Kenmore 11028133411 washer Parts

For Kenmore washer model 11028133411, the most reliable “hard reset” is a power reset: unplug the washer (or switch off the breaker) for 1 to 2 minutes, then restore power. If you’re clearing an error code, use the control’s START/PAUSE/Unlock Lid button steps shown in the owner's manual.

• Power reset: Unplug for 1 to 2 minutes; plug back in.
• Control reset after a pause: Close the lid, then touch and hold START/PAUSE/Unlock Lid for up to 3 seconds to restart.
• Clear an F-type error code: Touch START/PAUSE/Unlock Lid once to clear the code; then touch it again to restart.
• If the washer will not start: Confirm the lid is fully closed and the outlet has power (no extension cord).

Many Kenmore top-load washers do not have a single master reset button. Instead, the control lets you clear certain faults and restart.

• Make sure the lid is closed; the washer will not run with the lid open.
• Wait through normal pauses; this model can pause during phases of the cycle.
• Reduce oversudsing; too much (or non-HE) detergent can cause the washer to stop to manage suds.
• If you opened the lid to add items, restart correctly: press START/PAUSE/Unlock Lid to pause, wait for the lid to unlock, then close the lid and touch and hold START/PAUSE/Unlock Lid up to 3 seconds.
• If the lid will not lock or unlock consistently, a failed lid lock can mimic a control problem; check the washer lid lock assembly W10810403.

A true power reset clears temporary control glitches, while the START/PAUSE/Unlock Lid steps clear many display codes and safely restart the cycle. Using the correct method prevents unnecessary part replacement and helps protect the control from repeated interruptions.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years under normal household use. For your Kenmore 11028133411 top-loading high efficiency washer, consistent maintenance and avoiding overloads are the biggest factors that keep the drive system, suspension, and water-handling parts running longer (see the owner's manual).

Most washers reach the end of their service life because of wear in moving parts, water leaks, or control issues, not because the cabinet “wears out.”

Common factors that extend lifespan:

• Use HE detergent only and measure it correctly to reduce residue and stress on the drain system
• Load items in loose heaps evenly around the washplate to reduce out-of-balance wear
• Keep the washer level and stable to protect the suspension and tub components
• Run periodic cleaning/maintenance routines to reduce odor and buildup
• Address small issues early (slow drain, noisy spin, lid not locking) before they cascade

When a washer is aging, a few assemblies tend to be the “make-or-break” repairs because they affect spin, agitation, draining, and safety interlocks.

Knowing the 10 to 15 year average helps you decide whether to invest in a larger repair (drive, tub, basket) versus a targeted fix (lid lock, inlet valve, drain pump). It also helps you plan maintenance that reduces vibration, leaks, and strain on the motor and suspension.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the problem is a common wear item and the machine is otherwise in good shape. For Kenmore model 11028133411, repairs like a lid lock, drain pump, or water inlet valve typically restore reliable operation for far less than replacing the washer.

We use these practical rules to decide repair vs. replace:

• The washer completes cycles and does not leak heavily from the tub area
• The issue is isolated (no multiple symptoms across fill, drain, and spin)
• The repair is a single-part fix (valve, pump, lid lock, clutch-related parts)
• The cabinet and outer tub are not rusted through
• The repair cost is clearly less than about half the cost of a comparable new washer

These are frequent, straightforward fixes that often solve “won’t start,” “won’t drain,” or “won’t fill” complaints:

• Lid will not lock or washer will not start: washer lid lock assembly W10810403
• Washer will not drain or leaves water in tub: washer drain pump W10876600
• Washer will not fill or fills slowly: washer water inlet valve W11165546
• Agitation/spin performance issues (clutch system wear): slider W10734521 and clutch coil W10754448

Replacement is the better value when the washer has major structural or high-cost failures:

• Outer tub or basket damage, severe bearing noise, or repeated leaks
• Multiple major components failing at once (drive system plus controls)
• You need a major assembly replacement and the washer has other age-related issues

A targeted repair keeps a dependable Kenmore high-efficiency, low-water top-load washer running and avoids the downtime and installation work of replacement. Your use and care steps (HE detergent, proper loading) also reduce repeat failures; see the owner's manual for model-specific guidance.

Last updated: February 2026

Kenmore model 11028133411 is a top-loading high-efficiency, low-water washer; its exact tub capacity in cubic feet is listed in the product specifications section of the owner's manual. For most Kenmore 110-series HE top-load washers in this design family, capacity typically falls in the 3.5 to 4.8 cu. ft. range.

We recommend checking the specification details in the owner's manual for your exact model. Look for sections labeled “Specifications,” “Capacity,” “Washer dimensions,” or similar.

• Confirm the model format matches 110.2813*410 (your manual family listing)
• Check for a “cu. ft.” value in the specs table
• If the manual lists multiple variants, match by color code (the “*” in the model family)
• Use the capacity to choose proper load size and cycle options

Capacity affects how much laundry you can wash per load and how well the washer can circulate items for cleaning and rinsing in a low-water HE design.

• Too large a load can cause poor cleaning, out-of-balance spinning, and longer cycle times
• Too small a load can reduce efficiency and may not distribute well for spin
• Correct capacity helps you choose the right cycle, soil level, and HE detergent amount

If you need a practical estimate while you confirm the exact spec in the manual, use this range:

If the washer struggles with large loads (slipping, weak agitation, or poor spin), a worn drive or clutch system can make the washer feel “smaller” than it is.

• Drive assembly W11393685 (spin and agitation drive components)
• Slider W10734521 (clutch-related wear item in the drive system)
• Damper assembly W11130356 (helps control tub movement during spin)

Last updated: February 2026