Kenmore Elite 11047798800 washer Parts

The Kenmore Elite washer model 11047798800 is a front-load design; most Kenmore Elite front-load washers of this generation are typically about 4.0 to 4.5 cu. ft. capacity. For the exact rated capacity for your specific unit, check the model specifications in the 11047798800 owner's manual.

We recommend using the manual first because it lists the official specs tied to your model number.

• Look for a Specifications section (often near the front or back of the manual)
• Check for terms like capacity, tub volume, or IEC capacity
• Match the model number exactly: 11047798800
• If you are comparing units, note whether the spec is listed as DOE or IEC capacity

Capacity is a tub-volume rating; it helps you estimate what fits without overloading (which can cause poor cleaning, vibration, and longer cycle times).

Using the right load size helps your 11047798800 wash more efficiently and reduces unbalanced loads that can extend cycle time. The manual also notes cycles can run longer if the washer detects oversudsing or an unbalanced load.

Last updated: February 2026

To hard reset your Kenmore Elite washer model 11047798800, unplug it (or switch off the breaker) for about 1 minute, then restore power. This clears many control glitches without changing the washer’s cycle options or settings stored in the control.

• Press STOP twice to cancel the current cycle.
• Unplug the washer (or turn the breaker off).
• Wait 60 seconds.
• Plug back in (or turn the breaker on).
• Select a cycle and press START (hold about 1 second) to begin.

For model-specific control behavior and cycle cancel steps, follow the 11047798800 owner's manual.

If the washer will not respond, we use the built-in cancel sequence first:

• Select STOP twice to cancel.
• If needed, select POWER.
• Re-select your cycle and options.
• Select and hold START (about 1 second) to restart.

If the door stays locked because water level or temperature is high, the washer may drain before unlocking. You can also:

• Select STOP twice.
• Select POWER.
• Select DRAIN & SPIN.
• Select and hold START (about 1 second).

A hard reset is a fast, safe first step for electronic control glitches. If the issue returns quickly, the problem is usually not the control memory; it is commonly a door lock, water supply issue, or a mechanical problem that needs troubleshooting.

Last updated: February 2026

To force your Kenmore Elite washer model 11047798800 to drain, cancel the current cycle and run Drain & Spin. On this model, we do that by pressing STOP twice, selecting POWER, choosing DRAIN & SPIN, then pressing and holding START for about 1 second. See the steps in the 11047798800 owner's manual.

• Press STOP twice to cancel the wash cycle.
• Press POWER.
• Select DRAIN & SPIN.
• Press and hold START for about 1 second to begin draining.
• Wait for the spin to finish; the door unlocks when the cycle completes.

If Drain & Spin starts but water stays in the drum, we check the most common causes first:

• Make sure the drain hose is not kinked, crushed, or pinched behind the washer.
• Confirm the standpipe or laundry tub drain is not clogged.
• Verify the drain hose is routed correctly; it should be secure but still allow an air gap.
• Inspect hoses for bulges, cuts, wear, or leaks and replace if needed.
• If you recently moved the washer, confirm the drain hose is not trapped in shipping clips.

Improper drain hose routing can cause slow draining or water to siphon back into the washer.

If the issue is physical (leak, loose connection, or a hose problem), these model-matched parts are commonly related:

• Washer tub-to-pump hose WPW10467168 (internal drain path)
• Washer fill hose WP89503 (supply side, but leaks can mimic drain issues)
• Clamp WP285655 (helps seal hose connections)

Running Drain & Spin is the safest way to remove water because it uses the washer’s normal drain routine and helps the door unlock properly when the cycle is complete.

Last updated: February 2026

Yes, repairing a Kenmore Elite washer like model 11047798800 is usually worth it when the fix restores reliable operation for less than the cost of replacing the washer. It is especially worthwhile for common, repairable issues such as leaks, door sealing problems, or excessive vibration.

We use these factors to decide quickly:

• Age and condition: If the tub, drum, and cabinet are in good shape, repairs tend to pay off.
• Type of failure: Wear items (seals, hoses, clamps, door boot) are typically cost-effective repairs.
• Repeat problems: Frequent leaks or recurring error conditions can point to multiple worn parts.
• Labor complexity: Some repairs are straightforward; others require major disassembly.
• Performance needs: If you rely on features like Steam Sanitize, keeping the machine running can be a strong value.

Front-load washers commonly develop leaks and door-seal issues. For model 11047798800, these parts are typical “high value” repairs:

• Door boot leak or mold damage: bellow WP8182119
• Door boot clamp issues: washer door boot spring clamp WP8182210
• Tub-to-pump leak: hose WPW10467168
• Fill problems (slow fill, no fill): washer water inlet valve WPW10156253
• Excessive shaking or banging: washer shock absorber W10822553

A targeted repair can prevent secondary damage (flooring, bearings, wiring) and keep cycles running correctly. This model’s cycle logic can extend time for oversudsing or unbalanced loads, so fixing the root cause helps performance and reduces repeat interruptions.

• Check troubleshooting and maintenance guidance in the owner's manual.
• Confirm the symptom (leak location, noise type, when it happens in the cycle).
• Price the likely parts first, then compare to replacement cost.

Last updated: February 2026

Most Kenmore washers last 10 to 15 years. For a Kenmore Elite washer like model 11047798800, lifespan depends mainly on load size, how often you run cycles, and routine care; consistent cleaning and correct installation help you reach the full service life (or more). See the owner's manual for model-specific care and operating guidance.

A washer’s life is usually determined by wear on the drive system, suspension, seals, and water-handling parts.

• Usage frequency: multiple loads per day shortens life faster than a few loads per week
• Overloading: increases stress on the motor, shocks, and tub support
• Detergent choice: using HE detergent helps prevent oversudsing and residue
• Leveling and stability: reduces vibration and “walking” that damages components
• Water quality and temperature: hot water and mineral buildup can accelerate seal and hose wear

These habits reduce common failure causes like oversudsing, leaks, and out-of-balance spinning.

• Use high-efficiency (HE) detergent and measure carefully
• Leave the door ajar between loads to help the bellow dry
• Wipe the door seal area and check for small items after each wash
• Keep the washer level to reduce vibration and suspension wear
• Don’t ignore early symptoms (new noises, small leaks, longer cycle times)

On front-load designs, leaks and vibration are two of the most common age-related issues.

A washer that is maintained and kept stable runs quieter, cleans better, and avoids secondary damage (for example, a small door-seal leak can lead to corrosion or bearing wear if it’s left unchecked).

Last updated: February 2026