Kenmore Elite 66513793K600 dishwasher Parts

Common problems on Kenmore dishwashers (including Kenmore Elite model 66513793K600) include not starting, stopping mid-cycle, not draining, poor cleaning, and door or rack issues. Many of these come down to power, water supply, latching, or a worn pump, valve, or control component.

• Won’t start or stops during a cycle: door not fully latched, cycle not set correctly, power interruption, tripped breaker or blown fuse
• No water or low fill: water shutoff valve closed, inlet valve issue, household water supply problem
• Not draining: clogged drain path, kinked drain hose, failed drain pump
• Poor cleaning: loading issues, spray arm blockage, filter or sump buildup, low water temperature
• Door problems: latch alignment, hinge wear, installation leveling issues

These checks match the basic “does not operate” troubleshooting steps in the installation and use-and-care guidance:

• Reset the house breaker or replace the house fuse if needed
• Confirm the door closes tightly and latches
• Re-select a cycle and press Start, then avoid opening the door right away
• Verify the water supply valve under the sink is fully open
• Start the shortest cycle and check for water in the bottom of the tub after a couple minutes (per the installation guide)

If the quick checks don’t solve it, these model-matched parts are frequent culprits:

Catching the root cause early prevents repeat cycle failures, standing water odors, and unnecessary wear on the pump motor and electronic control board.

• If you’re seeing blinking lights or a fault code, use Kenmore 665 model dishwasher error codes to narrow the problem to a specific system.

Last updated: January 2026

On the Kenmore Elite dishwasher model 66513793K600, the filter is located in the bottom of the dishwasher tub, directly under the lower spray arm area. You typically access it by pulling out the lower rack, then lifting or twisting the filter assembly out for cleaning; reinstall it fully seated before running a cycle.

• Turn the dishwasher off; let the wash water cool if it was recently running.
• Pull the lower dishrack straight out and set it aside.
• Look in the sump area at the bottom of the tub (center or slightly rear); the filter assembly sits there.
• Remove the filter (many Kenmore 665-style filters unlock with a short twist, then lift out).
• Rinse under warm running water; use a soft brush for stuck-on debris.
• Reinstall the filter so it locks in place; a loose filter can cause poor cleaning and drainage issues.

For diagrams and model-specific component locations, use the 66513793K600 owner’s manual.

This model family also uses a soil removal and filtration system; some parts are not meant to be removed every wash.

A clogged or incorrectly installed filter can leave food debris on dishes, reduce water flow to the spray arms, and contribute to draining complaints. Keeping the filter clean is one of the fastest ways to restore normal wash performance.

• Check the lower spray arm holes for clogs.
• Run a hot cycle with dishwasher cleaner or a vinegar rinse (per the troubleshooting guidance in the manual).
• If water remains in the tub, inspect the drain path and consider the drain components.
• For a drain-related repair on this model, the dishwasher drain pump WPW10348269 and dishwasher drain hose 8269144A are common service parts.

Last updated: January 2026

Kenmore Elite dishwasher model 66513793K600 is a Whirlpool-built Kenmore dishwasher. The 665 model prefix is the key identifier that ties this unit to Whirlpool manufacturing, even though the brand on the door is Kenmore.

Use these quick checks to verify you are working with the correct platform when ordering parts or troubleshooting:

• Look at the model tag inside the tub and confirm it reads 66513793K600
• Use the 665 prefix as the manufacturer identifier (Whirlpool-built Kenmore)
• Match parts by model number, not just “Kenmore Elite dishwasher”
• Use the wiring and component locations shown in the 66513793K600 owner’s manual
• Follow mounting and hookup details in the 66513793K600 installation guide

Kenmore is a brand name; different manufacturers built different Kenmore dishwashers over the years. Knowing that 66513793K600 is Whirlpool-built helps you:

• Choose compatible components (pump, motor, inlet valve, control)
• Use the right diagnostic steps and error-code logic for this design
• Avoid ordering look-alike parts that do not fit your tub, rack, or harness

These are examples of part types you will commonly replace on Whirlpool-built Kenmore 665 dishwashers:

If you are troubleshooting lights blinking or a cycle that will not run normally, use Kenmore 665 model dishwasher error codes to narrow the failure to a specific system (fill, heat, drain, or control).

Last updated: January 2026