Kenmore Elite 66513763K600 dishwasher Parts

On Kenmore Elite dishwasher model 66513763K600, the lower spray arm typically lifts off or unthreads from the hub after you pull out the lower rack. The key is to keep the arm and hub aligned so you do not crack the plastic or drop anything into the sump.

Quick steps to remove the lower spray arm

• Turn off power at the breaker (recommended before reaching into the tub).
• Pull the lower dishrack all the way out and lift it off the rails.
• Grasp the lower spray arm near the center hub.
• Remove the center retainer (some versions lift off; others unthread counterclockwise).
• Lift the spray arm straight up and out.
• Check that nothing fell into the pump area before reassembling.

Important tips (to avoid damage)

The spray arm must spin freely for good cleaning. If it feels stuck, do not pry hard.

• Wiggle the arm gently while lifting to free mineral buildup.
• Keep the center hub level; twisting the arm can crack the hub.
• If you remove screws nearby during other work, protect the pump area; the installation instructions recommend placing a towel over the pump assembly and spray arm area to prevent dropped hardware from falling into the sump.

What to check while it is off

What to inspect	What you are looking for	What it affects
Spray holes and channels	Food debris, hard water scale	Poor wash, arm not spinning
Hub/retainer fit	Stripped tabs, worn retainer	Arm pops off, leaks, noise
Clearance	Items that block rotation	Dishes not getting clean

Why it matters

If the lower spray arm cannot rotate freely, wash performance drops fast. Our use and care guidance for this model emphasizes loading so nothing interferes with spray arm rotation, which is one of the most common causes of “not cleaning” complaints.

For model-specific diagrams and any retainer style notes, use the 66513763K600 owner’s manual.

Last updated: February 2026

Yes, it’s often worth repairing a Kenmore Elite dishwasher like model 66513763K600 when the problem is a single failed part (pump, valve, control, rack hardware) and the tub is in good shape; targeted repairs typically cost less than replacement and avoid a full reinstall.

Quick decision checklist

• The dishwasher is cleaning well overall and the issue is new (draining, filling, starting, leaking).
• The tub and inner door panel are not leaking.
• The failure points to a common replaceable part (pump, inlet valve, fuse, control board).
• You have had few repairs in the last 12 months.
• You can do a DIY repair safely or labor costs are reasonable.

What your 66513763K600 warranty details suggest

Your Kenmore Elite documentation includes coverage that can make repair a better value early in ownership:

Item covered (from warranty)	Coverage length	What it means for “worth it”
Full appliance defects	1 year	Repairs may be low out-of-pocket during the first year.
Electronic control and power supply board	2 years (parts)	Control-related failures can be more cost-effective to fix.
Ultra Wash wash system (motor, pump, spray arms, seals, gaskets)	2 years (parts)	Wash and pump issues are often repairable.
Upper and lower racks (rust)	5 years (parts)	Rack problems can be worth fixing instead of replacing the unit.

For exact coverage terms and maintenance guidance, check the 66513763K600 owner’s manual.

Common repairs that are usually worth it

These are frequent, straightforward fixes on many Kenmore 665-series dishwashers:

• Not draining: check the dishwasher drain pump WPW10348269 and drain path.
• Not filling or filling slowly: check the dishwasher water inlet valve WPW10158389.
• Dead or intermittent power: check the fuse W10258275.
• Won’t start or acts erratic: control issues may involve the dishwasher electronic control board WPW10084141.

Why it matters

A repair-first approach can preserve your cabinet fit and plumbing setup, reduce downtime, and keep a stainless tub dishwasher running for years when the failure is isolated to a serviceable component.

Last updated: February 2026

Yes. The Kenmore Elite dishwasher model 66513763K600 uses a removable filter assembly that you can take out and rinse to help prevent poor draining, odors, and gritty residue on dishes. For the exact filter location and removal method, follow the steps in the 66513763K600 owner's manual.

How to remove and clean the filter

• Turn off the dishwasher and let it cool.
• Remove the lower rack for access.
• Unlock the upper filter assembly by turning it about a quarter turn counterclockwise.
• Lift out the upper filter, then lift and pull the lower filter forward to remove it.
• Rinse both filters under running water; use a soft brush for stuck-on soil.
• Reinstall the lower filter first, then lock the upper filter back in place.

What you should notice after cleaning

Before cleaning	After cleaning
Standing water or slow drain	Faster, more complete draining
Grit or debris left on dishes	Cleaner rinse and fewer particles
Musty odor	Fresher interior between cycles

When a “filter problem” is really a drain problem

If the filter is clean but the dishwasher still will not drain well, the issue is usually in the drain path.

Check these common causes:

• Clogged sink/disposer connection or drain line
• Blocked drain air gap (if your setup uses one)
• Kinked or restricted drain hose
• Weak or jammed drain pump

If you find the pump is not pushing water out, the dishwasher drain pump WPW10348269 is a common fix for no-drain symptoms on this model.

Why it matters

A clean filter keeps wash water moving correctly through the wash system, which improves cleaning performance and helps protect components like the circulation pump and drain pump from debris.

Last updated: February 2026

Common problems we see with Kenmore dishwashers (including model 66513763K600) are no-start or stopping mid-cycle, not draining, not filling, poor cleaning, and leaks. Many issues trace back to power/door-latch checks, water supply being off, or a failing pump, valve, or control.

Quick checks first (most common, lowest effort)

• Make sure the door is fully closed and latched; a loose latch can stop the cycle.
• Check the house breaker or fuse; reset/replace if needed.
• Confirm the cycle was selected correctly and the unit was started properly.
• Verify the water shutoff valve is turned on.
• If the motor overloaded, wait a few minutes; it can reset on its own.

For the model-specific operating and troubleshooting steps, follow the 66513763K600 owner's manual.

Common symptoms and the parts most often involved

Symptom	What it usually points to	Example model-matched part
Won’t start or stops	Door not latched, power issue, control problem	Dishwasher electronic control board WPW10084141
Won’t drain	Drain restriction, drain pump issue, drain hose issue	Dishwasher drain pump WPW10348269, dishwasher drain hose 8269144A
Won’t fill or fills slowly	Water supply off, inlet valve problem	Dishwasher water inlet valve WPW10158389
Poor wash performance	Circulation/sump issue, sensor issue	Pump motor WPW10780877, sensor WPW10705575

Why it matters

Catching the “simple” causes (door latch, breaker, water supply) prevents unnecessary part replacement. When a dishwasher runs but won’t fill or drain, the cycle can stall, leave standing water, and lead to repeat failures.

Installation-related issues that look like “a bad dishwasher”

If the problem started right after installation or moving the unit, we use the same checklist the installer guide recommends:

• Run the shortest cycle and check for water in the tub after about 2 minutes.
• Recheck that no installation steps were skipped.
• If it does not operate, recheck power, door latch, cycle selection, and water supply.

Those steps are outlined in the 66513763K600 installation guide.

Last updated: February 2026

On Kenmore Elite dishwasher model 66513763K600, the model number is printed on the model and serial number label located on the dishwasher itself. You will typically find this label on the inside edge of the door opening when you open the door; it lists both the model number and serial number.

Where to look on the dishwasher

Check these common label locations first:

• Inside the door opening along the left side of the tub frame
• Inside the door opening along the right side of the tub frame
• Along the top edge of the door (visible when the door is open)
• On the inner door panel near the latch area

For diagrams that show the label location and other key components, use the 66513763K600 owner’s manual.

What information to write down

Record these details exactly as shown on the label:

• Model number (example format: 66513763K600)
• Serial number
• Purchase date (if available)
• Any type/engineering code listed near the model number

Why it matters

We use the model number to match the correct Kenmore dishwasher parts and fit-tested replacements. Even small model-number differences can change which items fit, such as a control board, water inlet valve, or rack components.

Quick reference: model vs. serial

Item	What it tells us	Used for
Model number	Exact design and parts list	Ordering correct parts and manuals
Serial number	Production run details	Service history and some part variations

Last updated: February 2026

Kenmore Elite dishwasher model 66513763K600 is a Kenmore-branded unit built by Whirlpool. The key clue is the 665 model prefix, which identifies the original manufacturer for many Kenmore dishwashers in this series.

How we identify the manufacturer

Kenmore is a brand name; different companies build Kenmore appliances. For dishwashers, the model prefix is the fastest way to identify who made it.

• 665 prefix: Whirlpool-built dishwasher platform
• Kenmore nameplate: branding and warranty support, not the factory
• Series overlap: the manual covers multiple 665.1375#, 665.1376#, 665.1385#, and 665.1386# variants (color number changes)

For model-specific details like cycle behavior, control panel layout, and features (such as the ULTRA WASH soil removal system), use the 66513763K600 owner's manual.

Why this matters for parts and repairs

Knowing Whirlpool built your Kenmore 665-prefix dishwasher helps when you are:

• Matching replacement parts by design family
• Comparing symptoms to common Whirlpool-built dishwasher issues
• Using repair videos and guides that reference Kenmore 665 series and Whirlpool platforms

If you are troubleshooting a fault or blinking lights, the Kenmore 665 model dishwasher error codes guide is the quickest way to translate what the control is reporting.

Quick reference table

What you see	What it means	What to do next
Model starts with 665	Whirlpool-built Kenmore dishwasher	Use model-based parts lookup and the manual
Kenmore Elite branding	Kenmore product line and warranty	Follow Kenmore operating and care instructions
Error code or flashing lights	Control detected a problem	Check the error code guide and test likely parts

Related parts you might see during troubleshooting

Manufacturer identity often comes up when diagnosing common dishwasher problems (no drain, no fill, no start). These are examples of parts used on this model family:

• Drain issues: dishwasher drain pump WPW10348269, drain hose routing and air gap/high loop
• No fill/slow fill: water supply, inlet screen, dishwasher water inlet valve WPW10158389
• Dead/no power: house power, door latch checks, fuse W10258275

Why it matters

Using the correct manufacturer platform prevents ordering the wrong part and helps you follow the right diagnostic steps for the wash system, sensor logic, and control behavior.

Last updated: February 2026