Whirlpool WGD70HEBW0 gas dryer Parts

Yes. For your Whirlpool gas dryer model WGD70HEBW0, searching by the full model number is the most accurate way to get compatible replacement parts because it filters the parts list and diagrams to the exact version of your dryer.

• Use the complete model number exactly as shown on the model tag: WGD70HEBW0
• Start with the parts list for your model, then narrow by section (drum, blower, burner, controls)
• Match the part description to what you see on the dryer (for example, roller, igniter, thermistor)
• Confirm the part ID before ordering to avoid look-alike parts
• Use the troubleshooting and maintenance steps in the owner's manual to confirm symptoms before replacing parts

If you already know the symptom, these are frequently replaced items for this Whirlpool gas dryer:

• Igniter 279311 (no heat, burner will not ignite)
• Dryer gas valve coil kit WPW10328463 (ignites once then stops heating, intermittent heat)
• Dryer thermistor WP8577274 (temperature sensing issues, overheating or poor drying)
• Dryer blower wheel WP697772 (weak airflow, loud vibration, long dry times)
• Dryer drum support roller WPW10314173 (thumping or rumbling while tumbling)

Use this checklist to make sure the part you pick matches your dryer and your repair:

• Model number matches: WGD70HEBW0
• Symptom matches the part’s job (heat, airflow, tumbling, controls)
• You are replacing related wear items together when it makes sense (rollers, shafts, washers)
• You have the right tools and access for the repair
• You follow gas-safety and installation steps from the installation guide

Whirlpool dryers often have multiple versions that look the same but use different brackets, sensors, or control parts. Searching by WGD70HEBW0 keeps you aligned with the correct diagrams and OEM-fit parts, which reduces returns and repeat repairs.

Last updated: February 2026

On your Whirlpool gas dryer model WGD70HEBW0, the fastest way to get the right part number is to first find the model and serial tag, then use that exact model number to look up the correct parts list. For this style dryer, the rating plate is typically in the door opening (door well).

Check these common locations on Whirlpool dryers (start with the door opening):

• Door opening (door well) on the cabinet frame; look for a rating plate sticker
• Inside the door edge area (near the latch side)
• Rear panel of the dryer cabinet (less common on this style)
• Behind the lower access panel (if your model has one)

If you are confirming gas type during parts lookup or installation, the installation information notes that burner and gas type details are on the rating plate in the door well. Use that same plate to capture the full model number.

There are two numbers people commonly call a “part number”:

• Copy the model number exactly, including all letters and numbers (for example, WGD70HEBW0).
• Use the model number to select the correct diagram section (drum, blower, burner, controls).
• Match the part by name and part ID, not just by appearance.
• If you are troubleshooting a noise issue, common wear items include rollers and idler components; a kit such as the dryer repair kit 4392067 can cover multiple wear parts at once.
• For heating problems on a gas dryer, common suspects include the igniter, radiant sensor, and gas valve coils; confirm symptoms before replacing parts.

Whirlpool often uses similar-looking parts across multiple dryer series. Using the rating plate model number first prevents mismatches in drum support parts, burner components, and electronic controls.

For diagrams and model identification details, use the owner's manual.

Last updated: February 2026

Common problems on Whirlpool gas dryers like model WGD70HEBW0 include no heat, long dry times, drum not turning, loud squealing or thumping, and the dryer not starting. Most of these issues trace back to airflow restrictions (lint and venting), worn drum support parts, or burner and temperature-sensing components; see the installation guide for setup checks that affect performance.

• Dryer will not start: door not fully closed, power supply issue, or a failed control component
• No heat or weak heat: burner ignition problem (igniter, radiant sensor, gas valve coils) or a safety cut-off opening
• Takes too long to dry: clogged lint screen, crushed/kinked vent, long vent run, or blower wheel issues
• Loud noise (squeal, rumble, thump): worn drum rollers, idler pulley components, or blower wheel damage
• Drum not turning: drive system wear (belt/idler/motor related)

• Clean the lint screen and confirm strong airflow at the outside vent hood.
• Inspect the vent duct for crushing, kinks, or heavy lint buildup.
• Run a Timed Dry heated cycle (not Air Only) and confirm the dryer starts and heats.
• For gas models, confirm the gas supply is on and the flexible gas line is not kinked.
• Make sure the dryer is level; an uneven floor can affect tumbling and sensor cycle performance.

If troubleshooting points to a failed component, these are common fixes for this model:

Airflow and heat problems do more than slow drying; they can overheat the dryer and repeatedly trip safety devices. Keeping the venting clear and replacing worn support parts early helps the dryer run quieter, dry faster, and reduce strain on the drive motor and burner system.

• If your dryer is showing a code, use our Whirlpool duet dryer error codes guide to match the code to likely causes and next steps.

Last updated: February 2026

Whirlpool dryers typically last 10 to 13 years. With good airflow, correct installation, and routine cleaning, many reach the upper end of that range; chronic overheating from restricted venting and heavy daily use are the most common reasons a dryer wears out sooner.

• Vent restriction (long runs, too many elbows, crushed duct) increases heat and run time
• Lint buildup in the lint screen housing, blower area, or venting reduces airflow
• Overloading strains the drive system and drum support components
• Heat-related cycling issues can stress sensors and safety thermostats
• Installation conditions (unlevel floor, cold spaces below 40 F) can affect cycle performance

Use these habits to help your Whirlpool gas dryer run cooler and longer; our installation guide includes venting limits that protect performance.

• Clean the lint screen every load
• Inspect and clean the vent line and exterior hood regularly
• Keep the vent path as straight as possible; use rigid metal venting when you can
• Avoid packing the drum tight; leave room for tumbling
• If drying times increase, address airflow first before replacing parts

A dryer that runs with poor airflow operates hotter and longer per load; that shortens the life of key components (motor, rollers, sensors) and increases energy use. Keeping venting within the recommended limits is one of the simplest ways to extend service life.

Last updated: February 2026