Owner’s manual
How to look up chainsaw serial number?
For the Craftsman gas chainsaw model 358356332, we look up the serial number by first finding it on the saw itself. On this model, the serial number is located below the top handle, next to the model number, so you can record it exactly for parts lookup and service reference (see the 358356332 owner's manual).
Check these common spots on the saw:
- Below the top handle (the primary location for this model)
- On the housing near the model number plate/label
- On a flat stamped area of the engine housing (varies by production run)
Once you have the serial number, use it with the model number to make sure you get the right chainsaw parts (bar, chain, fuel line, carburetor gaskets).
- Write down the model number: 358356332
- Write down the serial number exactly as shown
- Use the model number first when selecting parts; use the serial number to confirm you are matching the correct production version
| Item | What it does | Where you use it |
|---|---|---|
| Model number (358356332) | Identifies the chainsaw design | Parts diagrams and parts list |
| Serial number | Identifies your specific unit | Confirms exact unit/version |
Chainsaw parts can change across production runs. Having the correct serial number helps prevent ordering the wrong bar, chain, or fuel system parts for your Craftsman 358356332.
Last updated: February 2026
What model number is a Craftsman 358356332 chainsaw?
The model number for this Craftsman gas chainsaw is 358356332. You will see it shown in the parts list and diagrams for the MODEL 358.356332 chainsaw; use this exact number when looking up parts and service information in the 358356332 owner's manual.
Most Craftsman gas chainsaws list the model number on the product ID label. Common spots include:
- On the rear handle area near the fuel tank
- On the starter housing (recoil cover) side
- Near the bar mount area (clutch cover side)
- On a label or stamped plate on the chassis
Craftsman chainsaws in the 358.xxxxxx family can look similar, but parts can differ by bar length, handle/fuel tank assemblies, and carburetor components. Using 358356332 helps us match the correct chainsaw parts list and avoid ordering the wrong items.
The manual and parts list may show the model with punctuation. These formats refer to the same model:
| How it appears | What it means |
|---|---|
| 358356332 | Model number used for ordering parts and manuals |
| 358.356332 | Same model number with a dot formatting used in parts lists |
If you are confirming the model to buy parts, these are examples of items that must match the correct model and configuration:
- Bar and chain (length and pitch must match)
- Fuel and impulse lines (routing and sizes vary)
- Carburetor gaskets and diaphragms
- Clutch drum sprocket
For example, if you are replacing fuel lines, we list a compatible line kit 530069216 for this model.
A correct model match saves time and prevents fit issues, especially on wear items like the chain, bar, and fuel system parts.
Last updated: February 2026
Should I use 40 1 or 50 1 fuel for a chainsaw?
For the Craftsman gas chainsaw model 358356332, use a 40:1 fuel mix: 1 part air-cooled 2-cycle engine oil to 40 parts regular unleaded gasoline. This is the mix ratio specified for this model in the 358356332 owner's manual.
Use these practices every time you mix fuel:
- Mix fuel in an approved container, not in the saw’s fuel tank
- Use fresh gasoline (gas older than about 2 months causes hard starting and engine damage)
- Use air-cooled 2-cycle engine oil (not automotive oil)
- Do not use NMMA marine 2-cycle oil
- Shake or stir the container to mix thoroughly before filling
| Gasoline amount | Oil amount for 40:1 |
|---|---|
| 1 gallon | 3.2 fl oz |
| 2.5 gallons | 8.0 fl oz |
| Ratio | Oil content | What you can expect |
|---|---|---|
| 40:1 | Higher | Correct lubrication level for this model’s engine |
| 50:1 | Lower | Less lubrication; increases overheating and scoring risk in a 40:1 engine |
A 2-cycle chainsaw engine is lubricated by the oil mixed into the gasoline. Too little oil or the wrong oil overheats the engine and can seize it; too much oil fouls the spark plug and increases carbon deposits.
Last updated: February 2026
Where is the model number on a chainsaw?
On the Craftsman gas chainsaw model 358356332, the model number is printed on the identification label below the top handle, with the serial number. This is the primary ID location to use when matching parts and diagrams; clean the area so the label is readable.
- Check under the top handle on the saw body.
- Look for a printed label or plate that lists both model and serial.
- Wipe off oil, sawdust, and pitch before reading.
- Use a flashlight; angled light helps with faded print.
- Copy the number exactly as shown (including any punctuation).
| Tag type | What you will see | Best way to read it |
|---|---|---|
| Printed label | Model and serial printed in ink | Clean gently; avoid scraping |
| Metal plate | Stamped or etched numbers | Shine light across at an angle |
The model number is how we match the correct Craftsman parts list for items like a guide bar, chain, fuel line, or starter components. Using the exact ID prevents ordering parts that do not fit.
- Model number: 358356332
- Serial number (if shown)
- The part number from the parts diagram or list
For the documented ID location and parts-ordering notes, use the 358356332 owner's manual.
Last updated: February 2026
