Kenmore 10659429800 side-by-side refrigerator Parts

On Kenmore model 10659429800, a bad compressor usually shows up as poor cooling even though the refrigerator runs a lot, or repeated clicking as it tries to start. Because this model can normally run longer and make new sounds, we confirm a compressor problem by checking basic power and control issues first, then looking for consistent no-cool symptoms.

Many “bad compressor” complaints are caused by power, settings, or normal high-efficiency operation.

• Verify the power cord is plugged into a grounded 3-prong outlet.
• Check the outlet by plugging in a lamp.
• Reset a tripped breaker or replace a blown fuse.
• Make sure the temperature controls are turned on.
• If it was just installed or restarted, allow 24 hours to cool completely.
• Consider usage conditions that make it run longer (warm room, doors opened often, large food load).

For model-specific operating notes and troubleshooting steps, use the owner's manual.

These signs are more consistent with a compressor issue (especially when they persist after the checks above):

• Refrigerator and freezer both stay warm while the unit keeps trying to run.
• Repeated clicking from the start device area (start attempt, click off, repeat).
• Compressor is very hot to the touch after repeated start attempts (do not touch bare terminals).
• Little to no airflow or cooling improvement over several hours.

This model can make sounds that are normal, including buzzing (water valve), pulsating/high-pitched sounds (compressor and fans adjusting), and gurgling/rattling from refrigerant movement.

• Unplug the refrigerator for 5 minutes, then restore power and listen for a smooth start.
• Confirm both compartments are warming (not just one side).
• If you suspect a sealed-system or compressor electrical issue, have a qualified technician perform electrical and sealed-system checks.

A compressor is the heart of the sealed cooling system. Misdiagnosing it can lead to unnecessary part replacement, while catching a true compressor or start problem early can prevent extended warm temperatures and food spoilage.

Last updated: February 2026

On your Kenmore side-by-side refrigerator model 10659429800, the model number is printed on the model and serial tag, which you can typically find inside the fresh food (refrigerator) compartment when you open the refrigerator door. Use the tag information exactly as shown when ordering parts or checking specifications in the owner's manual.

Look for a paper or metal tag in one of these spots:

• Inside the refrigerator compartment on a side wall (often near the top front)
• Along the door frame (hinge side) when the fresh food door is open
• Behind the crisper drawers area (visible when drawers are removed)
• On the ceiling of the fresh food compartment near the light housing
• On the back exterior panel (less common, but worth a quick check)

Record these details so you can match parts correctly:

• Model number (for this unit: 10659429800)
• Serial number (helps identify production run details)
• Any type or code numbers listed (useful for service and parts lookups)

Kenmore model numbers can look similar across different refrigerator families. Using the exact model number from the tag prevents ordering the wrong water filter, ice maker, door gasket, or dispenser parts.

If you are ordering common maintenance items, this model’s parts list includes items like the genuine Kenmore refrigerator water filter EDR3RXD1 and other refrigerator parts matched to 10659429800.

Last updated: February 2026

A Kenmore 10659429800 side-by-side refrigerator usually stops cooling because power is interrupted, the temperature controls are set to OFF or too warm, or airflow is blocked between the freezer and fresh food sections. We also see cooling loss when the compressor or fans cannot run efficiently.

• Confirm the power cord is fully plugged into a grounded 3-prong outlet.
• Test the outlet with a lamp; reset the breaker or replace a blown fuse if needed.
• Make sure the refrigerator controls are ON and not turned to the OFF position.
• Check that air vents are not blocked by food packages (vents must stay open for proper circulation).
• After a new install or a major control change, allow 24 hours for temperatures to stabilize.

Your refrigerator depends on air moving between compartments; cold air enters the refrigerator section through the top vent and returns to the freezer. If vents are blocked, airflow is obstructed and temperature problems can occur.

Use this guide for control adjustments (wait at least 24 hours between changes):

For model-specific control locations and OFF position details, follow the 10659429800 owner's manual.

Sometimes the refrigerator is cooling, but water or ice symptoms make it seem like it is not working normally.

• If the ice maker is on, a buzzing sound during fill is normal (water valve opening).
• If you have weak water flow or no ice, a restricted filter can contribute to poor dispenser performance; replace the genuine Kenmore refrigerator water filter EDR3RXD1 on schedule.
• If you suspect a water supply problem to the ice maker or dispenser, the refrigerator inlet valve W10408179 is a common service part.

Related help: how to prevent water dispenser and ice maker problems.

When cooling stops, food safety and freezer performance can be affected quickly. Power, control settings, and airflow are the highest-impact items to check first because they can stop cooling without any parts failure.

Last updated: February 2026