Kenmore Elite 66512782K311 undercounter dishwasher Parts

To identify your Kenmore dishwasher model, we recommend opening the door and looking for the model and serial tag on the inner door frame or along the tub opening. For this Kenmore Elite dishwasher, the model number format looks like 665.1277* or 665.1278* (your full model is 66512782K311). See the 66512782K311 owner's manual for the exact label locations and model format details.

Where to look on the dishwasher

Check these common spots first (in order):

• Inner door frame (left or right side of the door jamb)
• Top rim of the tub opening (visible when the door is open)
• Side wall of the tub near the front edge
• Behind the toe panel area (sometimes visible with a flashlight)

What the model tag looks like (and what to copy)

The tag usually includes multiple identifiers. Copy them exactly as shown.

• Model number (example: 66512782K311)
• Serial number (helps date the unit and match revisions)
• Type or manufacturing code (sometimes present)
• Electrical rating (useful for service checks)

Quick checklist: avoid common mix-ups

These issues cause the most wrong-part orders:

• Confusing the series (665.1277* / 665.1278*) with the full model number
• Missing the last characters (like K311) that identify a specific version
• Reading a faded tag; use a phone camera and zoom for clarity

Model number examples

What you see	What it means	What to use for parts
665.1278*	Model family/series format	Keep looking for the full model
66512782K311	Full model identifier	Use this for parts and diagrams
Serial number	Production identifier	Keep for reference

Why it matters

Kenmore dishwashers in the 665 series share many designs, but small model suffix changes can affect parts like the door latch, racks, or water inlet valve. Using the full model number helps match the correct diagrams and compatible replacement parts.

Last updated: January 2026

To hard reset the Kenmore Elite dishwasher model 66512782K311, we reset the control by canceling the current cycle: open the door to stop spraying, then press and hold CANCEL/DRAIN twice to reset the control, select a new cycle, and press START/RESUME. See the 66512782K311 owner's manual.

Hard reset steps (control reset)

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Open the door fully.
• Press and hold CANCEL/DRAIN until the Cancel/Drain light turns on.
• Press and hold CANCEL/DRAIN a second time (this resets the control).
• Select your new cycle and options.
• Press START/RESUME, then close the door.

If it still will not start after the reset

These checks solve most “won’t run” complaints on this Kenmore dishwasher.

• Close the door firmly until it latches.
• If the Start/Resume light is blinking, press START/RESUME and close the door within 3 seconds.
• Confirm the dishwasher has power (breaker not tripped, outlet working).
• Make sure large items are not preventing the door from closing.
• If water is standing in the tub, run CANCEL/DRAIN and let it drain fully.

What “hard reset” does (and does not do)

Action	What it does	What it does not do
Control reset (CANCEL/DRAIN twice)	Clears the current cycle and lets you restart from the beginning	Fix a failed latch, bad inlet valve, or drain pump
Cancel/Drain	Drains water left in the tub	Restore power if the breaker is tripped

Why it matters

A proper control reset clears a stuck cycle and gets the dishwasher back to a known starting point, which helps you confirm whether the issue is a simple cycle interruption or a part problem (like a latch or drain issue).

Last updated: January 2026

On Kenmore Elite dishwasher model 66512782K311, error code F2E2 points to a communication problem between the user interface (keypad) and the main electronic control board, so the dishwasher may not respond to button presses or may stop mid-cycle. See the troubleshooting and diagnostics section in the 66512782K311 owner’s manual.

What you’ll usually notice with F2E2

• Buttons do not respond, respond intermittently, or beep without starting
• Cycle lights act erratically or the display behaves inconsistently
• The dishwasher stops and drains, then shows the code
• Power cycling temporarily clears the code, but it returns

Quick checks we recommend first

1. Reset power: Turn off the breaker for 1 minute, then restore power.
2. Check the door is fully latched: A weak latch can mimic control issues. If the door will not latch consistently, inspect the dishwasher door latch WPW10653840.
3. Look for moisture or residue around the console area: Steam or detergent residue can affect the keypad.
4. Inspect visible wiring (with power off): Check for loose connectors at the control area and along the door harness path.

Likely causes and what typically fixes it

Likely cause	What it means	Typical fix
Keypad/user interface issue	Buttons or touch panel is not sending correct signals	Console or user interface service (model-specific)
Main control board issue	Control is not receiving or processing UI signals	Replace electronic control board
Loose or damaged harness/connector	Intermittent connection between UI and control	Reseat connectors; repair/replace harness

Why it matters

This code is not a wash motor or drain problem; it is an electronics communication fault. If the dishwasher cannot reliably read the keypad, it can fail to start, stop unexpectedly, or run the wrong cycle.

When to stop and call for service

• The code returns immediately after a reset
• You smell overheating plastic or see discoloration at connectors
• The dishwasher starts on its own or will not shut off normally

Last updated: January 2026

On the Kenmore Elite 66512782K311 dishwasher, the most common problems are no-start or stopping mid-cycle (door not fully latched or Start/Resume timing), not draining (hose kink or disposer knockout plug), poor cleaning from hard water buildup, and not drying well (rinse aid and heat-related issues). See the 66512782K311 owner's manual for model-specific troubleshooting steps.

Most common symptoms and what usually causes them

• Dishwasher does not run: door not closed and latched, Start/Resume not completed correctly, power issue (breaker/fuse)
• Water remains in tub or will not drain: kinked drain hose, food obstruction in drain/disposer, disposer knockout plug not removed
• Hard water residue or cloudy dishes: very hard water, not using rinse aid, not cleaning filters monthly
• Cycle runs too long: normal pauses during the cycle, incoming water not hot enough
• Not drying: rinse aid empty, water temperature too low, heater-related problem

Quick checks we recommend first (fast, no parts)

1. If Start/Resume is blinking, press START/RESUME and close the door within 3 seconds.
2. Confirm the door closes without interference from large dishes.
3. Check the home circuit breaker or fuse.
4. If it will not drain, inspect for a kinked drain hose and clear the disposer inlet.
5. For spotting and residue, verify incoming water is about 120°F (49°C) and use rinse aid.

When a part is commonly involved

Symptom	Common part involved	What it affects
Won’t fill or fills slowly	Dishwasher water inlet valve W11175771	Water entering the dishwasher
Water remains in tub	Dishwasher drain pump WPW10531320	Pumping water out
Not drying well	Heater W10703867	Heating water and supporting drying
Won’t start or stops when closing door	Dishwasher door latch WPW10653840	Confirms door is safely latched

Why it matters

Catching the root cause early prevents repeat wash failures and helps protect the wash system from hard-water mineral deposits. The manual also notes that extremely hard water can reduce cleaning performance and cause buildup, so routine filter cleaning and rinse aid use make a noticeable difference.

Last updated: January 2026