Kenmore 11072722100 gas dryer Parts

To hard reset a Kenmore 11072722100 gas dryer, unplug it (or switch off the breaker) for 5 minutes, then restore power and start a timed cycle. This clears many control and cycle-selection glitches; if it still will not run, focus on the door switch, power supply, and airflow.

Hard reset steps (safe, effective)

• Turn the dryer OFF.
• Unplug the power cord (or turn OFF the circuit breaker).
• Wait 5 minutes.
• Restore power.
• Set the timer to a timed dry cycle and press PUSH TO START.
• If the dryer stops when you open the door, close the door firmly and press PUSH TO START again (this matches normal operation described in the 11072722100 owner's manual).

If the reset does not fix it

These checks solve most “dead” or “won’t start” complaints after a reset:

• Confirm the outlet has power; reset the breaker or replace a blown fuse.
• Close the door firmly; a misaligned door can keep the motor from running.
• Test the door switch; a failed switch can act like the door is always open (see dryer door switch WP3406107).
• Clean the lint screen and verify strong airflow at the exhaust; restricted venting can cause overheating and shutdowns.
• If the drum does not turn but the motor hums, inspect the belt and idler (see dryer drum belt 341241 and idler pulley WP691366).

Quick symptom guide

What you see	Most likely cause	What to do next
No lights, no response	Power supply issue	Check breaker, outlet, fuse type
Runs only with door held	Door switch/door strike issue	Inspect latch alignment; test switch
Hums, drum not turning	Belt or idler problem	Inspect belt routing and pulley
Starts then stops quickly	Airflow restriction or overheating	Clean lint screen, vent, blower area

Why it matters

A hard reset only clears temporary control or cycle-selection issues. If a safety device or start circuit component (like the door switch or belt system) is failing, the dryer will keep refusing to run until the underlying problem is corrected.

Last updated: February 2026

On a Kenmore dryer, an F1 code typically points to a control problem (the electronic control board is detecting an internal fault). On model 11072722100, start by resetting power and checking wiring connections to the control before replacing parts.

Quick checks we recommend first

• Unplug the dryer (or switch off the breaker) for 5 minutes, then restore power and try a cycle.
• Confirm the dryer is getting proper power (a weak or intermittent supply can trigger false errors).
• Check for a stuck key or damaged console area (if your model has electronic buttons).
• Inspect visible wire harness connections for looseness or corrosion at the control area.
• If the code returns immediately, plan for deeper diagnosis using the wiring diagram and troubleshooting steps in the 11072722100 owner's manual.

What usually causes the F1 code

In most Kenmore dryers, F1 is tied to the main control detecting a failure such as a bad control board circuit, a communication issue, or a shorted input.

Symptom	Most likely area	What to do next
F1 appears as soon as you power on	Control board or console input	Reset power; inspect harnesses; test/replace control if needed
F1 appears mid-cycle	Intermittent connection or control overheating	Check connections; verify airflow and venting; retest
F1 comes and goes	Loose harness, vibration-related issue	Reseat connectors; look for rubbed-through wires

Why it matters

When the control senses an internal fault, the dryer may stop to prevent unsafe operation. Clearing the underlying issue helps restore reliable starting, heating, and cycle completion.

Related help

If your dryer displays other codes or you want a code reference by Kenmore series, use our Kenmore 110 series electronic control model dryer error codes guide.

Last updated: February 2026

Your Kenmore gas dryer’s model number is printed on the model and serial number plate. On model 11072722100, you’ll find that plate in the door well area; open the dryer door and look around the opening for the label. See the 11072722100 owner's manual for the exact label location and examples.

Where to look on the dryer

Check these common label spots first:

• Inside the door opening (door well) on the front panel
• On the door frame itself
• Just behind the door opening on the cabinet face
• Occasionally on the side panel near the front edge

What to write down (and why)

Record both numbers exactly as shown:

• Model number (used to match parts and diagrams)
• Serial number (used to identify production details)
• Date of purchase (helpful for your records)

Quick reference

Item	What it’s used for	Example of what it looks like
Model number	Finding correct Kenmore 11072722100 parts	11072722100
Serial number	Identifying your unit’s build info	Letters and numbers

Why it matters

Using the full model number prevents ordering the wrong dryer parts (like a belt, door switch, or thermostat) and helps us match the correct diagrams and troubleshooting steps for your exact Kenmore gas dryer.

Last updated: March 2026