Kenmore 11076712690 gas dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number plate; for model 11076712690, that plate is the official identifier you’ll use to match the correct parts, wiring, and operating instructions. Record both the model and serial numbers for future service and parts lookups.

Where to find the model number plate

Check these common locations on Kenmore gas dryers:

• Inside the dryer door opening (door jamb area)
• On the cabinet frame just behind the door
• On the back panel of the dryer
• Near the lint screen housing (some designs)

For the exact location and how it’s labeled, use the 11076712690 owner's manual.

What to write down (and why)

When you find the plate, copy the information exactly as shown.

• Model number (example: 11076712690)
• Serial number (unique to your dryer)
• Date of purchase (helpful for maintenance records)

Quick reference

Item	What it tells you	Used for
Model number	The exact dryer design and parts list	Ordering parts like a door switch or thermostat
Serial number	Production details for your specific unit	Service history, verifying correct revisions

Why it matters

Kenmore model prefixes (such as 110 or 796) can point to different manufacturers and designs, and small design changes affect which parts fit. Using the full model number from the plate helps ensure you get the right replacement parts the first time.

Last updated: February 2026

The most common problems we see with the Kenmore 11076712690 gas dryer are no heat, long dry times, won’t start, drum not turning, and loud noise. These issues usually trace to airflow restrictions, ignition components, or drum drive and support wear.

Top symptoms and what usually causes them

• No heat: failed igniter, radiant sensor, gas valve coils, or high-limit thermostat
• Heats then stops: overheating from poor venting, cycling thermostat issues
• Long dry times: clogged venting, lint chute leaks, weak blower wheel
• Won’t start: door switch problem, timer/contact issue, wiring problem
• Drum won’t turn: broken belt, worn idler pulley, seized drum support, motor issue
• Squealing/thumping: drum support/bearing surfaces, roller shafts, baffles

Quick checks before replacing parts

Follow the diagnostic flow in the 11076712690 owner's manual, then:

• Confirm strong airflow at the outside vent hood
• Clean lint screen and check for lint buildup in the lint chute area
• Listen for ignition sequence (click, glow, flame) on a heat cycle
• Check the door closes firmly and the switch clicks
• If the motor hums but drum does not move, inspect the belt and idler

Parts commonly involved (this model)

Problem	Part to consider	Part ID
No heat (ignition)	Igniter 279311	279311
No heat (flame sensing)	Dryer radiant sensor WP338906	WP338906
No heat (gas valve coils)	Dryer valve coil kit 279834	279834
Drum not turning	Drum belt 341241	341241
Long dry times/noisy airflow	Dryer blower wheel WP694089	WP694089
Overheating/shuts off	Dryer high-limit thermostat W11050897	W11050897

Why it matters

Gas dryer heat complaints are often caused by airflow problems first; fixing venting and lint buildup prevents repeat failures of thermostats, sensors, and gas ignition parts.

Last updated: March 2026

A Kenmore gas dryer like model 11076712690 typically lasts 13 years with normal household use. Keeping airflow strong (lint screen and venting) and fixing wear items early helps this dryer reach its full service life.

What affects lifespan most

• Vent restriction (long runs, crushed flex duct, clogged wall cap)
• Overheating from lint buildup in the blower housing or lint chute
• Worn drum support parts that strain the motor
• Ignition and heat-control parts cycling excessively
• Heavy loads and frequent back-to-back cycles

Maintenance that adds years

Use the schedule in your 11076712690 owner's manual as your baseline, then follow these best practices:

• Clean the lint screen every load
• Inspect and clean the vent line regularly (especially if dry times increase)
• Avoid overloading; it wears the belt and drum supports
• Stop using the dryer if you smell burning or hear loud squealing
• Replace common wear parts before they damage other components

Common wear parts to watch

Symptom	Likely wear area	Example part for this model
Drum not turning, motor runs	Belt or idler system	Drum belt 341241
Squealing or thumping	Drum support/bearing surfaces	Bearing and shaft components (varies by symptom)
Long dry times, hot cabinet	Airflow path and thermostats	Lint chute seals, thermostats

Why it matters

A dryer that runs hot or struggles to move air wears out faster and can damage key components like the drive motor, thermostats, and gas ignition system. Preventive cleaning and timely part replacement usually costs less than a major breakdown.

Last updated: March 2026