Kenmore 79576203901 refrigerator Parts

To tell what model Kenmore refrigerator you have, we look for the model and serial tag on the cabinet (not on a removable drawer). On Kenmore model 79576203901, the tag is typically inside the fresh food section or freezer area on an interior wall, or near the lower front behind the toe grille.

Where to look for the model number tag

Check these common locations first (use a flashlight and look for a sticker or metal plate):

• Inside the refrigerator compartment on a side wall (often near the crisper area)
• Inside the freezer compartment on a side wall or back wall
• On the door frame area (visible when the door is open)
• Behind the lower toe grille (kick plate) at the front of the refrigerator
• Behind or beside the lower crisper drawer area on the cabinet wall

What the tag looks like and what to write down

The label usually includes a model number and serial number. For parts lookup and troubleshooting, we use the model number first.

You see on the label	What it means	Example
Model / Model No.	Identifies the exact refrigerator design	79576203901
Serial / S/N	Production code used for manufacturing date and revisions	Letters and numbers

Tips to avoid common mix-ups

• Use the full model number exactly as printed (include all digits).
• Don’t use numbers from the ice maker, water filter, or control board labels; those are part numbers.
• If the label is worn, take a close-up photo and zoom in to confirm characters.

Why it matters

We match parts, diagrams, and repair steps to the exact model. Even within Kenmore 795-series bottom-mount refrigerators, small design changes can affect which door switch, ice maker, or water inlet valve fits.

For model-specific identification notes and label locations, use the 79576203901 owner’s manual.

Last updated: February 2026

The exact cubic-foot capacity for Kenmore refrigerator model 79576203901 is listed on the model’s rating label and in the 79576203901 owner's manual. Most Kenmore 795 (LG-built) bottom-mount refrigerators are commonly in the low-to-mid 20 cu. ft. range, but the label gives the precise number for your unit.

Where to find the exact capacity on your refrigerator

Check these spots first (no tools needed):

• Inside the fresh food compartment on a side wall near the crisper area
• Ceiling area inside the refrigerator section near the light housing
• Behind the crisper drawers (sometimes visible after removing the drawers)
• On the back exterior near the lower service area (less common)

On the label, look for wording like “Total capacity”, “Total volume”, or “cu. ft.”.

What “cubic feet” means (and why it matters)

Cubic feet is the total interior storage volume of the refrigerator and freezer combined. It helps you compare:

• How much food the refrigerator holds
• Whether a replacement refrigerator will fit your household needs
• Cooling load expectations (larger capacity typically means longer run times)

Typical capacity ranges for similar Kenmore bottom-mount models

We use this as a practical comparison when you are shopping or estimating space needs.

Refrigerator style	Typical total capacity	Notes
Bottom-mount (standard depth)	20 to 25 cu. ft.	Most common range for many 795 models
Bottom-mount (counter-depth)	18 to 22 cu. ft.	Shallower cabinet depth reduces volume
French door (standard depth)	25 to 30+ cu. ft.	Often larger overall footprint

Quick tip if you are matching parts or accessories

When ordering parts (like an ice maker or water inlet valve), use the full model number 79576203901, not the capacity. Capacity helps with shopping, but model number ensures correct fit.

Last updated: February 2026

A bad compressor in your Kenmore 79576203901 bottom-mount refrigerator usually shows up as poor or no cooling even though the unit has power, often paired with repeated clicking (start attempts) or the compressor running nonstop. We confirm the diagnosis by checking airflow, temperatures, and the compressor start components before condemning the compressor.

Quick symptoms checklist

• Fresh food and freezer both warm (or warming) while lights and controls still work
• Repeated clicking every few minutes from the back (start relay trying and failing)
• Compressor is very hot to the touch after running attempts (use caution)
• Compressor is silent and never starts, even though fans may run
• Frost pattern is abnormal (little to no frost on the evaporator) and cooling is weak

What to check first (most common causes)

Before replacing a compressor, we rule out easier, more common failures that mimic a “bad compressor”:

• Condenser airflow: clean condenser coils and confirm the condenser fan runs
• Evaporator airflow: confirm the evaporator fan runs and vents are not blocked
• Defrost system: heavy frost buildup can stop airflow and cause warm temps
• Start device: a failed start relay/overload can cause clicking and no start
• Power and control: verify steady outlet power and no loose wiring at the compressor

For model-specific access panels, component locations, and wiring guidance, use the 79576203901 owner’s manual.

Simple decision guide

What you observe	Most likely cause	What we do next
Clicking + compressor not running	Start relay/overload issue	Test start device, wiring, compressor windings
Compressor runs constantly + warm temps	Sealed system or compressor inefficiency	Check condenser airflow, then sealed system indicators
Compressor very hot + shuts off	Overload trip from hard start or restriction	Test start device, check airflow and amp draw
Fans not running + warm temps	Fan motor or control issue	Verify fan operation and control outputs

Parts that commonly relate to compressor “no cool” complaints

These parts are often involved in diagnosing cooling failures on this model:

• Refrigerator compressor TCA35931726 (if the compressor itself has failed)
• Refrigerator compressor start relay EBG32606502 (common clicking/no-start cause)
• Refrigerator condenser fan motor EAU61644105 (poor heat removal can mimic compressor trouble)

Why it matters

Replacing a compressor is one of the most expensive refrigerator repairs, and the symptoms overlap with airflow, defrost, and start-device problems. A step-by-step diagnosis prevents replacing the wrong part and gets cooling restored faster.

Last updated: February 2026

Common problems we see on Kenmore Elite refrigerators like model 79576203901 include warm temperatures (cooling failure), ice maker not making ice, water leaks, and door sealing issues. These symptoms usually trace back to airflow restrictions, defrost system trouble, water supply/valve problems, or worn door gaskets; our 79576203901 owner's manual helps confirm the correct checks for your exact configuration.

Most common symptoms and likely causes

• Not cooling or weak cooling: dirty condenser coils, failed condenser fan motor, failed evaporator fan motor, frost buildup from a defrost failure
• Ice maker not working: frozen fill tube, low water pressure, failed inlet valve, failed ice maker assembly
• Water leaking or puddles: clogged/iced drain path, cracked drain tube, mis-seated water line connections
• Door not closing or sweating: torn/warped gasket, hinge wear, door alignment issues
• Lights or controls acting up: door switch problems, control/display board issues

Quick troubleshooting checklist (safe DIY)

1. Set temps to typical targets: 37°F fresh food and 0°F freezer.
2. Make sure vents are not blocked by food packages.
3. Clean condenser coils (unplug first); restricted coils cause warm temps and long run times.
4. If you hear clicking or buzzing near the back, check the start components and airflow at the condenser area.
5. For leaks, inspect the drain area and tubing for ice or debris.

Parts that commonly fix these issues on 79576203901

Symptom	Common part to check	Example part for this model
No ice	Ice maker assembly	Ice maker kit AEQ72909603
No ice or slow fill	Water inlet valve	Refrigerator water inlet valve assembly AJU55759303
Frost buildup, warm fridge	Defrost sensing	Refrigerator defrost sensor assembly 6615JB2005C
Door ajar light, no light	Door switch	Lg refrigerator door switch 6600JB1010A
Sweating, poor seal	Door gasket	Refrigerator door gasket ADX73350927

Why it matters

Cooling, ice, and leak problems often share the same root causes: restricted airflow, failed fans, or water system restrictions. Catching them early helps prevent food spoilage, ice buildup, and floor damage.

Helpful model-specific DIY reference

• Use Kenmore 795 model bottom freezer refrigerator error codes if your display shows an error; it speeds up diagnosis before replacing parts.

Last updated: February 2026

Most Kenmore Elite refrigerators, including Kenmore model 79576203901, last 12 to 15 years with normal household use. Consistent maintenance (clean airflow, good door sealing, stable temperatures) pushes life toward the high end; neglected cleaning and heavy use shorten it.

Typical lifespan and what changes it

A refrigerator’s life is mainly driven by compressor run time, heat removal, and how well the doors seal.

• 12 to 15 years is the typical range for modern refrigerators
• 10 years or less is common with dirty condenser coils, frequent door openings, or warm room temps
• 15+ years is common when coils are kept clean and seals stay tight
• Ice maker and water system parts often need service before the sealed system does

Maintenance checklist that adds years

Use these habits for a Kenmore bottom-mount like 79576203901:

• Vacuum and brush condenser coils and the front or rear air intake every 6 to 12 months
• Keep freezer at 0°F and fresh food at 37°F to 40°F
• Confirm doors close on their own and gaskets fully contact the cabinet
• Leave space around the refrigerator for airflow (especially behind and above)
• Replace worn door-switch or gasket parts promptly so the unit does not run constantly

Parts that commonly affect “lifespan” (repairable items)

If the refrigerator is running warm, making ice slowly, or running nonstop, these model-matched parts are common suspects:

Symptom	Common cause	Example model-matched part
Frost buildup, warm temps	Defrost system issue	Refrigerator defrost sensor assembly 6615JB2005C
Ice maker not filling or slow ice	Water supply/valve issue	Refrigerator water inlet valve assembly AJU55759303
Door ajar alarm, lights act odd	Door switch issue	Lg refrigerator door switch 6600JB1010A

Why it matters

Knowing the expected lifespan helps you decide when a repair is a smart investment. If your 79576203901 is under about 12 years old, fixing a single failed part (ice maker, valve, sensor, fan) is typically the best value compared to replacement.

For model-specific care steps and cleaning guidance, follow the 79576203901 owner’s manual.

Last updated: February 2026

On the Kenmore 79576203901 bottom-mount refrigerator, the “bottom part” is usually called the machine compartment (or lower rear compartment) on the outside, and the freezer drawer on the inside. The machine compartment area typically contains the compressor and other cooling-system components behind a lower cover.

Common names you’ll hear (and what they mean)

• Machine compartment: The service area at the bottom/back where major cooling parts live.
• Kickplate (or toe grille): The lower front cover on some refrigerators that helps with airflow and access.
• Freezer drawer: The bottom storage section inside a bottom-mount refrigerator.
• Drain pan area: A lower area where defrost water can evaporate.
• Condenser area: Where heat is released (often near the compressor and condenser fan).

What’s typically located in the bottom area

Bottom area	What it usually contains	Why it matters
Inside bottom (freezer)	Drawer, slide rails, bins	Storage and door sealing affect temps
Outside bottom/back (machine compartment)	Compressor, fans, relays, wiring	Drives cooling and heat removal
Lower front cover (if equipped)	Air intake path, access point	Poor airflow can reduce cooling

Parts that commonly relate to “the bottom” on this model

If you’re troubleshooting a noise, warm temps, or icing, these model-matched parts are often involved:

• Refrigerator compressor TCA35931726 (cooling system pump)
• Refrigerator compressor start relay EBG32606502 (helps the compressor start)
• Refrigerator drain tube 5251JA3003D (routes defrost water away)
• Refrigerator freezer drawer slide rail, right 5218JA1010E (supports freezer drawer movement)

Why it matters

Using the right term helps you find the correct diagram and part faster. For example, “freezer drawer” points to rails and bins, while “machine compartment” points to the compressor, condenser fan, and electrical start components.

Where to confirm the exact names for your unit

We list the official component names and locations for Kenmore 79576203901 in the 79576203901 owner's manual.

Last updated: February 2026

Ice on the bottom of the freezer in your Kenmore 79576203901 almost always happens when defrost water cannot drain away; it pools under the evaporator area, runs to the freezer floor, and freezes into a sheet. Clearing the defrost drain and restoring proper airflow stops the repeat buildup.

Most common causes

• Defrost drain clogged with ice, food debris, or sludge
• Drain tube restricted or out of position (water misses the drain path)
• Door not sealing well, causing excess frost that overwhelms the drain
• Freezer overpacked, blocking vents and increasing frost
• Defrost system issue creating heavy frost that melts into excess water

Quick checks you can do first

1. Unplug the refrigerator and remove the freezer drawer/bins.
2. Look for a solid ice sheet on the freezer floor or a frozen trough under the rear panel.
3. Melt the ice with a hair dryer on low or warm towels (keep heat moving; do not overheat plastic).
4. Flush the drain with hot water using a turkey baster; repeat until it flows freely.
5. Confirm the drain tube is clear and seated; on this model, the external drain path commonly uses a drain tube like the refrigerator drain tube 5251JA3003D.

What to replace if the problem keeps coming back

If you clear the drain and ice returns within days to a couple of weeks, a part may be restricting drainage or increasing frost.

Symptom you notice	Most likely area	What to check next
Water refreezes after every defrost	Drain path	Drain tube for blockage or kinks; drain opening for ice plug
Heavy frost on back wall	Defrost system	Defrost heater and sensor operation
Frost near door edges, moisture	Door seal	Gasket gaps, torn corners, door alignment

Model-matched parts that often relate to this issue include the refrigerator drain tube 5251JA3003D and, when heavy frost is present, the refrigerator defrost sensor assembly 6615JB2005C or refrigerator defrost heater 5300JB1100J. For panel removal and safe access steps, follow the 79576203901 owner's manual.

Why it matters

A blocked drain can lead to recurring ice sheets, drawer rails binding, water leaks, and temperature swings that affect food quality. Fixing the drain and any underlying frost cause prevents repeat freeze-ups.

Last updated: February 2026

Water pooling in the bottom of your Kenmore refrigerator model 79576203901 is typically caused by a clogged or frozen defrost drain, which forces defrost water to spill into the fresh food compartment instead of flowing to the drain pan. We fix this by clearing the drain path and checking for ice buildup.

Quick checks (most common causes)

• Clogged defrost drain hole from food debris or sludge
• Frozen drain tube from repeated door openings or warm, humid air
• Drain pan shifted or cracked (water misses the pan)
• Door not sealing well, creating excess frost that overwhelms the drain
• Fridge not level, causing water to run forward instead of toward the drain

Step-by-step: clear a clogged or frozen defrost drain

1. Unplug the refrigerator.
2. Remove the bottom bins/shelves so you can access the rear interior floor area.
3. Find the drain opening (usually at the back of the fresh food compartment floor or behind a rear panel).
4. Flush the drain with hot water using a turkey baster; repeat until it drains freely.
5. If it refreezes quickly, thaw the drain tube longer (a hair dryer on low works; keep heat moving).
6. Confirm water is reaching the drain pan underneath.

For model-specific access panels and drain location, follow the 79576203901 owner's manual.

Parts that commonly relate to this symptom

If clearing the drain does not stop the leak, these parts are frequent next checks:

Symptom you see	Likely area	Example part for this model
Water returns after a day or two	Defrost system creating heavy frost	Refrigerator defrost sensor assembly 6615JB2005C
Sheet of ice on freezer floor	Defrost drain freezing in freezer section	Drain tube and drain path
Door sweat, frost, or recurring ice	Door seal not closing tightly	Refrigerator door gasket ADX73350927

Why it matters

Standing water can lead to odors, ice buildup, and temperature swings that stress the evaporator fan and defrost system. Fixing the drain early helps keep airflow steady and prevents repeat icing.

If you also have ice maker or dispenser issues, our how to prevent water dispenser and ice maker problems guide helps you rule out supply and freezing problems that can contribute to icing.

Last updated: February 2026