Maytag LDE9904ACL washer/dryer Parts

On a Maytag LDE9904ACL dryer, the model number is typically on the cabinet frame in the door opening, or on the back panel near where the vent connects. We use that exact model number to match the correct Maytag dryer parts and diagrams for your unit.

• Open the dryer door and look around the door opening (cabinet frame) for a model and serial tag
• Check the inside of the front panel near the lint screen housing (some versions place the tag nearby)
• Look on the back of the dryer cabinet, often near the exhaust vent outlet
• If your dryer is stacked or tight to a wall, pull it forward a few inches to see the rear label safely

• Use a flashlight and look for a silver or white sticker or metal tag
• Wipe dust off the label gently so the characters are readable
• Write down the full model number exactly as shown (including any letters)

Maytag dryers can have similar-looking cabinets across multiple model series; using the exact LDE9904ACL model number prevents ordering the wrong items such as a gas igniter 4391996 or dryer thermal fuse, 243-degree f WP307473.

Last updated: February 2026

Yes, many Maytag and Whirlpool dryer parts can interchange, but we always match parts by the exact model number and the original part ID. For your Maytag dryer model LDE9904ACL, confirm fit by using the parts list for that model before ordering.

We treat “interchangeable” as “same fit and function on the same model series.” Use these checks:

• Match your dryer’s full model number: LDE9904ACL
• Compare the part ID and description, not just the brand name
• Confirm the part’s location and function (heat system, drum support, drive system)
• Watch for gas vs. electric differences (they use different heating components)
• Replace paired wear parts together when recommended (for example, drum support items)

These parts are listed for LDE9904ACL and are safe starting points when you are comparing Maytag vs. Whirlpool-branded replacements:

• Heating and ignition: gas igniter 4391996, gas sensor WP338906
• Safety and no-heat issues: dryer thermal fuse, 243-degree f WP307473
• Gas valve operation: holding coil 279834

A dryer can look identical across brands, but small differences (connector type, temperature rating, bracket shape) can cause a no-heat condition, poor drying, noise, or premature part failure. Matching to LDE9904ACL prevents ordering the wrong component.

Last updated: February 2026

To clear an error code on your Maytag dryer model LDE9904ACL, we reset power to the control by unplugging the dryer (or switching the breaker off) for a few minutes, then restoring power. If the code returns, troubleshoot the underlying heating, airflow, or wiring issue.

• Turn the dryer OFF.
• Unplug the power cord (or switch the dryer breaker OFF).
• Wait 1 to 5 minutes.
• Restore power and start a cycle.
• If the code reappears, stop the cycle and move to the checks below.

Many recurring dryer codes are triggered by overheating, no-heat, or electrical sensing problems.

• Airflow restriction: clean the lint screen; check the vent hose for kinks or crushing; confirm strong airflow outside.
• Overheat protection: a blown thermal fuse often points to poor venting; check the dryer thermal fuse, 243-degree f WP307473.
• Heating system (gas models): if the dryer tumbles but won’t heat, inspect the igniter and flame sensing circuit; common suspects include the gas igniter 4391996 and gas sensor WP338906.
• Gas valve coils: intermittent heat (heats once, then stops) commonly tracks back to weak coils; check the holding coil 279834.
• Wiring connections: look for loose terminals or damaged wires at the heater, sensor, and control.

Clearing the code only resets the control. If the dryer is overheating or failing to ignite, the code will return until airflow, heating parts, or wiring are corrected.

Last updated: February 2026

Most Maytag dryers use a 93 1/2-inch drum drive belt, and that is the common replacement size you will see for many Maytag-built 29-inch dryers. For your Maytag model LDE9904ACL, confirm the exact belt by matching the belt routing and drum size, then order the correct belt from the parts list for this model on Sears PartsDirect.

• Check the model tag and use LDE9904ACL when selecting parts.
• Compare your old belt length and rib style (most are ribbed on one side).
• Inspect belt routing around the motor pulley and idler pulley.
• If the belt snapped, look for glazing or cracking that indicates age and heat.
• If the drum does not turn but the motor runs, the belt is the first item to verify.

A belt failure is often caused by drag or a tensioning problem. While you have the cabinet open, we recommend checking these common wear items:

• Dryer drum bearing kit 306508 for drum support wear that increases friction
• Dryer drum felt seal WP314820 for rubbing, heat buildup, and poor drum support

Using the correct belt size and routing keeps proper tension on the drum, prevents slipping, and protects the motor and idler system from overload. A slightly wrong belt length can cause noise, poor tumbling, or repeated belt breakage.

Last updated: February 2026

The L2 line voltage error on your Maytag dryer model LDE9904ACL means the dryer is not sensing proper power on the L2 side of the supply, so the heater cannot turn on. The drum can still tumble, but you will get little or no heat until the power issue is corrected.

• Dryer runs but clothes stay cool or take much longer to dry
• No heat on heated cycles, but air flow may feel normal
• Error may clear and return depending on the power interruption
• Problem often shows up after a breaker trip or power outage

1. Reset the power: Turn the dryer off, then reset the dryer breaker fully OFF then back ON.
2. Check for a tripped breaker: Many dryers use a 2-pole breaker; one side can trip and the motor still runs.
3. Confirm the outlet is a dryer outlet: Electric dryers need a 240V supply (gas dryers typically use 120V).
4. Try a timed dry heat cycle: If it tumbles but never heats, treat it as an L2 supply problem first.

Once you have confirmed proper supply voltage, a no-heat condition can also be caused by a failed safety device or heater circuit component.

Common parts to inspect or test include:

• Dryer thermal fuse, 243-degree f WP307473 (opens if the dryer overheats)
• Cut-off, the WP306604 (thermal cut-off in the heater or burner safety circuit)
• Heating system components (electric heater assembly or gas ignition parts, depending on how your LDE9904ACL is configured)

The L2 error is designed to prevent the dryer from trying to heat with incorrect voltage. Fixing the power supply issue first avoids unnecessary part replacement and helps protect the heater or gas ignition system.

Last updated: February 2026