Kenmore Elite 66514743N513 dishwasher Parts

To hard reset the Kenmore Elite dishwasher model 66514743N513, we reset the control by pressing and holding CANCEL/DRAIN until the Cancel/Drain light turns on, then closing the door so it drains and clears the cycle (about 2 minutes). For a full control reset during a cycle restart, we use the reset sequence in the 66514743N513 owner's manual.

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Press and hold CANCEL/DRAIN until the Cancel/Drain light turns on.
• Close the door to start the drain (if water is in the bottom).
• Wait about 2 minutes for the drain to finish and the light to turn off.
• Select a new cycle and press START/RESUME; close the door within 3 seconds.

Use this when the dishwasher is stuck mid-cycle or you want to fully restart the program:

• Open the door and wait for spraying to stop.
• Press START/RESUME.
• Press and hold CANCEL/DRAIN twice to reset the control.
• Re-select your cycle and options.
• Press START/RESUME and close the door within 3 seconds.

A “hard reset” on this Kenmore dishwasher is really a control cancel and drain. It clears the current cycle logic, helps the unit drain standing water, and lets you start a fresh cycle without guessing which buttons to press.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66514743N513, error code F2E2 points to a keypad or user interface problem, most often a communication failure between the console (touchpad) and the main control. Clearing power may restore operation temporarily, but the underlying issue usually needs diagnosis.

• Reset power: turn the dishwasher off at the breaker for 1 minute, then restore power.
• Make sure no keys are stuck; wipe the console dry and press each key once.
• If the dishwasher is unresponsive, try a different cycle selection and press Start.
• If the code returns quickly, focus on the console and control connections.
• Review any model-specific reset or diagnostic steps in the 66514743N513 user manual.

In Kenmore 665-series style dishwashers, F2E2 is commonly tied to the user interface circuit. Typical causes include:

• Moisture intrusion into the console area
• A failing console (user interface) or touchpad
• A loose or oxidized ribbon/connector between the console and control
• A failing electronic control board (less common than console issues)

If the code persists after a reset and basic checks, these parts are commonly inspected during service:

If your dishwasher also has door-closing issues (won’t start unless you push hard), inspect the latch because a poor door close can mimic control problems. The Dishwasher door latch WPW10653840 is a common wear item on this platform.

When the console and main control cannot communicate reliably, the dishwasher may stop mid-cycle, refuse to start, or run with incorrect selections. Addressing F2E2 early helps prevent repeated cycle failures and protects the control components.

Last updated: January 2026

Kenmore Elite dishwashers are typically designed to run quietly, and many Kenmore Elite 24-inch built-in models are rated around 42 dBA. For your Kenmore Elite 66514743N513, we recommend confirming the exact sound rating in the 66514743N513 owner's manual.

Dishwasher noise is measured in decibels A-weighted (dBA); lower numbers sound quieter in a kitchen.

• 39 to 44 dBA: very quiet; you may barely notice it running
• 45 to 50 dBA: quiet; normal conversation usually covers it
• 51 to 55 dBA: moderate; you will hear wash and drain more clearly
• 56+ dBA: louder; common in older or basic models

A quiet-rated dishwasher can get noisier when something changes in loading, water flow, or moving parts.

• Make sure spray arms spin freely and are not hitting tall items
• Reposition lightweight plastics so they do not rattle
• Check the racks for worn rollers or loose hardware
• Clean the filter area regularly to prevent pump strain
• Verify the unit is secured and level (movement can amplify noise)

If the noise is coming from the rack movement (clicking, grinding, or jumping), the dishwasher rack adjuster W10712395 is a common wear item on many Kenmore 665-series designs.

Noise rating is a good indicator of day-to-day comfort, but real-world loudness also depends on installation, leveling, and rack and pump condition.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66514743N513, the F4E1 service code points to a wash motor (circulation pump motor) problem, meaning the dishwasher is not moving water through the spray arms correctly. After the repair, clear the code using the reset steps in the 66514743N513 owner's manual.

• Dishes come out dirty because spray pressure is weak or stops
• You may hear a hum, grinding, or intermittent motor sound
• The cycle may stall, drain, or end early
• Error returns soon after restarting

1. Power reset: Turn off the breaker for 1 minute, then restore power.
2. Loading and spray arms: Make sure tall items are not blocking spray arm rotation.
3. Filter and sump area: Clean debris that can restrict circulation.
4. Water temperature: Aim for about 120°F at the sink; low temp can worsen wash performance.

In many Kenmore 665-series designs, F4E1 is resolved by repairing the wash motor circuit or replacing the pump/motor components that drive circulation.

If you’re already diagnosing a motor issue, the pump motor is a common suspect; for this model, a related component is the dishwasher pump motor W11084656.

Use the model’s keypad sequence to clear stored faults and exit diagnostics. Follow the exact button pattern and timing in the 66514743N513 owner's manual so the dishwasher returns to normal operation.

When the circulation motor cannot run correctly, the dishwasher may still fill and drain, but it cannot maintain spray pressure. That leads to repeat error codes, poor cleaning, and longer cycle interruptions.

Last updated: January 2026