Kenmore 11098575120 washer/dryer Parts

To reset the washer on Kenmore model 11098575120, we power-cycle it: unplug the laundry center for 5 minutes, then plug it back in and start a new cycle. This clears many temporary control glitches and restores normal operation.

• Turn the washer control to Off.
• Unplug the power cord from the outlet.
• Wait 5 full minutes (this lets the control fully discharge).
• Plug the unit back in.
• Lift and close the lid once, then select a cycle and press Start.
• If the washer was mid-cycle, run a Rinse/Spin to confirm operation.

These checks solve the most common “no start” complaints on top-load Kenmore laundry centers:

• Confirm the outlet has power (test with a lamp).
• Make sure the lid is fully closed and the load is not pushing against it.
• Verify the water faucets are on; some cycles will not begin without water flow.
• If the washer fills but will not agitate, inspect the agitator dog 80040 (worn dogs can stop the agitator from grabbing).
• If the washer hums but will not agitate or spin, the coupling 285753A is a common failure point between the motor and transmission.
• If the tub will not drain, check for a clog at the pump and consider the washer drain pump WP3363394.

A proper reset rules out a simple control lockup before you spend time on deeper troubleshooting. If symptoms remain after the power-cycle, matching the symptom to the drive or drain system helps you target the right repair faster.

Last updated: February 2026

Most Kenmore washer and dryer sets, including stacked laundry centers like model 11098575120, typically last about 10 to 12 years with normal household use. Consistent maintenance (good airflow for the dryer and proper loading for the washer) is what most often determines whether you land closer to 10 years or push beyond it.

These ranges help set expectations for a Kenmore laundry center where the washer and dryer share a cabinet.

We recommend these practical habits because they prevent the most common wear issues (drive, drain, and heat).

• Keep dryer venting short, smooth, and clear; restricted airflow is the #1 cause of overheating and long dry times.
• Do not overload the washer; heavy loads strain the drive system and can accelerate clutch and gear wear.
• Use the right water level and detergent amount; oversudsing can contribute to poor draining and residue.
• Check fill hoses and the inlet screens yearly; slow filling can point to a clogged valve screen or a failing valve.
• Address new noises early (grinding, squealing, banging) before they damage multiple components.

If performance drops, these are some of the higher-impact parts customers often replace on Kenmore model 11098575120:

• Washer not draining or leaving water behind: washer drain pump WP3363394
• Washer not agitating well: agitator dog 80040
• Washer won’t spin or struggles under load: clutch 285785
• Dryer squeals or tumbles poorly: dryer idler pulley WP691366

Knowing the expected lifespan helps you decide whether to repair or replace. If your 11098575120 is under about 10 years old, a targeted repair (like a drain pump or idler pulley) often restores reliable operation. Past 12 years, multiple wear items can start stacking up, so it’s smart to prioritize the fix that solves the main symptom first.

Last updated: February 2026

Yes. Kenmore model 11098575120 is a stacked laundry center (washer and dryer in one unit), and we support it with replacement parts and repair help. If you are shopping for a new unit, use the model number to match fit and hookups before you buy.

Kenmore 11098575120 identifies a specific stacked washer/dryer laundry center, not a universal “110V stackable combo” product listing. When you search, include the full model number so you land on the correct Kenmore laundry center parts and diagrams.

• Find the model tag on the laundry center frame (often inside the washer lid area or on the dryer door opening).
• Match all digits: 11098575120.
• Compare the parts you need to common wear items for this platform.
• If the washer won’t agitate, check the agitator dog 80040.
• If the washer won’t drain, check the washer drain pump WP3363394.

Laundry centers use model-specific parts (agitator components, drain pump, dryer drive parts). Matching the exact model number prevents ordering a part that looks similar but will not fit or connect correctly.

• Unplug the laundry center and shut off water.
• Take a photo of the model tag and the failed part.
• Use basic test tools when needed; see must have tools for appliance repair.

Last updated: February 2026

Kenmore stacked laundry center model 11098575120 uses a compact, top-load washer inside the one-piece cabinet. For planning space, most Kenmore 110-series laundry centers are built in a 24 to 27 inch width class with an overall height commonly around 70 to 76 inches; measure your unit to confirm the exact cabinet dimensions.

Because the washer and dryer share one cabinet, the most useful “size” specs are the cabinet footprint and the washer tub capacity.

• Cabinet width class: typically 24 to 27 inches
• Cabinet depth: typically 27 to 32 inches (allow extra for venting and hoses)
• Overall height: typically 70 to 76 inches
• Washer capacity class: typically compact to mid-size for stacked units (agitator style)

Use a tape measure on the cabinet, not the washer basket.

• Measure width at the widest point (often the top or side panels)
• Measure depth from the back panel to the front edge (exclude knobs if they protrude)
• Measure height floor to the top of the cabinet
• Add clearance for fill hoses, drain hose, and dryer vent duct

Correct sizing prevents airflow restrictions (overheating and long dry times), hose kinks (fill or drain problems), and fit issues in closets or alcoves.

If you need to route the dryer exhaust to the side to fit your space, use the correct side-vent kit: amana laundry center dryer side exhaust extension kit 279823.

Last updated: February 2026