Kenmore 66513242K900 dishwasher Parts

Yes. We still support replacement parts for many Kenmore dishwashers, including model 66513242K900. The key is matching parts by the full model number so you get the correct fit for common repairs like draining issues, leaks, heating problems, and rack hardware.

Use the model number 66513242K900 and confirm the part name and ID before ordering. Your 66513242K900 owner's manual is also a good reference for maintenance and troubleshooting sections.

• Match by model number first (66513242K900)
• Identify the symptom (won’t drain, leaking, not cleaning, not heating)
• Compare the part name + part ID (not just a description)
• Replace related wear items at the same time when it makes sense (hose clamps, seals)
• Follow safe shutoff steps: power off at breaker, water supply off

These are examples of frequently replaced parts for this model family:

Kenmore dishwashers are built in multiple design families, and parts can look similar but mount differently. Matching by 66513242K900 helps avoid wrong-fit issues with items like the sump and motor assembly, wire harnesses, and seals.

If you’re seeing a flashing pattern or an error, use Kenmore 665 model dishwasher error codes to narrow the failure to a specific system (drain, fill, heating, or control).

Last updated: February 2026

To force-drain your Kenmore dishwasher model 66513242K900, press CANCEL/DRAIN with the door fully closed. The dishwasher runs a 2-minute drain (if needed) and then the Cancel/Drain light turns off when draining is complete. See the 66513242K900 owner's manual.

• Close the dishwasher door completely (it will not drain with the door open).
• Press CANCEL/DRAIN once.
• Wait about 2 minutes for the drain sequence to finish.
• If you need to stop draining early, press CANCEL/DRAIN again.
• Before starting a new wash cycle, make sure the tub is drained.

A forced drain command helps only if the dishwasher can physically move water out. Check these common causes:

• Garbage disposal knockout plug still in place (new disposal installs are a frequent cause).
• Drain hose kinked, crushed, or routed incorrectly (it should avoid rubbing the motor and sharp cabinet edges).
• Air gap or sink drain connection clogged.
• Standing water and debris in the sump area (food soil can block flow).
• Drain pump not running or humming; the dishwasher drain pump WPW10348269 is the component that pushes water out.

Cancel/Drain clears the current cycle and runs a timed drain so you can safely restart with fresh settings. This prevents reusing dirty water and helps avoid poor cleaning results and odors.

Last updated: February 2026

For Kenmore dishwasher model 66513242K900, the most reliable “hard reset” is a full power cycle: turn the dishwasher off at the breaker (or unplug it) for about 5 minutes, then restore power and start a cycle. To clear a stuck cycle or indicators, use CANCEL/DRAIN and let the 2-minute drain finish (door closed). See the 66513242K900 owner's manual for the exact control behavior on your panel.

• Hard reset (power cycle): breaker OFF (or unplug) for ~5 minutes, then ON.
• Cancel and drain: press CANCEL/DRAIN; let the dishwasher run the 2-minute drain.
• Clear selections before starting: press CANCEL/DRAIN to clear options and cycles, then choose a new cycle.
• If controls seem unresponsive: check whether Lock On is enabled.

This model uses the HEATED DRY button to toggle the control lock.

• To turn Lock On on: press and hold HEATED DRY for 3 seconds.
• To turn Lock On off: press and hold HEATED DRY for 3 seconds.
• If you open the door while locked, you must unlock and press START/RESUME to continue.

A power cycle clears temporary control glitches, while CANCEL/DRAIN safely stops the current cycle and drains water so you can restart cleanly. Unlocking Lock On prevents unnecessary part replacement when the dishwasher is actually working normally.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66513242K900 is usually worth it when the problem is a wear item or a single failed part and the tub and racks are still in good shape. It becomes less worthwhile when multiple major components are failing or the repair cost approaches the price of a replacement.

• Age: Under ~10 years old, repairs are typically a good value; over ~10 years, be more selective.
• Repair cost vs. replacement: If the repair is under ~50% of replacement cost, repair usually makes sense.
• Type of failure: Pumps, leaks, and draining issues are often straightforward; repeated electrical issues can add up.
• Condition: Rusted racks, cracked tub, or chronic leaks usually push toward replacement.
• DIY ability: If you can safely do basic checks, you can save a lot on labor.

Many “won’t drain” or “poor wash” complaints come down to a few serviceable parts:

A targeted repair can restore cleaning and draining performance for far less than replacing the entire dishwasher. Also, proper installation clearances help prevent repeat failures; the installation instructions call out keeping drain, water, and wiring from contacting the motor or legs, and ensuring the motor does not touch the floor (no carpet installs). See the installation guide.

• Confirm the dishwasher is getting power and the door latches fully.
• Check for a clogged sink/disposer connection and a blocked drain path.
• Clean the drain air gap (if your setup has one) and verify good flow.
• Look for leaks at the door and tub perimeter; a worn seal can mimic bigger problems.
• Review troubleshooting and care steps in the owner's manual.

Last updated: February 2026

Common problems on Kenmore dishwashers like model 66513242K900 are poor cleaning, not draining, leaks, and “won’t start” or stopping mid-cycle. In most cases, the fix is basic maintenance (filters, spray arms, loading) or replacing a failed part such as a drain pump, inlet valve, or door seal; see the 66513242K900 owner's manual for model-specific checks.

• Dirty dishes or film: clogged filter, blocked spray arms, low water temperature, overloading, or low rinse aid
• Water left in the tub: kinked/clogged drain hose, blocked air gap, failed drain pump
• Leaking at the door: worn door seal, door not latching, tub overfill/float issue
• Won’t start or stops: door not latched, power interruption, tripped breaker or blown house fuse, motor overload reset
• Poor drying: rinse aid empty, air-dry setting used, heater circuit issue

1. Confirm the door is fully closed and latched (a common reason it won’t run).
2. Verify power: breaker on, house fuse good (the manual notes checking for a blown household fuse or tripped breaker).
3. Make sure the water shutoff valve is on.
4. Clean the filter area and check spray arms for debris.
5. If you see spots or cloudy film, adjust detergent and use rinse aid; the manual notes some film/etching can be permanent.

Catching the symptom early prevents repeat wash cycles, standing water odors, and moisture damage. A simple clog or a worn seal can look like a major failure, so the quick checks above often save time and parts.

For installation-related issues (drain routing, clamps, clearances), follow the installation guide.

Last updated: February 2026

Your Kenmore dishwasher’s model number is printed on the model and serial number label inside the door area. On Kenmore dishwashers like model 66513242K900, that label is typically on the inner door frame or along the tub opening where you can see it when the door is open (see the 66513242K900 owner's manual).

• Open the door and look along the inner door frame (left or right side)
• Check the top edge of the door and the tub lip/opening
• Look on the tub wall near the front opening
• If the label is worn, use a flashlight and look for etched or faint printing

• Check the side of the door (visible when the door is partially open)
• Look behind the toe-kick/lower access panel area for additional stickers
• If the dishwasher was recently installed, confirm the model from your paperwork and compare it to the label location guidance in the 66513242K900 installation guide

We use the model number to match the correct Kenmore dishwasher parts and troubleshooting steps. Even small differences in a 665-series dishwasher can change which drain pump, heater element, or door seal fits.

• Model number (example: 66513242K900)
• Serial number
• Electrical ratings (volts/amps)

Last updated: February 2026

Kenmore dishwasher model 66513242K900 was manufactured by Whirlpool. On Kenmore appliances, the “665” prefix is the manufacturer code commonly used for Whirlpool-built Kenmore dishwashers, so parts and service information typically align with Whirlpool-built designs.

We recommend verifying the model and prefix directly from the rating label so you match the right parts (like a drain pump, water inlet valve, or heater element).

• Find the model/serial label (often on the tub frame near the door).
• Confirm the full model number is 66513242K900.
• Check that the first three digits are 665.
• Use the model number when ordering parts or looking up diagrams.
• Keep the documentation handy for feature and cycle details in the 66513242K900 owner's manual.

Kenmore is a brand name; different manufacturers built different Kenmore models. The manufacturer code helps ensure you get compatible components such as the circulation system, controls, and door hardware.

If you are troubleshooting common issues (not draining, not heating, poor cleaning), these model-matched parts are often involved:

• Dishwasher drain pump WPW10348269 (drain problems)
• Dishwasher water inlet valve W10648041 (filling problems)
• Heater element WPW10082892 (drying or heating problems)
• Dishwasher sump and motor assembly WPW10780877 (wash performance and circulation)

Knowing Whirlpool built 66513242K900 helps you use the correct repair guidance and order the right Kenmore-compatible parts the first time, especially for core systems like the sump, motor, and drain path.

Last updated: February 2026