Kenmore 11068842700 dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label; on Kenmore model 11068842700, that label is located at the top inside the dryer door well. Once you have the full model number, you can match the correct parts, wiring, and installation requirements.

Where to look on the dryer

Check these common label locations first (start with the door opening):

• Top inside the dryer door well (most common on Kenmore 110-series dryers)
• Inside the door opening on the cabinet frame
• Back panel (less common, but possible)
• Near the lint screen housing (some designs place the label nearby)

For the exact label location and how the model and serial number are formatted, use the 11068842700 owner's manual.

How to read the number (and why it matters)

Kenmore model numbers often start with a prefix that helps identify the manufacturing source and parts family. For example, a 110 prefix is commonly associated with Whirlpool-built Kenmore dryers, which is why parts like a heating element, door switch, or drum support roller must match the full model.

Why it matters

Using the complete model number helps us:

• Pull the correct parts diagram and part list
• Match electrical and venting requirements to your exact dryer
• Avoid ordering look-alike parts that do not fit
• Confirm compatible maintenance and troubleshooting steps

Quick checklist before you order parts

Use this checklist to avoid mix-ups:

• Write down the full model number exactly as shown (all digits)
• Record the serial number too (helps with production variation)
• Compare the model number on the label to what’s on any paperwork
• If replacing a wear item, match it to the model-specific part listing

Common parts that depend on the exact model

Symptom	Often involved part	Example for this model
Dryer will not start	Door switch	Dryer door switch WP3406107
Loud rumbling or thumping	Drum support roller	Support WPW10314173
No heat or weak heat	Heating element	Dryer heating element WP3387747

If the label is hard to read

If the label is faded, gently wipe it with a damp cloth and read it under bright light. Avoid solvents; they can remove the remaining print.

Last updated: February 2026

For Kenmore dryer model 11068842700, we replace the thermistor by disconnecting power, accessing the blower housing or exhaust duct area, swapping the sensor and reconnecting the wires exactly as found. Use the 11068842700 owner's manual for safety notes and panel handling.

Before you start (safety and prep)

• Unplug the dryer (or switch off the breaker) before servicing.
• Let the dryer cool completely if it was recently running.
• Take a quick photo of wire positions before you disconnect anything.
• Work with the dryer pulled out far enough to avoid crushing or kinking the vent.
• Keep screws organized by panel so reassembly is straightforward.

Replacement steps (typical for this Kenmore platform)

1. Disconnect power.
2. Remove the rear panel (or the lower access panel, depending on your configuration).
3. Locate the thermistor on or near the blower housing or exhaust duct.
4. Disconnect the wire connector from the thermistor.
5. Remove the mounting screw(s) and take out the old thermistor.
6. Install the new thermistor, secure it, and reconnect the wiring.
7. Reinstall panels, restore power, and run a timed heat cycle to confirm normal heating.

What part is involved?

On this model, the thermistor is commonly replaced as the dryer thermistor. If you are sourcing the part for 11068842700, match by model number and wiring connector style.

Symptom	What it often points to	What to check next
Runs but heat is erratic	Thermistor out of range	Thermistor, wiring, venting
Stops early on auto cycles	Moisture/temperature sensing issue	Thermistor and moisture sensor
Overheats or shuts down	Airflow restriction or safety trip	Lint screen, ducting, thermal cut-off

Why it matters

The thermistor helps the dryer regulate temperature. A failing thermistor can cause long dry times, overheating, or cycles that end too soon, even when the heating element is still good.

Last updated: February 2026

The average lifespan of the Kenmore 11068842700 dryer is about 13 years with normal household use. Regular vent cleaning, lint removal, and timely replacement of wear parts (belt, rollers, idler) are what most often determine whether it reaches or exceeds that average.

What affects lifespan the most

• Venting and airflow: restricted exhaust overheats components and shortens life.
• Lint control: lint buildup stresses the blower housing, heater area, and thermostats.
• Load size: frequent overloading strains the drive motor and drum support system.
• Heat settings: consistently running high heat can accelerate wear on heating and cycling parts.
• Maintenance and repairs: replacing common wear items early prevents bigger failures.

Maintenance checklist (best return for the effort)

Use the schedule in your owner's manual as your baseline.

• Clean the lint screen before every load.
• Check airflow at the outside hood; it should be strong and steady.
• Keep the vent path as short and straight as possible; clean it regularly.
• Avoid crushing or kinking the vent when pushing the dryer back.
• Listen for squealing or thumping; address it before it damages the drum or motor.

Common wear items and what they usually mean

Symptom	Most common cause	Example part for this model
Squealing, chirping	Worn idler or drum support components	Dryer idler pulley 279640
Long dry times, overheating	Poor airflow or heat system issue	Dryer heating element WP3387747
Thumping, rubbing	Drum seal or drum support wear	Dryer drum seal 280114

Why it matters

A dryer that is vented correctly and kept clear of lint runs cooler and with less strain; that directly extends the life of the heating system, drive motor, and drum support parts. The installation requirements for safe, cleanable venting are outlined in the installation guide.

Last updated: March 2026