Kenmore 11096582110 electric dryer Parts

Most Kenmore 11096582110 electric dryers are full-size, 27-inch class machines. A typical exterior footprint is about 27 inches wide, 27 to 29 inches deep, and 43 to 44 inches tall; use your space and vent location to confirm fit before moving or stacking.

Typical dimensions you can plan around

For a Kenmore 110-series, these are the common planning ranges:

• Width: ~27 inches
• Height: ~43 to 44 inches
• Depth (cabinet): ~27 to 29 inches
• Depth (with door/controls clearance): plan +2 to 4 inches
• Side clearance: at least 1 inch each side for airflow and vibration
• Rear clearance: at least 4 inches for the exhaust duct bend

How to measure your dryer correctly

Measure the dryer itself and the space it sits in.

• Measure width at the widest point of the cabinet.
• Measure height from floor to the top of the control panel.
• Measure depth from the back panel to the front edge; then add room for the door swing.
• Confirm the vent outlet location so the duct does not crush when pushed back.
• If you are moving through doorways, measure the narrowest doorway and compare.

Quick planning table

What you’re planning	What to use	What to add
Closet width	~27 in dryer width	+2 in minimum clearance
Closet depth	~27 to 29 in dryer depth	+4 in for vent, +2 to 4 in for door
Vertical space	~43 to 44 in height	+1 in for leveling and airflow

Why it matters

Correct sizing prevents crushed venting (long dry times), door clearance problems, and installation headaches. It also helps you avoid damaging parts like the dryer door seal W10906683 when sliding the dryer into a tight opening.

Last updated: February 2026

For Kenmore electric dryer model 11096582110, replacing the thermistor means disconnecting power, accessing the blower housing or heater circuit area, swapping the sensor, and restoring all wiring exactly as found. If your dryer is overheating, not heating, or stopping mid-cycle, the thermistor is a common check.

Before you start (safety and prep)

• Unplug the dryer; for an electric dryer, also switch off the breaker.
• Let the dryer cool completely if it was running.
• Use a phone photo to document wire locations before disconnecting anything.
• Have a nut driver/screwdriver ready; most access is through the rear panel.
• Clean lint from the cabinet while it is open; airflow problems can mimic sensor failures.

Replacement steps (typical Kenmore 110-style electric dryer)

1. Disconnect power.
2. Remove the rear panel to access internal components.
3. Locate the thermistor (commonly mounted on the blower housing or near the exhaust air path).
4. Disconnect the wire connector from the thermistor.
5. Remove the mounting screw(s) and take out the thermistor.
6. Install the new thermistor in the same position and orientation.
7. Reconnect the wiring, reinstall the rear panel, restore power, and test a timed dry cycle.

Quick diagnosis tips (so you do not replace the wrong part)

• If the dryer runs but heat is erratic, check airflow first (lint screen, vent, outside hood).
• If the dryer overheats, inspect the cycling thermostat and venting.
• If the dryer will not start, a thermistor is less likely; check the door switch and start switch.

Common symptoms and what they usually point to

Symptom	Most common cause	Parts often involved
Overheating or burning smell	Restricted venting	Blower wheel, thermostat
No heat but drum turns	Heater circuit fault	Thermal cut-off kit, thermostat
Will not start	Safety interlock/control issue	Door switch, push-to-start switch

Parts we often see involved on this model

If testing shows a related component is the real issue, these are common matches for model 11096582110:

• Dryer operating thermostat WP3387134
• Cut-off kit 279769
• Dryer blower wheel WP694089

Why it matters

The thermistor helps regulate temperature. When it is out of range or the dryer cannot move air, cycles can run too hot, shut down early, or dry poorly. Fixing the sensor and airflow together prevents repeat failures.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the appliance’s ID label; for Kenmore model 11096582110, you’ll typically find that label in the door opening (around the frame) or on the back panel. Once you have the full model number, we can match the correct parts and diagrams.

Where to look for the model number label

Check these common spots on Kenmore electric dryers:

• Inside the dryer door opening on the cabinet frame (most common)
• On the back panel of the dryer cabinet
• Along the door opening edge near the latch area
• On the inside of the front panel (visible after removing the lower access panel on some designs)
• Near the lint screen housing (less common)

What the model number looks like (and why it matters)

Kenmore model numbers are usually 10 to 11 digits. For this dryer, the full model number is 11096582110. The first three digits often indicate the manufacturing source (for example, many Kenmore dryers starting with 110 were built for Sears by Whirlpool).

Quick ID guide

What you have	Example	What it tells us
Full model number	11096582110	Exact parts fit and correct diagrams
Partial model prefix	110	Helps narrow the platform, but not enough for ordering
Serial number	Varies	Production run info; not a parts lookup replacement

Tips to avoid ordering the wrong part

Before you buy a belt, switch, or thermostat, confirm the model number exactly as printed (including any extra digits).

• Write it down exactly; do not add dashes or spaces
• Take a clear photo of the label for reference
• Match parts by model, not by “looks the same”
• If your dryer won’t start, confirm the model first, then check common start-related parts like the dryer push-to-start switch WP3395382 and the dryer door switch W10820036

Why it matters

Kenmore dryers can look nearly identical across different series, but internal parts like the drive belt, timer, and thermostats can vary by model. Using the exact model number (11096582110) prevents fit issues and repeat repairs.

Last updated: February 2026

Common problems on Kenmore electric dryers like model 11096582110 include no heat, long dry times, the drum not turning, and loud squealing or thumping. These issues usually trace back to airflow restrictions (lint and venting) or normal wear of drive and temperature-control parts.

Most common symptoms and what usually causes them

• Dryer runs but won’t heat: failed thermostat, heater circuit issue, or a safety cut-off opening
• Long drying times: clogged lint screen, restricted vent, or weak airflow from the blower
• Drum won’t turn: broken belt, worn idler pulley, or a failing drive motor
• Loud noise (squeal, rumble, thump): worn drum support parts, idler pulley wear, or belt wear
• Won’t start: door switch problem, start switch issue, or motor-related failure

Parts that commonly fix these problems (for model 11096582110)

If your symptom matches, these are frequently replaced parts for this model:

Symptom	Common part to check/replace	Example part for this model
Drum won’t turn	Belt and tension system	Drum belt 341241, dryer idler pulley WP691366
Loud squeal/rumble	Drum support and drive components	Dryer idler pulley WP691366, drive motor 279827
Long dry times	Airflow components	Dryer blower wheel WP694089
No heat or overheating	Temperature control and safety cut-off	Dryer operating thermostat WP3387134, cut-off kit 279769
Won’t start	Start or door interlock	Dryer push-to-start switch WP3395382, dryer door switch W10820036

Quick checks we recommend before replacing parts

• Clean the lint screen completely (wash off fabric softener residue if present)
• Inspect the vent hose for kinks, crushing, or heavy lint buildup
• Confirm strong airflow at the outside vent hood while the dryer runs
• Listen for motor hum with no drum movement (often belt or idler related)
• If heat is weak, stop using the dryer and check the heater safety circuit parts first

Why it matters

Airflow problems can cause long dry times and overheating, which stresses the heating circuit and can lead to repeated failures. Catching a worn belt, idler pulley, or restricted vent early helps prevent bigger repairs and keeps drying performance consistent.

Related help: Kenmore 110 series electronic control model dryer error codes

Last updated: February 2026