Kenmore Elite 79571054012 refrigerator Parts

For Kenmore Elite refrigerator model 79571054012, the correct replacement water filter is ADQ36006102 (often referenced as “9690”). You can confirm the exact filter and replacement steps in the 79571054012 owner's manual, then match the filter by part number to avoid fit and leak issues.

We recommend using these checks in order:

• Match your model number: use 79571054012 (usually found on the inside wall of the fresh food section).
• Check the manual’s filter section for the replacement filter number and reset steps.
• Match the filter part number: this model uses ADQ36006102.
• Compare to the part listing to ensure you are ordering the correct cartridge.
• Keep the bypass plug for times when a replacement filter is not available.

From our manual guidance for this model:

• Replace the filter about every 6 months, or sooner if dispenser flow drops.
• After installing a new filter, flush about 2.5 gallons (roughly 5 minutes) and check for leaks.
• Reset the filter indicator by pressing and holding Ultra Ice (Filter Reset) for at least 3 seconds.

Using the correct filter for Kenmore 79571054012 helps maintain water taste, protects the water system from leaks at the O-rings/manifold connection, and keeps ice and water dispenser flow from dropping prematurely.

Last updated: January 2026

Common problems on the Kenmore Elite refrigerator model 79571054012 include warm temperatures (often airflow or condenser-coil related), ice maker or dispenser issues, water leaks from a clogged drain, and vibration or rattling from leveling problems. Our 79571054012 owner's manual also notes normal run-time changes and provides a troubleshooting guide.

• Not cooling or weak cooling: clean condenser coils, confirm doors seal tightly, and verify the evaporator fan is running.
• Compressor seems to run too much: frequent door openings, warm room temperature, or adding lots of food can increase run time.
• Vibration or rattling noise: adjust leveling legs and make sure the refrigerator sits solidly on the floor.
• Ice maker not making ice: confirm the ice compartment door closes tightly and the ice bin is not overfilled or uneven.
• Water leaking or puddles: check for a blocked defrost drain and inspect the drain tube.

If troubleshooting points to a failed component, these model-matched parts are common fixes:

Catching these issues early helps protect food temperatures, reduces energy waste (long run times), and prevents water damage from slow leaks. Simple maintenance like cleaning condenser coils and keeping doors aligned often prevents bigger repairs.

• Use the troubleshooting section in the 79571054012 owner's manual to match symptoms to checks.
• For dispenser and ice-area access steps, follow how to disassemble a Kenmore refrigerator dispenser.
• If you see a display error, use Kenmore 795 model bottom freezer refrigerator error codes to narrow the failure to a sensor, fan, or defrost-related issue.

Last updated: January 2026

Water leaking from the bottom of your Kenmore Elite refrigerator model 79571054012 is usually caused by a clogged defrost drain that overflows into the cabinet, or a leak in the water supply system (tubing, fittings, or inlet valve) that drips down to the floor.

• Clogged defrost drain: Water from the defrost cycle should flow to the drain pan; if the drain is blocked, it can back up and leak out.
• Leaking water line connection: A loose compression nut or fitting can drip, especially after moving the refrigerator.
• Cracked or pinched dispenser tubing: Look for wet tubing or mineral tracks near the back and under the unit.
• Water inlet valve seepage: The valve can weep slowly and create a puddle over time.
• Ice maker fill leak: A small leak at the fill tube or connection can run down and appear as a bottom leak.

1. Unplug the refrigerator and pull it out far enough to inspect behind it.
2. Check the floor and rear lower area for the highest wet point (that is usually the source).
3. Inspect the water supply hookup: look for drips at the shutoff valve, compression nut, and the refrigerator connection.
4. Look for wet tubing along the back; if it is damaged, replace the line.
5. Check the drain pan area for overflow signs; if the pan is full repeatedly, focus on the defrost drain.

A small leak can turn into floor damage and can also cause ice maker and water dispenser problems if air gets into the water line. Fixing the source early helps protect the compressor area and keeps cooling performance stable.

• Use the water line connection steps and leak-check cautions in the 79571054012 owner's manual when inspecting fittings.
• For prevention tips that reduce repeat leaks, follow how to prevent water dispenser and ice maker problems.

Last updated: January 2026

Kenmore Elite refrigerator model 79571054012 is a bottom-mount (bottom freezer) refrigerator; the most accurate “size” details (overall dimensions and capacity) are listed in the specifications section of the 79571054012 owner's manual. For planning, measure your unit in place and compare to typical 33-inch-class dimensions.

• Overall width: measure at the widest point (door edges).
• Overall height: floor to top hinge cover; include leveling feet setting.
• Overall depth: measure without handles and including handles.
• Capacity (cu. ft.): listed in the specs; it is not the same as exterior size.
• Clearances: space needed for airflow and door swing.

Use these ranges to estimate fit before you pull the refrigerator out to measure.

Correct dimensions prevent installation issues like doors hitting cabinets, restricted ventilation (warm temperatures and longer run times), and difficulty removing drawers or bins.

If your model has an ice maker or water dispenser, confirm water line routing and clearance guidance in the 79571054012 owner's manual. If you are also replacing the filter during setup, match the correct filter to your model, such as the refrigerator water filter 9690 AGF80300801.

Last updated: January 2026