Kenmore Elite 11042822202 washer with horizontal axis Parts

The Kenmore Elite washer model 11042822202 has a 4.0 cu. ft. capacity. The “110” series label covers many different designs, so capacity changes by the exact model and whether it is a front-load (horizontal-axis) or top-load washer; confirm specs in the 11042822202 owner's manual.

Capacity basics for Kenmore 110-series washers

Capacity is determined by the specific model’s tub size and platform, not the “110” prefix.

• Front-load (horizontal-axis) models commonly run 3.5 to 4.5 cu. ft.
• Traditional top-load (agitator) models commonly run 2.5 to 3.5 cu. ft.
• HE top-load (impeller) models commonly run 3.5 to 5.0 cu. ft.
• Capacity affects load size, cycle selection, and detergent amount (HE detergent for HE washers)

Quick comparison table

Washer style	Typical capacity range	Best for
Front-load (horizontal-axis)	3.5 to 4.5 cu. ft.	Large loads, high spin extraction
Top-load with agitator	2.5 to 3.5 cu. ft.	Mixed loads, simpler loading
HE top-load with impeller	3.5 to 5.0 cu. ft.	Bulky items, larger tub opening

How to verify you have the right capacity

Use these checks so you are matching the correct Kenmore Elite washer specs:

• Confirm the full model number on the rating label is 11042822202
• Look for the “Capacity” or “Specifications” section in the 11042822202 owner's manual
• If you are comparing washers, match washer style (front-load vs top-load) and cu. ft.

Why it matters

Knowing the cubic feet helps us size loads correctly, reduce oversudsing, and choose compatible parts and accessories for your Kenmore Elite washer.

Last updated: February 2026

To hard reset your Kenmore Elite washer model 11042822202, unplug it (or switch off the breaker) for 1 minute, then restore power and start a fresh cycle. This clears many temporary control glitches without changing any settings permanently.

Hard reset steps (recommended)

• Press Power/Cancel to stop the cycle.
• Unplug the washer from the outlet (or turn OFF the dedicated breaker).
• Wait 60 seconds.
• Restore power.
• Open and close the door firmly, then select a new cycle and press Start.

For model-specific control panel behavior and cycle restart details, follow the 11042822202 owner's manual.

If the washer still will not start after a reset

These checks solve the most common “dead” or “won’t run” complaints on horizontal-axis washers:

• Confirm the outlet has power (test with a lamp).
• Make sure the door is fully closed and latching; a failed lock can prevent any cycle from starting.
• If the tub is full of water and it will not drain, the control may refuse to continue the cycle.
• If it fills slowly or not at all, verify both water supply valves are fully open.
• If the display acts erratically after power is restored, repeat the reset once and then move to part checks.

Quick symptom-to-part guide

What you see	What it usually points to	Common next step
Door clicks but won’t lock/start	Door lock issue	Inspect/replace door lock WP8182634
Water left in tub, won’t drain	Drain pump or drain path	Check filter/hoses; consider water pump 280187
No/low fill, long fill times	Inlet valve or supply restriction	Clean screens; consider washer water inlet valve WP8181694

Why it matters

A hard reset restores normal communication between the control and key components (door lock, drain pump, inlet valve). If the same symptom returns right away, the reset helped identify a hardware problem rather than a one-time software hiccup.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore washer, especially a Kenmore Elite 11042822202 front-load (horizontal-axis) washer, when the fix restores reliable operation for less than the cost of replacing the machine. Most repairs are cost-effective when the tub and motor system are sound and the problem is limited to common service parts.

Quick way to decide

Use these checkpoints before you spend money on parts or labor:

• Age vs. typical lifespan: Front-load washers typically last 10 to 14 years.
• Type of failure: Drain, fill, and door-lock issues are usually straightforward repairs.
• Leak location: Door-boot and hose leaks are often repairable; outer-tub leaks are usually not.
• Noise and vibration: Belt, pulley, spring, or counterweight issues are commonly repairable.
• Electronics: A control board failure can be worth it if the washer is otherwise in good shape.

Repairs that are commonly “worth it” on this model

These are frequent, fixable problems on horizontal-axis washers like model 11042822202:

Symptom	Likely area	Example part for this model
Won’t drain, stops mid-cycle	Drain system	Water pump 280187
Won’t fill or fills slowly	Water supply and valve	Washer water inlet valve WP8181694
Door won’t lock, won’t start	Door latch system	Door lock WP8182634
Loud squeal or no tumble	Drive system	Washer drive belt WPW10388414
Water leaking at the door	Door seal	Bellow WP8181850

When replacement makes more sense

Replacement is the better call when you have one of these conditions:

• The outer tub is cracked or leaking at the bearing area.
• The washer has repeated failures across multiple systems (drain, fill, and control).
• You have severe corrosion, burning smells, or wiring damage that keeps returning.

Why it matters

A targeted repair (pump, inlet valve, door lock, belt, or bellow) can restore performance and prevent secondary damage like water leaks, mold odors, or a no-spin condition. Using the correct model-specific parts also reduces repeat breakdowns.

What to check first

Follow the troubleshooting and diagnostic steps in the 11042822202 owner’s manual before ordering parts; it helps you confirm symptoms, error behavior, and safe access steps.

Last updated: February 2026

On the Kenmore Elite washer model 11042822202, the F20 code points to a water inlet problem: the washer is not filling correctly (slow fill or no fill). Fixing it usually comes down to restoring proper water supply, flow, and inlet sensing; see the 11042822202 owner's manual for model-specific checks.

What to check first (fast, no tools)

• Confirm both hot and cold water supply valves are fully open.
• Make sure the fill hoses are not kinked, crushed, or frozen.
• Verify strong water flow at the wall by briefly removing a hose and running water into a bucket.
• Clean the inlet screen filters at the washer hose connections (sediment can restrict flow).
• Run a normal cycle again after restoring water flow.

Parts that commonly cause F20 on this model

If water supply is good but the code returns, these parts are common suspects on horizontal-axis Kenmore Elite washers:

• Washer water inlet valve WP8181694 (valve not opening fully or clogged internally)
• Flow meter WPW10110225 (washer not sensing incoming water correctly)
• Washer water-level pressure switch WPW10514214 (water level sensing issue)

Quick symptom-to-part guide

What you notice	Most likely area	What we do next
No water enters at all	Water supply or inlet valve	Check valves, screens; test/replace inlet valve
Water trickles in slowly	Screens/hoses, low pressure	Clean screens; verify household pressure
Water enters but code still appears	Flow sensing or level sensing	Check flow meter and pressure switch system

Why it matters

When the washer cannot fill at the expected rate, it can stop to prevent poor washing results and protect components from running without the correct water level.

Helpful DIY skill for this repair

If you plan to test electrical parts during troubleshooting, use our how to use a multimeter to test electrical parts video to get accurate readings safely.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For the Kenmore Elite horizontal-axis washer model 11042822202, reaching the high end of that range comes down to routine care, correct loading, and fixing small leaks or drain issues before they damage major components (use the 11042822202 owner's manual for the maintenance schedule and operating tips).

Typical lifespan and what affects it

Most washers fall into a similar life range, but these factors move the needle the most:

• Load size and balance: frequent overloading or unbalanced loads shorten bearing and suspension life
• Detergent use: too much HE detergent can cause oversudsing and extra strain on draining
• Water quality: hard water speeds up buildup in valves and hoses
• Moisture control: leaving the door closed traps moisture and can damage seals over time
• Early repairs: replacing a failing drain or fill part prevents secondary damage

Parts that commonly limit washer life

On a front-load style washer like this Kenmore Elite, these parts often show wear first:

Symptom you notice	Common wear area	Example part for this model
Won’t drain, water left in tub	Drain pump or drain path restriction	Water pump 280187
Slow fill, no fill, fill errors	Inlet valve or supply restriction	Washer water inlet valve WP8181694
Door won’t lock or cycle won’t start	Door lock/strike alignment or failure	Door lock WP8182634

Maintenance that helps you get 10 to 15 years

We recommend these habits for model 11042822202:

• Run a monthly cleaning cycle (or hot wash) and wipe the door area dry
• Use HE detergent and measure carefully
• Keep loads below “packed tight”; mix items to reduce out-of-balance spinning
• Check fill hoses for bulges or seepage and replace as needed
• If draining gets noisy or slow, address it early to protect the motor and controls

Why it matters

A washer usually fails early from cascading damage: a small leak, poor draining, or repeated unbalanced spins can stress the tub bearings, suspension, and electronic control. Preventive care and timely part replacement cost less than major tub or bearing repairs.

Last updated: February 2026

Your Kenmore Elite washer’s model number is printed on the appliance’s ID label. On Kenmore Elite front-load (horizontal-axis) washers like model 11042822202, the label is most often in the door opening (door jamb) or just behind the door; it can also be on the back or side of the cabinet.

Where to look on a Kenmore Elite front-load washer

Check these spots in order (they are the most common locations):

• Door opening: on the cabinet frame (door jamb) when you open the door
• Behind the door: around the inner rim area where the door closes
• Back of the control panel: on the rear surface behind the console
• Side of the cabinet: near the bottom edge of the main cabinet

What the model number looks like (and why it matters)

Kenmore Elite washer model numbers are typically a long number string. For this parts page, the model is 11042822202. Using the exact model number ensures we match the correct parts list, diagrams, and troubleshooting steps in the 11042822202 owner's manual.

Quick ID label checklist

• Write down the full model number exactly as shown
• Also record the serial number (helpful for production variations)
• Take a clear photo of the label before ordering parts

Common label locations by washer type

Washer type	Most common label location	Other common locations
Front-load (horizontal axis)	Door jamb / door opening	Back of console, side of cabinet
Top-load	Under lid or lid frame	Back of console, rear panel

Why it matters

Kenmore Elite washers can look similar across multiple model series, but parts like a door lock, water inlet valve, or water pump can vary by model. Matching the exact model number prevents ordering the wrong replacement part.

Last updated: February 2026

Kenmore Elite is a premium Kenmore product line that has been produced across multiple years (not a single “made in” year). For your Kenmore Elite washer model 11042822202, the most accurate way to pin down its production timeframe is to use the model and serial information and cross-check it with the identification details in the 11042822202 owner's manual.

How to date a Kenmore Elite washer like model 11042822202

We use the washer’s model and serial tag to determine the manufacturing date range.

• Unplug the washer before accessing the model and serial tag
• Look for the tag around the door opening, behind the door, or on the cabinet frame
• Write down the full model number (11042822202) and the full serial number
• Compare the serial format to the identification section in the 11042822202 owner's manual
• If the tag is damaged or missing, use the parts list to confirm key assemblies match your unit

What “Kenmore Elite” means (and what it does not)

“Kenmore Elite” identifies a higher-end feature set; it does not identify a single factory, a single manufacturer, or one specific year.

Common identifiers

Item	What it tells you	What it does not tell you
Model number (11042822202)	Series and configuration	Exact build date by itself
Serial number	Production date code	Parts compatibility by itself
Feature set (front-load, horizontal axis)	Design type	Exact year without serial

Why it matters

Knowing the approximate build date helps us match the correct replacement parts and revisions for your washer, especially for wear items like the water pump 280187 and the door lock WP8182634.

Last updated: February 2026