Kenmore 11026902692 washer Parts

Your Kenmore washer model number is printed on the model and serial number plate; for model 11026902692, use that exact number when looking up parts and documentation so you get the correct fit and instructions. The owner's manual also explains where to record the model and serial numbers.

On Kenmore washers like 11026902692, the model and serial number plate is typically located in one of these common spots:

• Under the washer lid (top-load models)
• Around the lid opening or on the underside of the lid
• On the back of the cabinet near the power cord entry
• Along the rear edge of the control console area

Model numbers must match exactly, character for character. Use these tips to avoid mix-ups:

• Write it down exactly as shown (including all digits)
• Do not use only the first few digits (for example, use 11026902692, not just “110”)
• Record the serial number too; it helps confirm production details when ordering parts
• If the label is worn, take a clear photo and zoom in to verify each digit

Kenmore washers often share similar designs across multiple model numbers, but parts can still differ by revision. Using the exact model number helps us match the right components, such as the washer inlet valve 285805 or washer drain pump WP3363394.

A one-digit mismatch can lead to ordering a part that looks right but will not mount, seal, or connect correctly, which can cause leaks, no-fill issues, or draining problems.

Last updated: February 2026

Yes, repairing a Kenmore washer is usually worth it when the fix restores reliable washing and spinning for significantly less than replacing the machine. For Kenmore model 11026902692, many common failures are repairable with standard parts and basic troubleshooting from the owner's manual.

We use a simple rule: repair when the total repair cost is less than about 50% of the cost of a comparable new washer and the tub and cabinet are in good shape.

Consider these factors:

• What failed: Wear items (pump, coupling, agitator dogs) are typically cost-effective.
• How the washer performed before the failure: If it cleaned well and spun well, repairs tend to pay off.
• Leak and rust severity: Chronic tub leaks or heavy rust usually push the decision toward replacement.
• Noise and vibration: Often fixable by leveling or suspension parts.
• Downtime: If you need a fast fix, in-stock parts can shorten turnaround.

These are frequent, high-value repairs for this style of Kenmore top-load washer:

These steps can prevent an unnecessary repair:

• Confirm the washer is level and the front leg nuts are tight; loose leveling hardware can cause vibration and poor spinning.
• Check the drain hose for kinks or clogs before replacing the pump.
• Reduce load size and redistribute bulky items if the washer bangs or walks.
• Verify water supply is on and hoses are not restricted if fill seems slow.

A targeted repair can restore performance for years, especially on a straightforward mechanical washer like the Kenmore 11026902692. Using the correct troubleshooting steps and matching the symptom to the right part helps you avoid replacing good components.

Last updated: February 2026

Most Kenmore washers average 10 to 15 years of service life in normal household use. Your Kenmore washer model 11026902692 is built for long-term operation; regular care, correct loading, and prompt repair of wear parts help you stay in that range (or longer). See the maintenance and operating guidance in the 11026902692 owner's manual.

A washer’s lifespan is mainly driven by how hard it works and how well it is maintained.

• Loads per week: more cycles equals faster wear on the drive system and pump
• Overloading: strains the clutch, coupling, and gear case
• Out-of-level installation: increases vibration and suspension wear
• Water quality and detergent use: excess suds and residue can shorten component life
• Small leaks left unfixed: can damage bearings, motor, and electrical parts

On a direct-drive Kenmore top-load washer like model 11026902692, these parts often determine whether the machine keeps washing well as it ages:

These steps match how this washer is designed to operate and help prevent avoidable breakdowns.

• Keep the washer level and stable on the floor
• Use the correct water level for the load size; avoid packing the basket
• Run occasional hot wash cycles (when safe for fabrics) to reduce buildup
• Check hoses and the pump area for drips and address them quickly
• If performance changes, stop repeated restarts and troubleshoot before more damage occurs

A washer near the end of its typical lifespan can still be a great value if the issue is a normal wear item (like a coupling or drain pump). Catching symptoms early helps you avoid secondary damage to higher-cost assemblies such as the gear case.

Last updated: February 2026

The cubic foot capacity for your Kenmore washer model 11026902692 is listed in the product specifications in the 11026902692 owner's manual. If you do not see a cubic-feet number, you can still confirm capacity by using the basket measurements method below.

In the manual, capacity is usually shown as basket/tub capacity or tub volume in the specifications or features area.

• Check the Specifications section first
• Look for wording like capacity, tub volume, or basket size
• If the manual uses a size label (for example, “super capacity”), treat it as a size class, not a cubic-feet number
• If only dimensions are provided, calculate cubic feet from the basket size

This gives a reliable estimate when cubic feet is not printed.

• Measure the inside diameter of the wash basket (inches)
• Measure the usable depth (inches) from the bottom to the normal fill line
• Convert inches to feet (divide each measurement by 12)
• Use: Volume = 3.1416 × (radius in feet)² × (depth in feet)

Knowing capacity helps you load correctly so the agitator can circulate clothes, the washer can balance during spin, and parts like the drive system and drain pump are not overworked.

Last updated: February 2026