Kenmore 11079422801 dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label. On model 11079422801, that label is typically in the door opening (door well) on the cabinet frame, or on the back of the dryer near the top. See the 11079422801 owner’s manual for label wording and record-keeping.

Where to look on Kenmore model 11079422801

Check these common label locations first:

• Inside the dryer door opening on the cabinet frame (door well)
• On the back panel near the top edge
• Along the side of the door opening (near the latch area)
• Occasionally behind the lower front access panel (if equipped)

What the model number label looks like

The label usually includes both a model number and a serial number. For parts lookup and diagrams, we use the model number.

Label item	What it’s used for	Example format
Model number	Finding correct parts and manuals	11079422801
Serial number	Identifying production details	Letters and numbers

Tips to avoid mix-ups

Kenmore model numbers can be easy to misread. Before ordering parts or troubleshooting, we recommend:

• Copy the model number exactly as printed (all digits)
• Take a clear photo of the label for reference
• Double-check for swapped digits (common when handwriting)
• Use the full model number, not just “Kenmore 110”

Why it matters

Kenmore dryers often share similar styling across multiple model numbers, but internal components (like the drive belt, door switch, or gas burner parts) can differ. Using the exact model number helps ensure the right diagrams, repair steps, and compatible replacement parts.

Last updated: January 2026

For Kenmore dryer model 11079422801, the most reliable “hard reset” is a power reset: turn the dryer off, unplug it (or switch the breaker off), wait 1 minute, then restore power and start a new cycle. This model uses a mechanical timer, so there is no special button sequence reset.

Reset steps for model 11079422801

• Turn the cycle selector to OFF.
• Unplug the dryer (or turn the breaker off).
• Wait 60 seconds (up to 5 minutes is fine).
• Restore power.
• Close the door, select a cycle, and press PUSH TO START.

For normal operation details (stopping and restarting, cycle selection), see the 11079422801 use & care manual.

If it still will not start after a reset

A reset will not fix an open safety circuit or a power supply issue. Check these common causes:

• Door not fully closed or a failed door switch
• Blown house fuse or tripped breaker (some dryers use two fuses/breakers)
• Timer not set to a runnable position
• Failed start switch
• Motor problem (hums but will not run)

Quick part checks (when symptoms match)

Symptom	Most likely check	Example compatible part
No response when pressing start	Start switch	Dryer push-to-start switch WP3977456
Runs only with door held shut	Door switch	Door switch WP3406105

If the dryer runs but shuts off or will not heat

This model is a gas dryer; airflow problems can contribute to overheating and shutdowns. After a power reset, also:

• Clean the lint screen
• Check the vent path for crushing, kinks, or lint blockage
• Confirm the outside exhaust hood opens freely

If you suspect a safety device has opened, use the parts list for this model to choose the correct replacement. One example safety component listed for this model is the dryer thermal cut-off kit W11050897.

Why it matters

A “hard reset” clears temporary control states, but most dryer no-start and no-heat problems come from power supply issues, door safety circuits, or restricted venting. Correcting the root cause helps prevent repeat shutdowns and improves drying performance.

Last updated: January 2026

PF on a Kenmore dryer (including model 11079422801) stands for power failure. It means the dryer’s electrical power was interrupted during a cycle, so the cycle stopped and the control is alerting you that power was lost; see the 11079422801 user manual.

What to do when you see PF

• Press Pause/Cancel (or turn the cycle selector to Off) to clear the display.
• Re-select your cycle and press Push to start to restart.
• Check that the dryer is plugged in firmly and the outlet is working.
• Check your home’s breaker or fuses; many dryers use a dedicated circuit.
• If PF returns repeatedly, avoid using an extension cord or power strip.

Common causes

Cause	What it looks like	What to check
Brief outage or flicker	PF appears once after a storm	Restart cycle
Loose plug or outlet	PF happens when the dryer vibrates	Outlet fit, cord seating
Tripped breaker or blown fuse	Dryer won’t run or stops mid-cycle	Reset breaker/replace fuse
Power drop from overloaded circuit	PF repeats with other appliances running	Use a dedicated circuit

Why it matters

A PF message is usually not a dryer failure; it is the dryer protecting the load and letting you know the cycle was interrupted. If power is unstable, drying results can be inconsistent and repeated interruptions can point to a household electrical issue.

When a part might be involved

PF is typically power-related, not a worn part. If the dryer will not start after clearing PF and confirming power, a failed start circuit component can be a possibility; for example, the dryer push-to-start switch WP3977456 is one item we commonly check on this style of Kenmore dryer.

Last updated: January 2026