Samsung DVE60M9900V/A3-00 dryer Parts

On the Samsung DVE60M9900V dryer, we clear many temporary error (information) codes by power-cycling the dryer (turn it off, then remove power briefly). If the same code comes back, the dryer is detecting a real condition (like airflow restriction, door issue, or a sensor problem) that needs troubleshooting, not repeated resets.

Quick reset steps (power cycle)

• Press POWER to turn the dryer off.
• Unplug the dryer for 1 to 5 minutes (or switch the dryer breaker OFF for 1 to 5 minutes).
• Restore power.
• Start a simple cycle (for example, TIME DRY) and see if the code returns.
• If the code returns immediately, stop the cycle and troubleshoot the cause.

Use the code to guide what to check first

Your DVE60M9900V manual lists common information codes and the first checks to perform. See the DVE60M9900V user manual.

Here are high-value checks that fix many repeat codes:

• Clean the lint filter and make sure it is seated correctly.
• Check the venting for kinks, crushed duct, or a blocked outside hood.
• Confirm the door closes firmly and no laundry is caught in the door opening.
• Avoid overloading; heavy loads can trigger moisture and temperature related codes.
• Verify power supply is stable (especially after storms or breaker trips).

Common codes and what they usually mean on this model

Code (display)	What it points to	Best first action
DC	Door open or door not sensed closed	Re-close door; check for items caught in door
HC	High temperature heating check	Clean lint filter; check vent restriction
tC / tC5	Thermistor (temperature sensor) reading out of range	Clean lint filter; check vent restriction
9C1	Power supply needs to be checked	Verify outlet/breaker; avoid extension cords

Why it matters

Clearing the code gets the control board out of “alarm” mode, but the dryer will keep protecting itself if it still senses overheating, restricted airflow, or a sensor/door problem. Fixing the root cause helps prevent long dry times, no-heat symptoms, and repeat shutdowns.

Helpful related guidance

• For a broader list of Samsung dryer codes and fixes, use our Samsung dryer error codes resource.
• If your dryer uses Smart Care diagnostics, our Samsung smart care dryer error codes guide can help you interpret app-based results.

Last updated: January 2026

No. A Samsung DVE60M9900V electric dryer is designed for a 120/240V (or sometimes 120/208V) supply; plugging it into 110V or 120V will not provide enough power for the heater and can cause unsafe wiring overheating or nuisance breaker trips. Use the correct dedicated dryer circuit.

What to do instead (safe options)

• Install a dedicated 30-amp dryer circuit with the correct receptacle for your cord type (3-prong or 4-prong).
• If your home has only 120V laundry power available, choose a 120V dryer or a gas dryer (if gas service and venting are available).
• If you are moving into a new place, confirm the laundry outlet type before delivery.
• If you are unsure whether your unit is configured as gas or electric, check the data label and the electrical requirements section in the DVE60M9900V user manual.
• Avoid “adapter” solutions; they do not create the required 240V supply and can create a fire hazard.

Why 110V will not work for a 220V/240V dryer

Most of the energy an electric dryer uses is for the heating element. On 120V, the dryer cannot deliver the wattage needed to heat properly, so you typically get:

• No heat or very weak heat
• Extremely long dry times
• Higher current draw on an undersized circuit (overheating risk)
• Potential damage to wiring, cord, terminal block, or control components

Quick comparison

Power available at outlet	Typical result with a 240V electric dryer	Recommended action
120V (standard household)	Drum may run; heat will not dry correctly	Install proper 240V circuit
120/240V or 120/208V	Normal operation when correctly wired	Use correct cord and receptacle

Why it matters

Correct voltage and a dedicated circuit protect the dryer’s heater circuit, motor, and controls, and they reduce the risk of overheating at the outlet, cord, and terminal connections.

Last updated: January 2026

On the Samsung DVE60M9900V dryer, “E3” is not one of the documented information codes in the model’s manual, so we can’t map it to a single, model-specific failure from the official code table. In practice, treat it as a display-variation code and start with airflow, load, and reset checks.

Confirm what code the dryer is actually showing

Samsung displays can look similar (for example, “E3” vs “3E”, “tC”, “HC”, or “9C1”). Before replacing parts, we recommend verifying the exact characters on the display and whether the code appears on the Delicate Dryer or the Tumble Dryer.

• Write down the code exactly as shown (letters, numbers, and any “1” prefix).
• Note which section is running (Delicate Dryer top compartment vs Tumble Dryer drum).
• Power the dryer off, then back on, and see if the same code returns.
• Check for a second code after restarting a cycle.

Fast checks that fix many code situations

These steps are safe and align with the DVE60M9900V troubleshooting and maintenance guidance in the DVE60M9900V user manual.

• Clean the lint filter before restarting.
• Reduce the load size; run a small load to confirm normal tumbling.
• Check the exhaust hood outside; it should open freely.
• Inspect the vent for kinks, crushing, or heavy lint buildup.
• Reset power: unplug (or switch off the breaker) for 5 minutes.

Use the built-in Vent Blockage Test (model-specific)

This model includes a Vent Blockage Test that reports “0” for normal venting or “CLg” for restricted venting.

Test result	What it indicates	What to do next
0	Venting looks normal	Recheck load size and watch for repeat codes
CLg	Vent restriction detected	Clean/shorten/straighten ducting and retest
Another code	A specific fault is being reported	Look up that exact code in the manual

Why it matters

Many Samsung dryer codes are triggered by restricted airflow or abnormal operating conditions; fixing venting and load issues can prevent overheating, long dry times, and repeat shutdowns.

For broader code naming variations across Samsung dryers, we also use our Samsung dryer error codes reference.

Last updated: January 2026