Kenmore 11064642400 dryer Parts

For Kenmore dryer model 11064642400, the exact drum capacity (cubic feet) is not listed in the provided manual excerpts; most full-size 27-inch Kenmore/Whirlpool-built dryers of this style are typically about 6.0 to 7.0 cu. ft. Confirm the exact capacity using the 11064642400 owner's manual.

How to confirm the exact capacity for model 11064642400

We recommend using the model-specific documentation first, then verifying by physical measurements if needed.

• Check the specifications section in the 11064642400 owner's manual.
• Look for a “capacity” or “drum volume” line in the features/specs pages.
• If you have the original sales receipt or product listing, compare the listed capacity to your model number.
• If you measure the drum, measure inside diameter and inside depth (in inches) and calculate volume.
• Use capacity as a guide for load size; overloading reduces airflow and drying performance.

Quick capacity reference (typical ranges)

These ranges help you sanity-check what you find in the manual.

Dryer type (common)	Typical capacity range	What you’ll notice
Compact (24-inch)	3.4 to 4.4 cu. ft.	Smaller door opening, shorter drum
Full-size (27-inch)	6.0 to 7.0 cu. ft.	Standard household size
Oversize	7.2+ cu. ft.	Extra-deep drum, larger loads

Why it matters

Capacity affects how much laundry you can dry per load and how well air circulates through the drum. If loads are too large for the drum size, drying times increase and heat-related parts can run hotter than intended.

Last updated: January 2026

Most Kenmore dryers, including model 11064642400, typically last 10 to 13 years with normal household use. Regular lint and vent cleaning, avoiding overloads, and fixing small issues early can help a dryer reach the upper end of that range.

What affects dryer lifespan the most

• Airflow and venting: Restricted airflow makes the dryer run hotter and longer.
• Lint buildup: Lint in the cabinet or exhaust increases heat stress on parts.
• Load size and frequency: Heavy, frequent loads wear the belt, rollers, and motor faster.
• Heat system health: Weak heating or overheating strains thermostats and fuses.
• Basic care habits: Cleaning the lint screen every load is one of the biggest life extenders.

Maintenance schedule we recommend for 11064642400

The Kenmore manual calls out routine lint-screen cleaning every load and deeper lint removal on a longer interval. See the 11064642400 owner's manual for the exact care instructions.

Task	How often	Why it helps
Clean lint screen	Every load	Improves airflow and drying time
Clean exhaust venting	About every 2 years (or more with heavy use)	Reduces overheating and long run times
Cabinet lint cleaning (qualified service)	About every 2 years	Protects motor and heating components
Check door seal and latch feel	Monthly	Prevents heat loss and poor drying

Parts that commonly wear as a dryer ages

If your dryer still runs but is noisy, slow to dry, or the drum slips, these are common wear items:

• Drum drive system (belt, idler, support components)
• Blower wheel and airflow path
• Heating system components (element, thermostats, thermal cut-off)

For example, a worn belt can cause slipping or a drum that will not turn; the correct replacement for this model is the dryer drum belt 341241.

Why it matters

A dryer that is struggling to move air often takes longer to dry and runs hotter; that shortens the life of key components like the heating element, thermostats, and motor.

Last updated: January 2026

To hard reset Kenmore dryer model 11064642400, we recommend disconnecting power for about 5 minutes, then restoring power and starting a new cycle. This clears many temporary control or motor-protector conditions; if the dryer still will not run, focus on power supply, door closure, and airflow maintenance.

Hard reset steps (safe and effective)

• Turn the cycle selector to OFF.
• Unplug the dryer (or switch both dryer breakers OFF).
• Wait 5 minutes.
• Restore power.
• Close the door firmly.
• Select a cycle and press PUSH TO START (restart steps are outlined in the 11064642400 owner's manual).

If the reset does not work, check these first

The manual’s troubleshooting points to a few common “no start” causes that a reset will not fix.

• Confirm the power cord is plugged in securely.
• Check for a tripped breaker or blown fuse; many dryers use 2 fuses or 2 breakers, and both must be on.
• Make sure the door is fully closed; a failed door switch can prevent starting.
• Clean the lint screen before or after each load and keep the exhaust area clear.
• If the dryer runs but shuts off or overheats, clean lint buildup in the exhaust venting.

Quick symptom-to-likely-cause guide

What you notice	What it usually points to	What to do next
No lights, no response	Power supply issue	Check both breakers/fuses, outlet, cord
Runs only with door held	Door switch issue	Inspect/replace dryer door switch WP3406107
Starts then stops, burning smell, very hot cabinet	Restricted venting or overheating protection	Clean venting and lint buildup; re-test
Drum will not turn but motor hums	Belt or drum support issue	Inspect belt and idler; consider dryer drum belt 341241 or dryer repair kit 4392065

Why it matters

A hard reset clears temporary conditions, but most repeat “won’t start” or “overheats” problems come from power supply issues, a door switch failure, or restricted airflow. Fixing the root cause prevents repeat shutdowns and helps drying performance.

Last updated: January 2026

Common problems we see on Kenmore dryer model 11064642400 are no heat, the drum not turning, long dry times, and loud or unusual noises. Most of these issues trace back to airflow restrictions (lint buildup or venting problems), a failed safety thermostat or fuse, or a worn drive system.

Most common symptoms and what usually causes them

• Dryer runs but no heat: tripped breaker (electric dryers use 2), blown fuse, failed heating circuit parts
• Dryer will not start: door not fully closed, start switch issue, door switch issue, power supply problem
• Takes too long to dry: clogged lint screen, crushed or restricted vent, blocked exhaust hood
• Loud squealing or thumping: worn idler pulley, belt wear, drum support wear (often addressed as a kit)
• Burning smell or overheating: restricted airflow, lint buildup inside cabinet or venting

Quick checks we recommend first (fast, no parts)

1. Clean the lint screen before every load and remove any residue buildup periodically.
2. Confirm strong airflow at the outside exhaust hood while the dryer runs.
3. For electric models, check that both breakers/fuses are on (the drum can turn with only one leg of power).
4. Verify you are not using an “air/no heat” cycle when you expect heat.
5. Inspect venting; use 4-inch heavy metal venting and avoid plastic or foil vent.

Parts that commonly fix these problems on 11064642400

Symptom	Common part to check/replace	Example part for this model
Drum won’t turn	Drum belt, idler pulley	Dryer drum belt 341241
No heat (electric)	Heating element, thermal cut-off kit	Dryer element 279838, dryer thermal cut-off fuse kit 279816
Won’t start	Door switch, push-to-start switch	Dryer door switch WP3406107, dryer push-to-start switch WP3977456
Loud noise	Wear items (rollers/idler/belt)	Dryer repair kit 4392065

Why it matters

Airflow problems do more than slow drying; they can overheat the dryer and repeatedly blow thermal safety parts. Keeping the lint screen and venting clear is the best way to prevent “no heat” and “long dry time” complaints.

For model-specific operating, care, and troubleshooting steps, follow the 11064642400 owner's manual.

Last updated: January 2026