Kenmore 79572595710 refrigerator Parts

On Kenmore refrigerator model 79572595710, an ice maker “reset” is done by power-cycling the ice maker: turn the ice maker OFF at the control panel, wait about 30 seconds, then turn it ON again and allow time for the unit to reach 15°F (-9°C) or colder before it starts cycling.

• Set the ice maker button/switch to OFF (O).
• Wait 30 seconds.
• Set the ice maker button/switch back to ON (I).
• Confirm the ice bin is seated correctly and the ice compartment door closes tightly.
• Wait for temperature: the ice maker starts automatically once the freezer is 15°F (-9°C) or below.
• Give it time: normal ice production can take several hours after a reset.

For the exact control panel layout and ice maker ON/OFF location for this model, follow the 79572595710 owner's manual.

These checks fix most “no ice after reset” complaints on bottom-mount models:

• Ice bin full or uneven: empty the bin and reinsert it; level/shake cubes so the ice maker reads the level correctly.
• Shutoff (feeler arm) blocked: make sure the auto shutoff arm moves freely and is not held up by ice.
• Water supply issue: verify the household shutoff valve is open and the line is not kinked.
• Air in the water line: flush the dispenser in short cycles (30 seconds on, 60 seconds off) to clear trapped air.
• Ice compartment door not sealing: close it firmly; warm air leaks can stop ice production.

Resetting the ice maker clears a stalled cycle and forces the system to re-check bin level, temperature, and water fill. If the freezer is not cold enough or the shutoff arm is blocked, the ice maker will not restart even after a reset.

Last updated: February 2026

Kenmore refrigerator model 79572595710 is a 795-prefix (LG-built) bottom-mount style; most refrigerators in this family are about 20 to 22 cubic feet. For the exact cubic-foot capacity for your specific unit, we recommend checking the specifications section in the 79572595710 owner's manual.

You can usually confirm cubic feet without tools by checking the model and rating label location described in the manual.

• Look for the identification label inside the fresh food compartment (often on the interior liner)
• Match the model number exactly: 79572595710
• Check the “Specifications” or “Product information” section for total capacity
• If the manual lists separate capacities, add refrigerator + freezer for total cubic feet

If you are comparing models or planning kitchen space, these are common ranges for Kenmore 795 bottom-mount refrigerators.

Knowing cubic feet helps with food storage planning, replacement shopping, and confirming you are ordering the right shelves, drawers, and door bins for the correct platform.

When ordering parts for this Kenmore refrigerator, always use the full model number 79572595710 (not just “795”), because the 795 prefix identifies the manufacturer family, not the exact configuration.

Last updated: February 2026

If your Kenmore refrigerator model 79572595710 is warmer at the bottom, the most common causes are blocked air vents, frequent door openings, or the unit being in demo mode or a defrost cycle. Start by restoring airflow and confirming the controls are set correctly using the 79572595710 owner's manual.

• Clear air vents in the fresh food section and freezer; rearrange items so air can circulate.
• Reduce door-open time; long openings let warm, humid air in and raise compartment temps.
• Confirm cooling is enabled; some models can be set to OFF or demo mode, which keeps lights on but disables cooling.
• Wait out a defrost cycle; temps can rise slightly during defrost, then recover.
• Allow time after moving/installation; cooling can take up to 24 hours to stabilize.

Warm at the bottom can also happen when cold air is not being moved effectively through the refrigerator compartment.

• Listen for the evaporator fan; if it is not running or is noisy, inspect the refrigerator evaporator fan motor EAU63923603.
• Check for heavy frost on the rear freezer panel (a sign of airflow restriction from icing).
• Make sure the doors seal tightly; air leaks can cause uneven temperatures.

Bottom-warm conditions usually mean airflow is restricted or cooling is temporarily disabled. Fixing airflow and settings first prevents unnecessary part replacement and helps protect food temperatures.

Last updated: February 2026

Most Kenmore refrigerators, including the Kenmore 79572595710 bottom-mount style, typically last 10 to 15 years with normal household use. Regular maintenance (cleaning condenser coils, keeping door gaskets sealing, and using the correct water filter) helps you reach the high end of that range.

A refrigerator’s life depends more on operating conditions than brand name alone.

• Heat and airflow: Dirty condenser coils or blocked airflow make the compressor run longer.
• Door seal condition: Worn gaskets leak cold air and increase run time.
• Power quality: Frequent outages and surges add stress to electronics.
• Ice and water use: Heavy dispenser use increases wear on valves, motors, and the ice maker.
• Cleaning and upkeep: Simple routine care prevents many early failures.

For model-specific care and operating guidance, follow the maintenance and troubleshooting sections in the 79572595710 owner’s manual.

Use this quick routine to reduce strain on the sealed system and cooling fans:

• Vacuum and brush condenser coils every 6 to 12 months.
• Confirm doors close easily and the cabinet is level.
• Clean and inspect door gaskets; replace if torn or warped.
• Replace the water filter on schedule; use the correct cartridge such as Kenmore refrigerator water filter 9980 AGF80300805 when applicable.
• Keep vents inside the fresh food section and freezer unblocked.
• After a power interruption, allow temperatures to stabilize before adjusting controls.

These symptoms often show up as a refrigerator approaches major repair territory:

A well-maintained refrigerator holds safe food temperatures with less run time, which reduces wear on high-cost components like the compressor and control boards and can extend service life.

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 79572595710 are weak or no cooling, ice maker and water dispensing issues, water leaks, and unusual noises. These problems usually trace back to airflow, door sealing, temperature settings (including demo mode), or a failing fan or water component; use the 79572595710 owner's manual for model-specific checks.

• Not cooling or weak cooling: demo mode enabled, controls set incorrectly, unit in defrost cycle, or restricted airflow.
• Too warm in fridge or freezer: blocked air vents, frequent door openings, or hot room conditions.
• Ice maker not making enough ice: freezer temperature too warm (target 0°F), doors not closing fully, or low water pressure.
• Slow water dispensing: exhausted water filter.
• Leaks or puddles: clogged/iced defrost drain, kinked water line, or a leaking connection.

1. Confirm cooling is enabled and demo mode is off.
2. After changing settings, allow time to stabilize (up to 24 hours after installation).
3. Keep packages clear of air vents so cold air can circulate.
4. Minimize long door openings; warm, humid air raises temps fast.
5. Verify water supply basics: potable water, 20 to 120 psi, and no kinked tubing.

• Airflow and noise issues: refrigerator evaporator fan motor EAU63923603
• Door sealing and moisture: lg refrigerator door gasket, left ADX73550621, lg refrigerator door gasket, right ADX73550624
• Slow dispensing: Kenmore refrigerator water filter 9980 AGF80300805

Most cooling, ice, and leak complaints share the same root causes: airflow, door sealing, and water supply. Fixing those first prevents food spoilage, reduces frost, and helps the compressor run less.

Last updated: February 2026