Kenmore 11087879100 dryer Parts

Your Kenmore dryer’s model number is printed on the appliance data label; once you find it, match it exactly (letters and numbers) to look up the correct parts and diagrams. For example, this page is for Kenmore model 11087879100.

Check these common Kenmore dryer locations (look for a sticker or metal plate):

• Inside the door opening on the front panel
• On the door itself (edge or inner surface)
• On the back panel of the dryer cabinet
• Near the lint screen housing (open the lint screen area and look around the frame)
• Behind the lower access panel (some designs place the label low on the cabinet)

Kenmore model numbers are usually a long string of numbers (sometimes with a prefix). Record it exactly as shown.

These steps prevent the most common mix-ups when shopping for Kenmore dryer parts:

• Copy the model number directly from the label, not from the control panel styling
• Include every digit; one missing number can point to a different series
• If your label shows a dot format (example: 110.XXXXXXX), write the full number string too
• Confirm whether your dryer is gas or electric before choosing heating components
• Use the model number to select parts by function (door latch, motor, idler pulley, igniter)

Kenmore dryers share similar looks across many series, but internal components can differ by model. Using the exact model number helps us match the correct diagrams and parts, such as a dryer igniter 279311 for gas-heat symptoms or a dryer idler pulley WP691366 for squealing and belt tension issues.

Last updated: February 2026

For Kenmore dryer model 11087879100, replacing the heating system typically runs $100 to $350 total when you include parts and labor. If you do the repair yourself, the part cost is usually $20 to $100+, depending on whether you’re replacing only the heater or a larger heating assembly.

DIY cost is mostly the part; professional cost is mostly labor and diagnostic time.

These factors most often push the total up or down:

• Gas vs. electric design: gas dryers often involve ignition and burner components; electric dryers focus on the heater circuit.
• What actually failed: a “no heat” complaint can be the heater, but also airflow, controls, or safety devices.
• Service call and diagnosis fees: many shops charge a flat trip/diagnostic fee.
• Extra parts needed: worn drive parts or seals sometimes get replaced while the dryer is open.
• Vent restriction: if the vent is clogged or crushed, heat problems can return quickly.

For this Kenmore model, these parts are often checked during a heat-related diagnosis:

• Dryer igniter 279311 (gas ignition component)
• Dryer valve coil kit 279834 (opens the gas valve when energized)
• Valve 279923 (gas valve assembly)
• Screen W10828351 and dryer lint screen housing foam seal WP339956 (airflow and lint sealing)

A dryer that is not heating is often an airflow or ignition issue, not just a single failed part. Pricing is lowest when you confirm the root cause first, then replace only what’s needed and restore proper venting.

For step-by-step diagnosis ideas, we recommend starting with gas dryer wont heat troubleshooting video.

Last updated: February 2026

Common problems we see with Kenmore dryers (including model 11087879100) are no heat, long dry times, won’t start, drum not turning, and loud squealing or thumping. Most issues trace back to airflow restrictions (lint buildup), normal wear on moving parts, or a failed ignition or motor component.

• Dryer won’t heat (gas models): failed igniter, weak gas valve coils, or a bad gas valve
• Long drying times: clogged lint screen, blocked venting, or lint leaks around the lint duct seal
• Drum won’t turn: worn idler pulley, motor problem, or a drive system issue
• Loud noise: worn support components, pulley wear, or a failing motor
• Door won’t stay closed / won’t start: door catch or strike not engaging

If your symptom matches, these are common replacement parts listed for this model:

• Dryer igniter 279311 for no-heat on gas dryers
• Dryer valve coil kit 279834 for intermittent heat or burner that clicks but won’t stay lit
• Dryer idler pulley WP691366 for squealing and a loose belt feel
• Motor 279827 for humming, no-start, or drum not turning (after confirming power and door switch)
• Dryer door catch WP3389441 or strike 279570 for door-latch problems

• Clean the lint screen and confirm strong airflow at the outside vent hood.
• Inspect the vent duct for kinks, crushing, or heavy lint buildup.
• Listen during a heat call: igniter glow, burner ignition, then steady flame (gas dryers).
• Spin the drum by hand (unplugged): it should turn smoothly without grinding.
• Check the door closure: the catch should “click” and hold firmly.

A dryer that runs with restricted airflow can overheat, shut down on safety devices, and take much longer to dry. Fixing venting and worn drive parts early helps your Kenmore dryer run quieter, dry faster, and reduce repeat breakdowns.

Related help: Kenmore 110 series electronic control model dryer error codes, plus general basics in what are the main parts of a clothes dryer.

Last updated: February 2026