Kenmore 11096591240 electric dryer Parts

Your Kenmore dryer’s model number is printed on the appliance’s ID label; for this page, the model is 11096591240. Check the label inside the door opening first, then the back panel or the cabinet frame near the lint screen housing.

Look in these common spots on Kenmore electric dryers:

• Inside the dryer door opening on the cabinet frame
• On the back panel of the dryer
• Along the door opening edge (hinge side or latch side)
• Near the lint screen opening (on the housing or nearby cabinet surface)
• On the lower front frame area behind the door

Kenmore model numbers are usually a long string of numbers (sometimes with a dot in other Kenmore lines). The exact model number is what we use to match the correct parts, wiring, and component fit for your dryer.

Before you buy a replacement part, we recommend:

• Copy the model number exactly as printed (include every digit)
• Take a clear photo of the label for reference
• Match the part by function and symptom (heat, noise, won’t start)
• Compare your old part’s markings to the listing when possible

If you’re troubleshooting while identifying the model, common heat-related failures on electric dryers involve the heating circuit (for example, a failed heater or safety fuse). For model 11096591240, examples of commonly replaced parts include the dryer heating element WP3387747 and the dryer thermal fuse WP3390719.

Kenmore dryers often share a similar look across many model numbers, but internal components like the heating element, thermostat, belt drive parts, and door switch can vary by model. Using the exact model number prevents fit issues and repeat repairs.

Last updated: February 2026

A Kenmore electric dryer like model 11096591240 typically lasts 13 years with normal household use and good airflow. Keeping the lint path clear and fixing heat or drum-noise issues early helps you reach that lifespan.

• Vent restriction (long runs, crushed flex vent, clogged hood)
• Overheating from poor airflow (can trip safety devices)
• Wear parts aging (belt system, drum support, blower wheel)
• Electrical stress (loose power connections, cycling issues)
• Load habits (overloading strains the motor and drum)

• Clean the lint screen every load; replace a damaged screen like screen W10120998.
• Vacuum lint from the lint housing and blower area periodically.
• Confirm strong airflow outside while the dryer runs.
• Avoid overloading; dry similar fabrics together.
• Address “no heat” or “runs then stops” symptoms promptly; a common safety part is the dryer thermal fuse WP3390719.

Most “short lifespan” complaints trace back to overheating and airflow problems. Good venting reduces heat stress on the heating circuit, thermostats, and motor so the dryer can run reliably for years.

Last updated: March 2026

For Kenmore electric dryer model 11096591240, the most commonly replaced parts are the heating and safety components (no heat or shuts off) and drum drive parts (noise or no tumble). We recommend matching symptoms to the correct part before ordering.

• No heat or weak heat: dryer heating element WP3387747, thermostats, or a cut-off.
• Dryer won’t start or stops: dryer thermal fuse WP3390719 or a door-related switch.
• Squealing or thumping: dryer idler pulley 279640 and other drum support components.
• Poor airflow or rattling: dryer blower wheel WP697772.
• Door won’t stay closed: door strike and latch components.

• Clean lint screen and confirm strong outside exhaust airflow.
• Verify the dryer is getting full power (electric dryers need proper 240V supply).
• If it runs but does not heat, test the heating circuit parts with a meter.
• If it hums but will not tumble, inspect the belt path and idler area.

Replacing the right part the first time restores drying performance and prevents repeat failures. For example, a blown thermal fuse often points to a vent restriction, so correcting airflow helps protect the new fuse and the heating system.

Last updated: March 2026