Kenmore Elite 66516262402 dishwasher Parts

Standing water in your Kenmore Elite dishwasher model 66516262402 usually means the drain path is restricted (air gap, disposer inlet, drain hose, or filters). We recommend removing the water first, then clearing the drain connection and checking the drain hose routing described in the 66516262402 installation guide.

Step 1: Remove the standing water safely

• Turn off power at the breaker (and unplug if accessible).
• Place towels under the door area to catch spills.
• Scoop water out with a cup, then soak up the remainder with towels or a sponge.
• If the water is dirty, wear gloves and avoid splashing.

Step 2: Clear the most common drain restrictions

The manual calls out the drain air gap as a common cause of backup; cleaning it often restores normal draining.

• Clean the drain air gap (if your setup has one): lift the cover, remove the cap, and clear debris per the 66516262402 owner’s manual.
• If connected to a garbage disposer: make sure the disposer inlet plug was removed when the dishwasher was installed.
• Check the sink drain or waste tee: a slow kitchen drain can cause dishwasher backup.
• Inspect the drain hose: look for kinks, crushing, or a low spot that traps water.

Drain hose routing checklist (helps prevent repeat backups)

Use these routing rules from the installation guidance:

• Route the hose so it does not touch the motor, door springs, water line, cabinet edges, or flooring.
• Keep the factory drain loop in place on the side of the dishwasher.
• Make sure the hose is fully seated to the connector stop and clamped securely.

What you see	Likely cause	What to do
Water backs up into tub after sink use	Clogged air gap or sink drain	Clean air gap; clear sink drain
Hose looks pinched behind unit	Kinked drain hose	Re-route or replace hose
Leaks at drain connection	Loose clamp or poor seating	Re-seat hose; tighten clamp

When a part replacement makes sense

If the hose is brittle, split, or permanently kinked, replacing it is the reliable fix. Use a new hose as recommended during installation; the correct replacement for this model is the dishwasher drain hose 8269144A.

Why it matters

Standing water can cause odors, poor wash results, and can trigger drain-related error behavior. Restoring proper drainage protects the pump and keeps cycles completing normally.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66516262402, an F2 E2 code typically points to a user interface or keypad communication issue. Start by clearing the cycle using the control panel (Cancel/Drain), then restore normal operation by restarting the cycle per the steps in the 66516262402 owner's manual.

Quick reset steps (most effective first)

• Press CANCEL/DRAIN to stop the cycle and run the drain (about 2 minutes if needed).
• Keep the door closed and latched while the dishwasher drains.
• After draining, select a new cycle.
• Press START/RESUME to restart.
• If the Start/Resume light is flashing, close the door fully and press START/RESUME again.

If the code comes back right away

F2 E2 often returns when the keypad is seeing a stuck key, moisture, or a control communication problem.

• Turn off power to the dishwasher at the breaker for 1 minute, then restore power.
• Wipe the control area dry (especially after steam-heavy cycles).
• Press each key once to confirm none feel stuck.
• If the dishwasher will not respond or the code repeats, inspect for signs of water intrusion around the vent and door area.

What “Cancel/Drain” does (and why it matters)

Cancel/Drain clears active cycles and options so the control can start fresh. This is the fastest “reset” for many control-related symptoms.

Action	What it does	When to use it
CANCEL/DRAIN	Stops the cycle and drains (if needed)	Error shows mid-cycle, wrong cycle selected
START/RESUME	Restarts or resumes after door opens/power interruption	Start light flashing, cycle paused
Breaker reset (1 minute)	Reboots the electronic control	Controls unresponsive, code returns immediately

Related help

For code meanings and what to check next, use our Kenmore 665 model dishwasher error codes reference.

Why it matters

Resetting the control correctly prevents repeated drain loops, helps protect the heater circuit from interrupted cycles, and confirms whether the issue is a temporary keypad glitch or a part-related failure.

Last updated: January 2026

On the Kenmore Elite 66516262402 dishwasher, the most reliable “hard reset” is to cancel the current cycle and clear the control indicators using the Cancel/Drain function, then restart a new cycle. This resets the cycle logic and gets the control back to a known state; see the 66516262402 owner's manual.

Quick reset steps (Cancel/Drain reset)

• Press CANCEL/DRAIN once.
• Keep the door closed so the dishwasher can drain.
• Let the drain run for about 2 minutes (typical Cancel/Drain time).
• Press CANCEL/DRAIN again if you need to stop the drain.
• Select a new cycle and options, then press START/RESUME.

If the controls seem “frozen” (Lock On is enabled)

If the dishwasher won’t respond to button presses, the control lock may be on.

• Press and hold HEATED DRY for 4 seconds to toggle Lock On.
• When LOCK ON is lit, all buttons are disabled.
• After unlocking, press START/RESUME to continue a cycle if needed.

What to do after a power interruption

A power blink can leave the dishwasher paused with the Start/Resume light flashing.

• Close the door fully and latch it.
• Press START/RESUME to resume.
• If you want to start over, use CANCEL/DRAIN first, then choose a new cycle.

Reset options at a glance

Situation	Best “reset” action	What you should see
Wrong cycle/options selected	CANCEL/DRAIN, then reselect	Options cleared, then restart
Dishwasher won’t respond	Toggle Lock On (HEATED DRY 4 sec)	LOCK ON light turns off
Start/Resume light flashing	Press START/RESUME	Cycle resumes

Why it matters

Cancel/Drain clears the current program and drains the tub so you do not restart a cycle with leftover water, detergent, or a paused sequence. That prevents poor cleaning, standing water, and confusing indicator lights.

Last updated: January 2026