Kenmore 11096565210 electric dryer Parts

Your Kenmore dryer’s model number is printed on the appliance’s ID label; once you find it, match it exactly (all digits) to look up the correct parts and diagrams. For this page, the model number is 11096565210.

Check these common locations on Kenmore electric dryers:

• Inside the door opening on the front panel (most common)
• On the door itself (edge or inner surface)
• On the back panel of the cabinet
• Near the lint screen housing (some designs)
• On the side panel near the door opening

Kenmore model numbers are usually a long string of numbers. Write it down exactly as shown, including any leading digits.

Before ordering a belt, heating part, or switch, we use these checks:

• Confirm the label says Kenmore and the full model number matches 11096565210
• Avoid using only “110” or “Kenmore 110 series”; those are not specific enough
• Compare your part to the listing by name and ID (for example, drum belt 341241)
• If the dryer won’t start, verify the door closes and the switch clicks (common with dryer door switch W10820036)
• If the dryer runs but won’t heat, focus on airflow and heating circuit parts (often the element 279838)

Kenmore dryers share many look-alike parts across different model families. Using the exact model number prevents mismatched items like a drum belt, heating element, or thermal cut-off kit that can look similar but mount differently.

Last updated: February 2026

To hard reset your Kenmore electric dryer model 11096565210, disconnect power (unplug the cord or switch the breaker off) for 5 minutes, then restore power and try a normal cycle. This clears many control glitches, stuck indicators, and unresponsive buttons.

• Turn the dryer OFF.
• Unplug the dryer (or turn both dryer breakers OFF if it is hardwired).
• Wait 5 minutes (a full 5 minutes helps the control fully discharge).
• Restore power.
• Open and close the door once, then select a cycle and press Start.

A reset only clears the symptom; it does not fix a failed part. Check these common causes next:

• Door not fully closed or a failed door switch (see dryer door switch W10820036).
• Blown thermal cut-off or overheating protection trip (see cut-off kit 279816).
• No heat complaints after reset: heating circuit issue (see element 279838).
• Dryer runs but takes too long: airflow restriction; clean lint screen and venting (see screen W10874409).
• Drum will not turn or you hear motor running: belt or idler problem (see drum belt 341241 and dryer idler pulley WP691366).

Resetting is a fast first step because it restores the control to a known state. If the same problem returns, focusing on airflow, the door switch, and the heating safety devices prevents repeat shutdowns and helps protect the heating element and motor.

Last updated: February 2026

On Kenmore electric dryer model 11096565210, we remove the front panel by disconnecting power, opening the top to access the mounting screws, then lifting the front panel up and off the lower retaining clips while supporting the drum. This gives access to the belt, idler pulley, and motor.

• Unplug the dryer from the wall outlet.
• If it is hardwired, switch OFF the breaker and verify the dryer is dead.
• Pull the dryer forward so you can reach the rear and sides.
• Wear cut-resistant gloves; cabinet edges are sharp.
• Keep a small container for screws so nothing gets lost.

1. Remove the lint screen from the top panel.
2. Remove the two screws that are usually located in the lint screen housing opening.
3. Use a putty knife to release the spring clips at the front corners of the top; lift the top up.
4. Disconnect the door switch wire harness if it is attached to the front panel.
5. Remove the screws securing the front panel to the cabinet (commonly near the top inside corners).
6. Tilt the front panel forward slightly, then lift it up to unhook it from the bottom clips.
7. If the drum drops forward, support it; the belt and drum can shift.

Removing the front panel the right way prevents bent panels, broken retaining clips, and pinched wiring. It also makes belt and motor service much easier, especially when replacing wear items like the belt or idler pulley.

Last updated: February 2026