$161.92 |
23% OFF MSRP : $210.00
CONFIRM THE PART FITS
Dryer Blower Wheel (replaces 697772) WP697772
Part #WP697772
Online Price
$50.70 |
13% OFF Was : $58.31
In Stock
For ZIP codes near Edit
This part fits
Part Information
Helpful DIY instructions: Installation guide with video.
This blower wheel (part number WP697772) is for dryers.
Blower wheel WP697772 attaches to the drive motor shaft and blows air through the drum and out through the exhaust vent
Disconnect the power before installing this part. Wear work gloves to protect your hands.
Frequently Used Together
- $21.55 |26% OFF MSRP : $29.00
- $23.23 |18% OFF Phone Price : $28.23
- $21.28 |37% OFF MSRP : $34.00
- $17.76 |32% OFF MSRP : $26.00
- $173.51 |5% OFF Phone Price : $183.51
- $10.59 |16% OFF Phone Price : $12.59
- $33.77 |13% OFF Phone Price : $38.77
- $68.95 |22% OFF MSRP : $88.00
- $50.23 |27% OFF MSRP : $69.00
Top models using the same part
| Model Name | Model Number | Diagram Name |
|---|---|---|
| Model #11097502100 Kenmore dryer | 11097502100 | Upper and lower bulkhead |
| Model #11097094300 Kenmore dryer | 11097094300 | Bulkhead |
| Model #11087402110 Kenmore dryer | 11087402110 | Upper and lower bulkhead |
| Model #11097195520 Kenmore dryer | 11097195520 | Bulkhead |
| Model #CS5100XSW1 Whirlpool dryer | CS5100XSW1 | Upper and lower bulkhead |
| Model #11097195820 Kenmore dryer | 11097195820 | Bulkhead |
| Model #11087994800 Kenmore dryer | 11087994800 | Bulkhead |
| Model #11087994100 Kenmore dryer | 11087994100 | Bulkhead |
| Model #MGDX500XW0 Maytag dryer | MGDX500XW0 | Bulkhead parts |
| Model #WGD5610XW0 Whirlpool dryer | WGD5610XW0 | Bulkhead parts |
Reviews
Didn't get what was pictured
We didn't get this part what we got looked like a wagon wheel for a kids play thing.
Arizona, Arizona
Did you find this review helpful?
- Ease of Installation
- Very Difficult
- Duration of Installation
- More than 2 hours
Old wheel hard to remove; new wheel easy to put on
Wheel fitted perfectly. I had to crack the old one off with plyers then use a Dremel cut-wheel to cut slots in the nut that was too tight to remove. There are a couple of You-Tube videos out there to show you how to replace this wheel. But none showed me how to remove the nut that was fused to the shaft. That's where the Dremel came in handy. By cutting two slots in the nut opposite each other and in line with the shaft I was able to pry off the nut with a flathead screwdriver (being careful not to disturb the threads on the shaft). The new wheel screwed on eaisly. I did this without removing the drum as shown in some how to videos.
Smoses, Dallas TX
1 person thought this review was helpful.
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour
Yes, I would recommend this to a friend
Easy to install
It only took a few minutes to install. Just remember that it's left hand threaded!
Shniz, Phoenix, AZ
Did you find this review helpful?
- Ease of Installation
- Easy
- Duration of Installation
- 30 minutes - 1 hour
medium difficulty
Not easy for people that are not mechanically inclined.
maverick43, Michigan
Did you find this review helpful?
- Ease of Installation
- Moderate
- Duration of Installation
- 30 minutes - 1 hour