Kenmore 11092826101 gas dryer Parts

On Kenmore gas dryer model 11092826101, a blown thermal fuse commonly shows up as a dryer that will not run at all, or a dryer that runs but has heat problems after an airflow restriction. The sure way to know is a continuity test on the fuse with the dryer unplugged (no continuity means the fuse is blown). See the 11092826101 owner’s manual for access and safety notes.

• Dryer will not start (no motor run) even though power is present
• Dryer starts but shuts off unexpectedly during a cycle
• Long dry times and very hot cabinet (often points to restricted venting)
• Burning smell or unusually hot exhaust (stop using the dryer and inspect venting)
• Recent vent kink, crushed duct, or clogged outside hood (common root cause)

1. Unplug the dryer from the grounded outlet.
2. Access the blower housing area where the thermal fuse is typically mounted.
3. Remove at least one wire from the fuse terminal.
4. Set a multimeter to continuity or lowest ohms.
5. Test across the fuse terminals.

Expected meter result

If you need the correct replacement for this model, use the dryer thermal fuse WP3390719.

The thermal fuse is a one-time safety device. When airflow is restricted, heat builds up and the fuse opens to stop operation and reduce overheating risk. The manual also calls out checking for a crushed or kinked vent and verifying strong airflow at the outside exhaust hood.

• Clean the lint screen every load; wash it periodically to remove residue
• Inspect and clean the entire vent run to the outside hood
• Replace plastic or thin foil venting with heavy metal or flexible metal vent
• Confirm the vent is not crushed behind the dryer and the dryer is level

Last updated: February 2026

On Kenmore model 11092826101 dryers, an F26 code points to a door switch or door switch circuit problem. Most often the door is not fully closed, the door strike is misaligned, or the door switch wiring or switch has failed.

• Open and firmly re-close the door; listen for a solid latch click.
• Check for laundry caught between the door and front panel.
• Inspect the latch area for looseness or misalignment.
• Unplug the dryer for 1 minute, then restore power and try a cycle again.

If the door is closing but the code returns, the latch components are a common place to start.

• Door strike/latch alignment: a worn or shifted strike can prevent the switch from proving the door is closed.
• Door switch wiring: loose connectors or a damaged harness can interrupt the door-closed signal.

Helpful model-matched part examples:

• Strike 279570

The door switch is a safety device; the dryer uses it to confirm the door is closed before it will run. If the control does not see a steady door-closed signal, it stops the cycle and posts a fault like F26 to prevent unsafe operation.

Use the wiring diagram, component locations, and disassembly steps in the 11092826101 owner's manual to safely access the door switch area and confirm the correct procedure for your exact Kenmore gas dryer configuration.

Last updated: February 2026

For a Kenmore dryer, replacing a heating element typically costs $20 to $100+ for the part and about $100 to $350 total if you hire service (part plus labor). On your Kenmore gas dryer model 11092826101, “no heat” is often caused by gas-heat components, not an electric heating element, so diagnosis matters.

• Part only (DIY): $20 to $100+ (more if it’s a complete heater housing/assembly)
• Service call/labor: commonly $80 to $250 depending on area and access
• Total installed: commonly $100 to $350

Model 11092826101 is a gas dryer, so heat is produced by a burner system (igniter, gas valve coils, radiant sensor, thermostats, fuses) rather than a traditional electric heater coil. If the drum tumbles but there’s no heat, these parts are the most common cost drivers.

• Dryer thermal fuse WP3390719 (opens if the dryer overheats)
• Igniter 279311 (fails to glow or ignite gas)
• Dryer valve coil kit 279834 (can fail when hot and stop gas flow)
• Dryer radiant sensor WP338906 (does not sense flame properly)
• Dryer high-limit thermostat W11050897 (opens on overheating)

1. Confirm the cycle and heat setting in the 11092826101 owner’s manual.
2. Check airflow: a crushed vent or clogged lint path can cause overheating and blown fuses.
3. If the dryer heats briefly then stops, suspect gas valve coils.
4. If the igniter never glows, suspect the igniter or thermal fuse.

Buying a “heating element” for a gas dryer often leads to the wrong part and extra downtime. A quick symptom check (igniter glow, flame, airflow) usually points to the correct repair and keeps costs closer to the low end.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number label. For Kenmore model 11092826101, the manual specifies the label is located at the top inside the dryer door well; the model number typically begins with 110. (plus additional digits).

Check these common Kenmore dryer label locations (start with the door opening):

• Top inside the dryer door well (most common on Kenmore 110-series dryers)
• Inside the door opening on the cabinet frame
• On the back panel of the dryer cabinet
• Near the lint screen housing (varies by design)

Use the exact model number to match parts like the dryer thermal fuse WP3390719 and to pull the correct 11092826101 owner's manual.

Kenmore model numbers often start with a 3-digit prefix that helps identify the manufacturing source.

Using the full model number (not just “Kenmore gas dryer”) prevents ordering the wrong drum support roller, igniter, or thermostat. It also helps us match the correct wiring diagram, cycle features, and service procedures for your exact dryer.

• Write down model number and serial number exactly as shown
• Take a clear photo of the label for reference
• Match parts by model, then confirm by part ID (example: dryer idler pulley 279640)
• If your dryer shows an error code, use the Kenmore 110 series electronic control model dryer error codes guide to narrow the cause

Last updated: February 2026