Kenmore 11082826102 electric dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label; on model 11082826102, that label is located at the top inside the dryer door well. Once you have the full model number, you can match the correct parts, wiring, and troubleshooting steps.

Where to look on Kenmore model 11082826102

Check these common label locations in this order:

• Top inside the dryer door well (most common for this model)
• Inside the door opening around the frame
• On the back panel of the cabinet
• Near the lint screen housing (some designs place labels nearby)

Use the location diagram and product record section in the 11082826102 owner's manual to confirm the exact label placement and how the model and serial number are formatted.

What the model number looks like (and why it matters)

Kenmore model numbers are typically a long string of digits. Many Kenmore dryers also start with a prefix such as 110. (a common Kenmore manufacturing prefix). Record the entire model number exactly as shown.

Why it matters

The model number determines which parts fit and which procedures apply, especially for items like the heating circuit and temperature sensing.

What you’re doing	Why the model number is required
Ordering replacement parts	Ensures correct fit for the drum, heater, motor, and sensors
Looking up wiring/diagnostics	Matches the correct electrical design and component layout
Checking cycle features	Confirms control type and options for Auto Dry vs. Timed Dry

Tips for writing it down correctly

• Copy every digit in order; do not shorten it.
• Record the serial number too; it helps when scheduling service.
• Take a clear photo of the label before it fades or gets scratched.

Last updated: February 2026

On the Kenmore electric dryer model 11082826102, the control panel (console) typically opens by removing the rear console screws, sliding the console slightly, then lifting it off so you can access the control bracket and wiring. Follow the screw locations and console handling notes in the 11082826102 owner's manual.

Before you start (safety and prep)

• Unplug the dryer (or switch off the breaker) before opening the console.
• Work from the back of the console when possible; most fasteners are there.
• Support the console as you lift it so you do not strain the wire harness.
• Keep screws grouped by location so reassembly is straightforward.
• If the dryer is stacked or tight to a wall, pull it forward enough to work safely.

Steps to open the control panel (common Kenmore 110-style console)

1. Disconnect power.
2. Move to the back of the console and remove the screws securing the console to the top or rear panel (often 1/4-inch hex-head screws).
3. Slide the console back slightly (about 1 inch is common) to release tabs.
4. Lift the rear of the console up, then lift it off and set it aside.
5. If you need deeper access, remove the screws holding the control bracket/control board mounting and carefully position the assembly without pulling on wires.

What you will see once it is open

Area	What it does	What to watch for
Timer/control board area	Runs cycles and options	Do not pull on connectors; release locking tabs first
Harness connectors	Carries power/signals	Take a photo before unplugging anything
Console tabs/clips	Holds console to top	Avoid prying hard; tabs can crack

Why it matters

Opening the console the right way prevents broken mounting tabs, pinched wiring, and loose connections that can cause no-start symptoms or intermittent operation.

Last updated: February 2026

Common problems on a Kenmore electric dryer like model 11082826102 include no heat, long dry times, the drum not turning, and loud squealing or thumping. Most issues trace back to airflow restrictions (lint buildup or poor venting) or normal wear of drive and heating components.

Most common symptoms and what usually causes them

• Dryer runs but no heat: tripped breaker (often one of two), failed heating circuit parts, or a blown thermal cut-off from overheating.
• Long drying times: clogged lint screen, crushed or kinked vent, blocked exhaust hood, or a failing blower wheel.
• Drum will not turn: worn idler pulley, worn drum rollers, or a failing drive motor.
• Loud noise (squeal, rumble, thump): worn drum support rollers, idler pulley, or drum seal.
• Burning smell: lint accumulation in the cabinet or venting; a brief “new heat” odor can also happen after first heating.

Quick checks we recommend first (fast, high-impact)

1. Clean the lint screen every load and wash it periodically if you use dryer sheets.
2. Verify power: many electric dryers need two fuses/breakers; the dryer can run but not heat if one trips.
3. Inspect venting: use heavy metal venting, avoid plastic or foil; fully extend flexible metal vent and remove excess to prevent sagging.
4. Check the outside exhaust hood: make sure it opens freely and is not packed with lint.

Parts that commonly fix these problems on 11082826102

Symptom	Common part to check/replace	Example part for this model
No heat	Heating element	Dryer heating element WP3387747
No heat or overheating shutdown	Thermal cut-off kit	Dryer thermal cut-off fuse kit 279973
Squealing/rumbling, drum drag	Drum rollers	Support WPW10314173
Drum not turning, squeal	Idler pulley	Dryer idler pulley 279640

Why it matters

Good airflow prevents overheating, protects the heating system, and shortens dry times. The manual also warns that improper venting can cause moisture and lint to collect indoors, creating performance and indoor air quality problems.

For model-specific cleaning, venting, and troubleshooting steps, follow the 11082826102 owner's manual.

Last updated: February 2026

The Kenmore electric dryer model 11082826102 is a standard 27-inch class dryer. The installation diagram in the 11082826102 owner's manual shows a 27 in. width and a 38 in. minimum height for undercounter installations; plan extra space behind the dryer for the vent elbow.

Key dimensions and clearances to plan for

Use these sizing points when measuring your laundry area:

• Width: 27 in.
• Undercounter height (minimum): 38 in.
• Recommended side clearance: about 1 in. on each side (helps reduce noise transfer)
• Behind-dryer clearance (minimum): 5 1/2 in. for the exhaust vent with elbow
• Floor requirements: level within 1 in. slope under the entire dryer

Quick sizing table

Measurement	What to plan for	Notes
Dryer width	27 in.	Standard footprint for this model
Minimum undercounter height	38 in.	For custom undercounter installs
Space behind dryer	5 1/2 in. minimum	Allows vent elbow clearance
Side spacing	1 in. recommended	Helps reduce vibration and noise

Why it matters

Correct sizing prevents crushed venting, overheating from restricted airflow, and installation headaches. Leaving the proper rear clearance also makes it easier to service common wear items like the belt, drum rollers, and idler pulley.

Measuring tips we use

• Measure the opening width at the front and back (walls are not always square).
• Measure height to the lowest obstruction (countertop lip, shelf, or trim).
• Include the vent connection path and elbow depth in your rear clearance.
• Confirm the dryer sits level so sensor cycles tumble and dry correctly.

Last updated: February 2026