Kenmore 79641382410 washer Parts

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 79641382410, consistent cleaning and basic maintenance (especially the drain system and inlet filters) helps you reach the upper end of that range; see the 79641382410 owner's manual.

Most washers land in the same general window, but these factors move the needle:

• Loads per week (more cycles equals faster wear)
• Overloading (stresses the drive system and suspension)
• Detergent use (too much can cause residue and odors)
• Water quality (hard water increases mineral buildup)
• Maintenance habits (cleaning filters, dispenser, and door seal)

The 79641382410 manual calls out routine cleaning tasks that directly reduce strain on key components.

• Run the Clean Washer routine as recommended
• Clean the door seal and glass to prevent leaks and odor
• Clean the dispenser to prevent clogs and poor rinsing
• Clean the water inlet filters to maintain fill performance
• Clean the drain pump filter to prevent slow/no-drain problems

Some problems are inexpensive fixes; others signal major wear.

If you’re dealing with a drain issue, the drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T is a common wear item to inspect after you clean the drain pump filter.

Knowing the 10 to 15 year lifespan helps you decide when maintenance and a targeted part replacement makes sense versus planning for a replacement washer, especially if multiple major components start failing close together.

Last updated: February 2026

On Kenmore washer model 79641382410, we force a drain by pausing the cycle, then running a drain-and-spin using the control panel: press POWER, press SPIN SPEED (with no cycle selected), then press START/PAUSE to pump the water out and spin. See the 79641382410 owner's manual.

• Press START/PAUSE to pause the washer.
• If the door stays locked, wait; the door unlocks only when water level and temperature are safe.
• Press POWER to stop the cycle.
• Press SPIN SPEED (do not select a wash cycle).
• Press START/PAUSE; the washer should drain, then spin.
• When finished, press POWER.

A no-drain condition is usually a restriction (hose, filter, or pump) or a failed drain pump.

• Confirm the drain hose is not kinked, pinched, crushed, or stretched.
• Make sure the standpipe or drain height is not higher than 96 in. above the bottom of the washer.
• If the hose is pushed too far into a standpipe, pull it back; typical insertion is 8 to 12 in.
• If you use an extension, keep it short; long extensions can cause poor draining.
• If you hear the pump hum but water does not move, inspect the pump and hoses for a blockage.

If the washer consistently will not drain (or drains very slowly) after hose and drain setup checks, the drain pump is a common fix.

Forcing a proper drain protects the door lock system, prevents overflow risk from an unsecured drain hose, and helps the washer reach high-speed spin so clothes come out less wet.

Last updated: February 2026

Yes. Your Kenmore washer model 79641382410 is equipped with a drain pump filter that traps lint and small items (coins, buttons, keys) to help protect the drain pump and improve draining performance. The cleaning steps and access location are shown in the 79641382410 owner's manual.

This model uses two common filter points that affect filling and draining:

• Drain pump filter: catches debris before it reaches the pump
• Water inlet hose screens: small screens at the water valve connections that catch sediment
• Dispenser area: not a “filter,” but buildup here can affect water flow into the tub

We recommend cleaning the drain pump filter anytime you have slow draining, standing water, or a musty odor.

• Unplug the washer.
• Open the drain pump filter access panel.
• Pull out the small drain hose, remove the plug, and drain water into a shallow pan.
• Twist the pump filter counterclockwise to remove it.
• Remove lint and foreign objects; rinse the filter.
• Reinstall the filter (turn clockwise), reinstall the plug, and close the access panel.

If you need the replacement pump motor for drain problems, use the exact match for this model: drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T.

A clogged drain pump filter can cause poor draining, longer cycle times, and extra strain on the drain pump. Keeping the filter clean helps your Kenmore washer run quieter and reduces the chance of water left in the drum.

Last updated: February 2026

On the Kenmore washer model 79641382410, the model and serial number are printed on an identification plate inside the washer door (typically on the door opening or door jamb area). We use that exact model number to match the correct parts and troubleshooting info.

• Open the washer door and look around the door opening for a rating label
• Check the door jamb area (the cabinet frame the door closes against)
• Look along the inner front panel near the latch area
• If the label is hard to read, use a flashlight and wipe the area with a damp cloth

The identification plate typically lists:

• Model number (for example, 79641382410)
• Serial number
• Electrical ratings (voltage/amps)
• Sometimes a manufacturing date code

The model number is the key to getting the right Kenmore washer parts and repair instructions. Even small model-number differences can change which door lock, drain pump, or water inlet valve fits.

• Write down the full model number and serial number exactly as shown
• Use the model number to confirm part fit before ordering
• For model-specific diagrams and identification help, check the 79641382410 owner’s manual

Last updated: February 2026

A bottom leak on Kenmore washer model 79641382410 usually comes from a loose or damaged drain path (tub-to-pump hose, pump, or clamps) or a door boot leak that runs down the front frame and drips underneath. We start by checking hoses, the drain pump area, and the door seal.

• Unplug the washer; turn off both water supply faucets.
• Pull the washer forward and look for a trail: front-center (door area) vs. back (hoses) vs. middle (pump).
• Check the standpipe or laundry tub for overflow; a slow drain can make water back up.
• Confirm the drain hose is installed correctly (not shoved too far into the standpipe and not too high); see the 79641382410 owner's manual.
• Run a short Rinse/Spin with no clothes and watch where the first drip appears.

A small leak can quickly damage flooring and can also lead to poor draining or spin performance if water is escaping from the pump or drain hose setup. The manual also notes drain height and insertion limits that help prevent drain problems that can look like leaks.

• If the leak is at the pump housing or you see water at the pump during drain, the pump assembly is the most common repair.
• If the leak tracks from the door opening, the door boot is the most common repair.
• If the leak appears only during fill, focus on inlet hoses and the inlet valve.

Last updated: February 2026

The tub capacity (cubic feet) for Kenmore washer model 79641382410 is listed in the product specifications in the Use & Care Guide; use the spec table in the 79641382410 owner's manual to get the exact cu. ft. value for your unit.

Use the model tag and the specifications pages so you match the correct 796-series washer.

• Open the door and locate the model and serial label inside the door opening
• Confirm the full model number is 79641382410 (not the shortened 796.4138 prefix)
• In the manual, look for Key dimensions and specifications or a Specifications table
• Find the line for capacity (sometimes shown as “tub capacity” or “volume”)
• Record the value in cu. ft. for future reference when choosing load size

Most Kenmore 796 front-load washers fall into a mid-to-large capacity range; the manual gives the exact number for 79641382410.

Capacity affects how full the drum should look during washing. Correct loading improves tumble action, rinsing, and spin balance; overloading increases vibration and can contribute to out-of-balance conditions.

Last updated: February 2026