Kenmore 66517483300 undercounter dishwasher Parts

Yes. We still support parts for many Kenmore dishwashers, including Kenmore model 66517483300, as long as the specific replacement part is still produced and available. The key is matching the exact model number to the correct OEM-style part, such as a drain hose, door seal, or pump and motor assembly.

How to make sure you order the right part

Use the model number 66517483300 and confirm the part by name and ID before ordering.

• Match the full model number on the rating label to 66517483300
• Compare the part name to the symptom (leak, no drain, poor wash)
• Verify the part ID, not just a description
• Check for included hardware (clamps, gaskets) before you start
• Use the diagrams and part lists in the 66517483300 owner's manual

Common parts customers replace on this model

These are examples of parts currently listed for Kenmore 66517483300 that often solve common dishwasher problems:

Symptom	Part to check	Example part for this model
Won’t drain, slow drain	Drain path and hose routing	Dishwasher drain hose 8269144A
Leaks at the door	Door seal and alignment	Gasket W11196317
Poor wash, loud grinding	Circulation pump and chopper area	Dishwasher pump and motor assembly W10782773
Dead, no power	Fuse and wiring connections	Fuse 8193762

Why it matters

Dishwasher parts are highly model-specific. Even within Kenmore dishwashers, small design changes can affect fit, wiring connectors, and hose routing. Using the correct 66517483300 part ID helps prevent leaks, repeat failures, and installation headaches.

Quick install and safety checks after a repair

After replacing a part, we follow the same basic verification steps used during installation:

• Restore power at the breaker or fuse box
• Run the shortest wash cycle
• After about 2 minutes, open the door and confirm water is in the bottom
• Check underneath for drips during fill and drain
• Recheck clamps, seals, and mounting screws if you see moisture

For more detailed steps and checks, use the 66517483300 installation guide.

Last updated: February 2026

To identify your Kenmore dishwasher model, we look for the model and serial number label inside the door opening. On Kenmore model 66517483300, the label is typically on the inner door edge or on the tub wall near the front.

Where to look first (fastest checks)

• Open the door and inspect the top and side edges of the inner door frame.
• Look on the tub wall near the front opening (left or right side).
• Check near the control panel area if your unit has a top-control console.
• Wipe the area with a damp cloth; soap film can hide the print.
• Use a flashlight and look at an angle; labels can be reflective.

What the label looks like and what you need

The tag usually lists both a model number and a serial number. For parts lookup and troubleshooting, the model number is the key.

You see on the label	What it’s used for	Example for this page
Model number	Ordering correct parts and matching diagrams	66517483300
Serial number	Identifying production details and service records	Varies by unit

If the label is missing or unreadable

• Check the toe-kick area (behind the lower access panel) for a secondary tag.
• Look for paperwork from the original install; installers often record the model.
• Use the feature diagram in the 66517483300 owner’s manual to confirm you are working with the correct series (it shows the model/serial label location and common component names).

Why it matters

Kenmore dishwashers often share similar styling across multiple series, but parts like the door seal, drain hose, and pump assemblies can differ by model. Using the exact model number helps us match the right replacement part the first time.

Last updated: February 2026

Yes, repairing a Kenmore 66517483300 dishwasher is worth it when the fix is a common wear item (seal, hose, fuse, rack parts) or a single failed component; it is less worth it when multiple major systems are failing or the repair cost approaches the price of a replacement.

Quick way to decide (cost vs. value)

Use this simple rule of thumb for an undercounter dishwasher:

• Worth repairing: total repair cost is under ~50% of a comparable replacement
• Consider replacing: repair cost is over ~50%, or you have repeated leaks, poor cleaning, and electrical issues together
• Always check coverage: this model’s documentation describes multi-year warranty coverage and longer coverage on certain stainless steel tub models; confirm your purchase date and what is covered in the 66517483300 owner's manual.

What’s wrong	Typical outcome	Usually worth it?
Leak at door perimeter	Door seal or gasket replacement	Yes
Not draining	Drain hose restriction or routing issue	Yes
Dead/no power	Fuse or wiring issue	Often
Loud grinding/no wash	Pump/motor or chopper related	Depends

Repairs that are commonly cost-effective

These are the types of repairs we see pay off most often because they restore performance without replacing the whole dishwasher:

• Replace a leaking door seal such as gasket W11196317
• Fix drain problems by inspecting or replacing the dishwasher drain hose 8269144A
• Restore power by testing and replacing the fuse 8193762 (after checking wiring connections)
• Improve loading and rust issues by replacing rack components (for example, a lower rack or tine row)

Why it matters

A dishwasher repair is usually a good value when it stops leaks, restores draining, or brings the unit back to normal washing with one targeted part. The manual also emphasizes preventive maintenance and troubleshooting steps that can prevent repeat failures and unnecessary part replacement.

Before you buy parts (3 checks that prevent repeat repairs)

• Confirm the symptom: leak, no drain, no power, poor cleaning, or noise
• Do the basic maintenance: clean filters and check for obstructions in the sump area
• Verify installation basics: drain routing and air gap (if used) per the 66517483300 installation guide

Last updated: February 2026

Common problems we see with the Kenmore 66517483300 dishwasher include not running or stopping mid-cycle, not filling, running longer than expected, poor cleaning from buildup, and leaks around the door or hoses. Many issues start with simple checks in the 66517483300 owner's manual.

Most common symptoms and what they usually point to

• Dishwasher does not run or stops: door not fully latched, cycle not selected correctly, power issue (breaker or house fuse), or motor overload that resets after a few minutes.
• Will not fill: overfill protection float stuck; it must move freely up and down.
• Runs too long: normal pauses during the main wash, or a cycle option that extends run time.
• White film or odors: hard-water mineral buildup and interior residue.
• Water on the floor: door seal wear, vent gasket leaks, or drain hose routing issues.

Quick checks we recommend first (fast, no parts)

1. Confirm the door closes tightly and latches.
2. Verify the cycle selection and start procedure.
3. Check the home breaker or fuse, then restore power.
4. Press the overfill float down and release it so it moves freely.
5. Clean the interior using dishwasher detergent (not household cleansers) and address hard-water film.

Parts that commonly relate to these problems

If the basic checks do not fix it, these model-matched parts are often involved:

Symptom	Common part area	Example model-matched part
Leaks at the door	Door seal	Gasket W11196317
Leaks at vent area	Vent sealing	Dishwasher vent gasket WP8269259
Not draining or water left in tub	Drain path	Dishwasher drain hose 8269144A
No power or dead unit	Electrical protection	Fuse 8193762

Why it matters

A dishwasher that is not latching, not filling, or leaking can lead to incomplete cleaning, longer cycles, and water damage risk. Starting with the latch, power, and float checks prevents unnecessary part replacement.

Last updated: February 2026

If the START button won’t run your Kenmore 66517483300 dishwasher, the most common causes are a door that is not fully latched, the control lock being turned on, or a power interruption. We recommend confirming the correct START/door-closing sequence shown in the 66517483300 owner's manual before replacing parts.

Quick checks that fix most “won’t start” complaints

• Make sure the door is closed tightly and fully latched; the dishwasher will not start if the latch is not engaged.
• If your model has Control Lock, press and hold AIR DRY for 4 seconds to toggle Lock On/Off.
• Press CANCEL, close the door, and let the unit complete the 2-minute drain (if needed), then reselect a cycle.
• Verify the cycle and options are selected, then press START and close the door firmly (top-control models) or close the door firmly and press START (split-control models).
• Check house power: a tripped breaker or blown fuse can leave lights working but prevent operation.

What to inspect if the button still doesn’t respond

If the keypad beeps or lights change but the dishwasher still will not run, focus on the safety interlocks and basic “run” conditions first.

• Door latch/switch: a weak latch or misaligned strike can prevent the control from accepting START.
• Overfill protection float: if it is stuck up, the dishwasher may not fill; press it down to ensure it moves freely.
• Thermal fuse: a blown fuse can stop the control from operating; for this model, check the fuse 8193762.

Symptoms and likely causes

What you see	What it usually means	What to do first
Lock light on or pads flash	Control lock is enabled	Hold AIR DRY 4 seconds
START pressed, nothing happens	Door not latched or latch switch issue	Re-latch door, check latch alignment
Starts then drains and stops	Cycle was canceled or reset needed	Press CANCEL, wait 2 minutes, reselect
Lights on but no run	Power issue or thermal fuse	Check breaker, then test fuse

Why it matters

The dishwasher’s control is designed to ignore START unless the door is latched and the control is unlocked. Confirming those conditions first prevents unnecessary replacement of the control panel, pump, or motor.

Last updated: February 2026