Kenmore 10658144800 side-by-side refrigerator Parts

For Kenmore model 10658144800, the most reliable way to get the exact cubic-foot capacity is to check the model and serial (rating) label inside the refrigerator compartment and confirm the listed specifications in the 10658144800 owner's manual. This avoids guessing based on similar 106-series models.

On most Kenmore side-by-side refrigerators, the rating label is inside the fresh food section (often on a side wall near the crisper area or upper cabinet).

• Look for a label that lists model, serial, and electrical information
• Check for a line that says capacity, total volume, or cu. ft.
• If the label is hard to read, take a photo and zoom in
• Confirm the number in the specifications section of the manual

Kenmore model numbers do not consistently encode cubic-foot capacity in a way that is accurate for every revision. For a 36-inch side-by-side like 10658144800, total capacity is typically in a mid-to-high range.

Cubic-foot capacity helps when we are matching storage parts (bins, shelves, crisper pans) and setting expectations for cooling load. It also prevents ordering the wrong-fit items for your Kenmore 106-series platform.

If you are shopping for common maintenance items, we match by model number and part ID, not cubic feet.

• Genuine Kenmore refrigerator water filter EDR3RXD1 (water and ice filtration)
• Refrigerator temperature control WP2315562 (temperature regulation)
• Refrigerator evaporator fan motor WP2315549 (air circulation)

Last updated: February 2026

The most common problems we see on Kenmore refrigerators like model 10658144800 are cooling issues (often airflow or defrost related), water leaks, ice maker and dispenser troubles, and new or unusual noises. Many fixes start with correct temperature settings, keeping vents clear, and checking key components.

• Not cooling or warm temperatures: blocked vents, dirty condenser area, evaporator fan problems, or a defrost system issue causing frost buildup
• Freezer cold but refrigerator warm: restricted airflow between sections, iced-up evaporator area, or a weak evaporator fan motor
• Water leaking or puddles: clogged defrost drain, loose water line connections, or door seal problems causing excess moisture
• Ice maker not making ice: water supply issue, frozen fill tube, or a failing ice maker assembly
• Noises (buzzing, rattling, pulsating): normal water valve fill sounds, refrigerant movement, or fans and compressor adjusting during operation

Use these steps before replacing parts; they match common troubleshooting guidance in the 10658144800 owner's manual.

• Confirm the unit is plugged into a grounded 3-prong outlet and the breaker is not tripped
• Make sure the controls are on and set near the factory mid-settings
• Wait 24 hours after any temperature change or new installation for temps to stabilize
• Do not block airflow vents with food packages (blocked vents cause temperature and moisture problems)
• If the refrigerator seems to run a lot, consider room temperature, door openings, and large food loads

If symptoms point to a specific system, these parts are commonly involved on this model:

Most “not cooling” and “leaking” complaints come down to airflow and moisture control. Keeping vents open, using stable temperature settings, and addressing early frost or seal issues prevents food spoilage and reduces compressor run time.

Last updated: February 2026

On Kenmore model 10658144800, the ER IF code points to an ice maker fan (ice compartment fan) airflow problem. Most often, the fan is blocked by ice buildup, the fan motor is failing, or the wiring/control is not powering the fan correctly; clearing the ice and restoring airflow usually fixes it.

• Unplug the refrigerator or turn off power at the breaker before accessing the fan area.
• Empty the ice bin and look for frost or a solid ice mass around the ice maker and fan ducting.
• Make sure the freezer door closes fully and the door seal is making full contact.
• Confirm the vents between the freezer and ice storage area are not blocked by packages.
• Restore power and listen for the fan; a working fan typically runs when cooling is needed.

1. Reset and observe: Power the unit off for 2 minutes, then back on; watch if ER IF returns.
2. Defrost the ice room area: If you see heavy frost, fully defrost the ice compartment (doors open, towels down). Do not chip ice with sharp tools.
3. Inspect the fan blade: If the blade is rubbing ice or not spinning freely, clear obstructions.
4. Check for recurring frost: If frost returns quickly, the issue often ties to defrost/airflow problems.

If the fan is noisy, stalled, or not running after ice is cleared, these model-compatible parts are common fixes:

When the ice fan cannot move cold air, the ice maker area warms up, ice production drops, and frost can spread. Fixing airflow early helps protect food temperatures and reduces compressor run time.

For control settings, airflow guidance, and ice maker section details, use the owner's manual.

Last updated: February 2026