• Wait 1 to 5 minutes.
• Plug back in (or turn the breaker ON).
• Close the door, select a cycle, then press Start.
• If the dryer still will not start, follow the “will not start” checks in the 11079522800 owner's manual.

If it still will not start after the reset

The installation instructions for this model call out a few quick checks that often solve a “dead” or “won’t start” complaint.

• Confirm the dryer is plugged into a grounded 3-prong outlet (no adapter, no extension cord).
• Make sure the door is fully closed; a failed door switch can prevent starting.
• Try a Timed Dry heated cycle (avoid “Air Only” when you are testing for heat and run operation).
• Check airflow basics: clean the lint screen and make sure the vent is not crushed or blocked.
• If the drum light works but the motor will not run, test common start-interlock parts.

Common parts related to “won’t start” symptoms

Symptom after reset	Most common check	Example part for this model
Nothing happens when you press Start	Door not sensed closed	Dryer door switch WP3406107
Clicks/hums but drum will not turn	Belt or idler issue	Dryer drum belt 341241
Start button feels normal but won’t engage	Start switch issue	Dryer push-to-start switch WP3977456

Why it matters

A hard reset restores normal operation when the timer or controls get “stuck,” but it also helps you avoid replacing good parts. If the dryer fails the same way immediately after a reset, the problem is usually a switch, drive component, or power/airflow issue.

Last updated: February 2026

For Kenmore dryer model 11079522800, the cabinet size is about 43 3/8 in. high, 29 in. wide, and 27 in. deep (depth varies slightly by door style). These dimensions come from the model’s installation measurements in the installation guide.

Dimensions at a glance

Here are the key measurements you will plan around for delivery, fit, and venting:

• Width: 29 in. (73.7 cm)
• Height: 43 3/8 in. (about 1102 mm)
• Depth: about 27 in. (about 705 mm)
• Door clearance: allow room for the door to open fully
• Rear clearance for venting: most installs need at least 5 in. behind the dryer for the exhaust vent and elbow

Door style can change the depth

The installation measurements show multiple door options (small/large/wide opening and hamper-style doors). That means the front projection can differ, even though the cabinet footprint is essentially the same.

What you’re measuring	What to use	Why
Space in a laundry alcove	29 in. W x 43 3/8 in. H	Matches the dryer cabinet
Depth to the front of the door	Plan around ~27 in. plus door swing	Door style affects how far it sticks out
Total depth including vent	Add 5 in. minimum behind dryer	Room for exhaust elbow

Why it matters

Correct sizing prevents crushed venting, noisy vibration from tight side clearances, and door interference. It also helps you avoid overheating issues caused by restricted airflow.

Quick measuring tips we use

• Measure the opening width at the narrowest point (baseboards and trim count).
• Measure floor to the lowest overhead obstruction (shelves, cabinets, pipes).
• Measure back wall to the front edge of where the dryer will sit, then add vent space.
• If installing in a closet, plan for required door ventilation openings.

Last updated: February 2026