Kenmore 11072702101 gas dryer Parts

For a Kenmore dryer, replacing a heating element typically costs $20 to $120 for the part if you do it yourself, and about $150 to $350 total if you hire service (part plus labor). For your Kenmore gas dryer model 11072702101, “no heat” problems are often caused by gas-heat components rather than an electric heating element; use the 11072702101 installation guide to confirm your dryer type and setup.

What you are usually paying for

A “heating element” price depends on whether you are buying only the heater or a complete assembly.

• Part only (common range): $20 to $120
• Assembly or kit (common range): $80 to $200
• Labor (typical service call plus repair): $100 to $250
• Total installed cost (typical): $150 to $350

Gas vs. electric: why this matters on model 11072702101

Model 11072702101 is a gas dryer, so it heats with a burner system. If the dryer tumbles but does not heat, the most common repair cost is tied to ignition and gas valve parts, not an electric heater.

Dryer type	What makes heat	Common “no heat” parts	Typical part-cost impact
Electric dryer	Heating element	Heater, thermostats	Often “heating element” is the right part
Gas dryer (11072702101)	Burner and igniter	Igniter, coils, radiant sensor	Often cheaper than a full heater assembly

Parts that commonly fix “no heat” on this Kenmore gas dryer

If your dryer runs but will not heat, these model-matched parts are common fixes:

• Dryer valve coil kit 279834 (gas valve coils)
• Whirlpool dryer burner igniter kit 279311 (igniter)
• Dryer radiant sensor WP338906 (flame sensing)
• Dryer gas valve WP8318277 (less common, higher cost)

Cost-saving checks before you buy parts

These steps prevent repeat failures and reduce drying time.

• Clean the lint screen and check airflow at the outside vent hood
• Inspect the vent for crushing, kinks, or long runs
• Confirm the dryer is set to a heat cycle (not air fluff)
• Verify the gas supply shutoff valve is fully open
• If heat starts then stops, suspect coils or sensor first

Why it matters

Misidentifying a gas-dryer heating problem as an “element” replacement can lead to buying the wrong part and paying labor twice. Matching the symptom to the burner system parts is the fastest path to restoring heat.

You can order replacement parts for model 11072702101 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

For Kenmore gas dryer model 11072702101, a hard reset is simple: disconnect power for about 1 to 5 minutes, then restore power and try starting a cycle again. This clears many temporary control and cycle glitches; then confirm the door is fully closed and the cycle is selected before pressing PUSH TO START (see the 11072702101 owner's manual).

Hard reset steps (safe, quick)

• Turn the cycle selector to OFF.
• Unplug the dryer (or switch the dryer breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door firmly.
• Select a cycle and temperature.
• Press PUSH TO START.

If it still will not start after the reset

These checks come straight from the startup and troubleshooting guidance for this model.

• Confirm the dryer is plugged into a grounded 3-prong outlet.
• Check the home electrical supply; many dryers use two fuses or two breakers, so verify both are on.
• Make sure the dryer door is closed and latching correctly.
• Verify the vent is not crushed or kinked (a bad vent can contribute to overheating and shutdowns).
• If the dryer starts only with the door held or slammed, test the door switch; replace the dryer door switch WP3406107 if it is not consistently making contact.

What “resetting” does (and does not) fix

A hard reset helps when the dryer is stuck in a cycle state or the controls are acting erratically. It does not fix a failed start circuit or a mechanical failure.

Symptom	What to try next	Common part to check
Nothing happens when you press start	Verify power, door closed, cycle not set to OFF	Dryer door switch WP3406107
Motor hums but drum will not turn	Inspect belt and drum support components	Dryer drum belt 341241
Dryer runs but airflow is weak	Clean lint screen and vent path	(venting, lint buildup)

Why it matters

Resetting is the fastest way to clear a false “no-start” condition, but confirming power, door closure, and venting prevents repeat shutdowns and protects key components like the motor and timer.

You can order replacement parts for your Kenmore 11072702101 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

On your Kenmore gas dryer model 11072702101, a bad start switch shows up as a no-start condition when you press PUSH TO START, or the dryer only runs while you keep the button pressed. Confirm it by testing the switch for continuity with power disconnected.

Symptoms that point to a bad start switch

• Dryer has power but does nothing when you press PUSH TO START
• Dryer starts only while the button is held in
• Button feels sticky, loose, or does not click consistently
• Intermittent starting (works sometimes, fails other times)

Quick checks first (rule out common no-start causes)

Before you open the console, follow the start and restart steps in the 11072702101 owner's manual and verify:

• Dryer is plugged into a grounded 3-prong outlet
• House fuse is good and breaker is not tripped
• Door is fully closed (a bad door switch can mimic a bad start switch)
• Cycle is set to a timed cycle (not pointing to OFF)

How to test the start switch with a multimeter

1. Unplug the dryer (or shut off power at the breaker).
2. Access the push-to-start switch in the console.
3. Remove at least one wire from the switch terminal.
4. Set the meter to continuity or lowest ohms.
5. Check readings with the button not pressed and pressed.

Button position	Expected reading	What it means if different
Not pressed	Open (no continuity)	If closed: switch stuck closed
Pressed	Closed (continuity, near 0 ohms)	If open: switch failed open

Why it matters

The start switch is a momentary contact that completes the motor start circuit. If it cannot close when pressed, the motor never gets the “start” signal, even when power and door switch are OK.

Parts and next steps

If the switch tests bad, replace it with the exact start switch listed for model 11072702101. If it tests good, check the door switch circuit (see dryer door switch WP3406107) and then the motor circuit.

You can order parts from the model parts list, or search by model number on Sears PartsDirect.

Last updated: February 2026