Kenmore Elite 66513113K701 dishwasher Parts

To hard reset your Kenmore Elite dishwasher model 66513113K701, we recommend using the built-in control reset: press CANCEL/DRAIN twice to reset the control, then reselect your cycle and press START/RESUME. Steps and button behavior are shown in the 66513113K701 owner's manual.

• Open the door slightly to stop the cycle.
• Wait until spraying stops, then open the door fully.
• Check the detergent dispenser; refill if it opened.
• Press CANCEL/DRAIN twice to reset the control.
• Select a new cycle and options.
• Close the door firmly and press START/RESUME.

On this Kenmore Elite dishwasher, the Control Lock disables all buttons when LOCK ON is lit.

• Press and hold HEATED DRY for 3 seconds.
• Confirm LOCK ON turns off.
• Try the reset steps above again.

A proper reset clears a stuck cycle and restores normal keypad response without guessing button combinations. It also helps you avoid restarting with an empty detergent cup or leaving water in the sump.

Last updated: January 2026

On Kenmore Elite dishwasher model 66513113K701, the F4E1 error code points to a wash (circulation) pump or wash motor problem, meaning the dishwasher is not moving water through the spray arms correctly. After correcting the cause, clear the code using the reset steps in the 66513113K701 owner's manual.

• Turn off power at the breaker for 1 minute, then restore power and try a cycle.
• Cancel and drain the cycle; listen for the drain pump running and water evacuating.
• Check that the sump area is clear of debris that can jam the impeller.
• Confirm the dishwasher is filling; low or no fill can mimic a wash pump fault.
• Verify the spray arms spin freely and are not blocked by tall items.

Many Kenmore 665-series electronic-control dishwashers clear stored faults by using a 3-key sequence:

• Press any 3 keys in a 1-2-3 pattern
• Repeat the same pattern 3 times: 1-2-3, 1-2-3, 1-2-3
• Close the door and allow the unit to run the brief reset/diagnostic routine

For the exact key sequence and what the lights should do on 66513113K701, follow the steps in the 66513113K701 owner's manual.

If the dishwasher fills but does not wash (no strong spray sound, poor cleaning), these parts are common suspects:

• Pump motor WPW10780877 (main wash motor assembly)
• Dishwasher pump motor WPW10239401 (circulation pump motor)
• Wiring connections at the motor and control
• Control output issues (less common)

The wash pump is what creates pressure to spin the spray arms. When it fails or is blocked, dishes stay dirty and the dishwasher may stop mid-cycle or store repeating fault codes.

Last updated: January 2026

Dishwasher capacity for the Kenmore Elite 66513113K701 is measured in place settings (not cubic feet). Standard built-in Kenmore 665-series dishwashers typically hold 12 to 14 place settings; confirm the exact rating and rack loading diagram in the 66513113K701 owner's manual.

Capacity is based on how many standard dish sets fit while still allowing proper spray-arm rotation and water flow.

• Place settings are the standard measure for dishwashers
• Rack design and adjustability affect usable capacity
• Overloading reduces wash performance even if items physically fit

Use these quick checks alongside the rack diagrams in the manual:

• Look for the place-setting specification in the “features” or “loading” section
• Compare your rack layout to the manual’s loading illustrations
• Verify whether the upper rack is adjustable and how that changes tall-item loading
• Check the silverware basket size and placement options

Knowing the place-setting capacity helps you choose the right cycle, avoid poor cleaning from blocked spray paths, and reduce issues that look like “low capacity” performance (spotting, food bits, or poor draining).

For efficiency tips that also improve real-world capacity, use how to use your dishwasher efficiently.

Last updated: January 2026