Kenmore Elite 66517262402 dishwasher Parts

To turn off Control Lock on your Kenmore Elite dishwasher model 66517262402, press and hold HEATED DRY for 4 seconds until the LOCK ON light turns off. If the light flashes when you press buttons, the controls are still locked; repeat the 4-second hold.

Quick unlock steps (model 66517262402)

• Make sure the dishwasher door is closed (it can be opened while locked, but unlocking is easier with it closed).
• Press and hold HEATED DRY for 4 seconds.
• Confirm the LOCK ON indicator turns off.
• Press START/RESUME to continue a cycle if it was paused.
• If you were using a delay, press CANCEL/DRAIN to clear it, then reselect your cycle.

What the LOCK ON light and button behavior mean

What you see	What it means	What to do
LOCK ON is lit solid	Controls are disabled	Hold HEATED DRY 4 seconds to unlock
Light flashes 3 times when you press a pad	Dishwasher is locked	Hold HEATED DRY 4 seconds
Door opens but buttons do nothing	Normal when locked	Unlock, then press START/RESUME

If it keeps re-locking or won’t respond

• Reset power: turn the dishwasher off at the breaker for 1 minute, then restore power.
• Check for a stuck key: press each keypad once to ensure none feel jammed.
• If START/RESUME is flashing, close the door fully and press START/RESUME (on some top-control models, press it again if the door was not closed within a few seconds).
• Review the control lock section in the owner's manual.

Why it matters

Control Lock prevents unintended cycle changes and button presses during a wash. Unlocking it restores normal keypad operation so you can select cycles, options, and start or resume cleaning.

Last updated: February 2026

To clear most indicators and reset the cycle on your Kenmore Elite dishwasher model 66517262402, press CANCEL/DRAIN and let the dishwasher complete the drain (about 2 minutes). This clears selected cycles and options so you can start fresh; see the steps in the owner's manual.

Quick reset steps (clears indicators and cancels a cycle)

• Press CANCEL/DRAIN once.
• Keep the door closed so the unit can drain.
• Wait about 2 minutes for the drain to finish.
• If you want to stop draining early, press CANCEL/DRAIN again.
• Select a new cycle and any options.
• Press START/RESUME to begin.

If the START/RESUME light is flashing

This usually means the door was opened mid-cycle or power was interrupted.

• Close the door fully and latch it.
• Press START/RESUME to continue.
• On top-control models, if the door is not closed within a few seconds after pressing Start/Resume, press START/RESUME again.

What “clearing” does (and does not) do

What you see	What the reset does	What to do next
Cycle/options lights still selected	Clears selections when you press CANCEL/DRAIN before starting	Re-select cycle/options, then START/RESUME
Unit stuck mid-cycle	Cancels the cycle and drains water (if needed)	Start a new cycle after draining
“Clean” light flashing	Indicates a malfunction (commonly heater circuit related)	Cancel/drain, then troubleshoot before running again

Why it matters

Clearing indicators the right way prevents starting a new wash with the wrong cycle, detergent settings, or water still in the tub. Letting the 2-minute drain finish also helps avoid poor cleaning and standing water issues.

For code-specific troubleshooting, use Kenmore 665 model dishwasher error codes.

Last updated: February 2026

On a Kenmore Elite dishwasher model 66517262402, error code F2E2 points to a keypad or user interface (UI) communication problem, meaning the control is not reading the button presses correctly or is not communicating cleanly with the main control.

What to do first (quick reset and checks)

• Press Cancel/Drain (if your model has it) and let the dishwasher attempt to drain.
• Turn power off at the breaker for 1 minute, then restore power.
• Close the door fully; then press START/RESUME to see if the cycle resumes (a flashing Start/Resume light commonly relates to the door being opened or power being interrupted).
• If the code returns immediately, avoid repeatedly pressing keys; that can make diagnosis harder.
• Review the control and indicator behavior in the owner's manual.

Common causes of F2E2 on Kenmore 665 dishwashers

F2E2 is most often triggered by one of these conditions:

• A stuck key on the keypad (button feels jammed or stays “pressed”)
• Moisture or residue affecting the UI (especially around the console)
• A loose or oxidized connection between the UI and main control
• A failing UI assembly or electronic control

Basic symptom guide

What you notice	What it usually means	What to try
Buttons beep but don’t respond	Keypad not being read	Power reset; check for stuck keys
Random beeping or changing cycles	Keypad shorting or moisture	Let console dry; reset power
Code returns right after reset	Hard fault in UI/control	Plan for inspection/repair

Why it matters

When the UI cannot reliably communicate with the main control, the dishwasher may not start, may stop mid-cycle, or may not let you select options. Fixing the UI communication issue restores normal cycle selection and dependable operation.

Last updated: February 2026

To drain your Kenmore Elite dishwasher model 66517262402, press CANCEL/DRAIN with the door fully closed. The dishwasher will run a drain cycle for about 2 minutes (if needed) and then stop automatically. Press CANCEL/DRAIN again to stop draining early.

Quick steps to force a drain

• Close the dishwasher door completely (it will not drain with the door open).
• Press CANCEL/DRAIN once.
• Wait about 2 minutes for the drain cycle to finish.
• If you need to stop the drain, press CANCEL/DRAIN again.
• Before starting a new wash cycle, use CANCEL/DRAIN to clear the previous cycle and options.

If it still will not drain

These checks fix most “won’t drain” complaints on 665-series Kenmore dishwashers.

• Check the sink/disposer connection: If you have a garbage disposer, make sure the disposer inlet knockout plug was removed.
• Inspect the drain hose routing: The drain connection must be before the drain trap and the hose should be looped up and secured under the counter (a high loop helps prevent backflow).
• Look for kinks or pinches: Make sure the drain hose is not crushed behind the unit.
• Check for a clogged air gap (if installed): A blocked air gap can stop draining or cause slow draining.
• Verify the drain hose connection and clamp: The hose should be pushed fully onto the connector and clamped in place.

Drain setup requirements (installation basics)

Item to verify	What “correct” looks like	Why it matters
Drain connection height	At least 20 in. (50.8 cm) above the floor	Helps prevent dirty water from flowing back into the tub
Connection location	Before the drain trap	Prevents siphoning and slow drains
Hose routing	High loop under the counter, no kinks	Improves drain performance and reduces backups

Why it matters

A proper drain cycle and correct drain hose routing protect the circulation system, prevent standing water odors, and reduce the chance of sink water backing up into the dishwasher.

For model-specific button behavior and cycle details, follow the steps in the 66517262402 owner's manual. For correct drain hose routing and connection height, use the installation guide.

Last updated: February 2026

Your Kenmore Elite dishwasher model number is printed on the model and serial number label located inside the door area of model 66517262402. Open the door and look along the inner door frame or tub edge for a rating label that lists both the model and serial number.

Where to find the model and serial number label

On Kenmore Elite dishwashers like model 66517262402, the label is placed where it stays readable but protected from daily use.

• Open the dishwasher door fully.
• Check the inner door frame (left and right sides).
• Look along the tub opening edge near the front.
• Find a label that includes Model and Serial.
• Write the numbers down exactly as shown.

For a diagram showing the label location in the parts and features section, use the owner's manual.

What the model number looks like for this dishwasher

This dishwasher is part of the Kenmore 665 series; the full model number is typically shown with a prefix format in the manual (for example, 665.1726 followed by additional digits for color/variant). Your complete model number on the label should match 66517262402.

What you see	What it means
665.1726…	Model family/series shown in the manual
66517262402	Full model number used to match exact parts
Serial number	Unique ID for your specific unit

Why it matters

Using the exact model number ensures we match the correct dishwasher parts and diagrams for your unit, especially for fit-critical items like the dishwasher water inlet valve WP8531669 or the heater element WPW10082892.

Last updated: February 2026