Maytag MSD2572VEB01 refrigerator Parts

A Maytag refrigerator like model MSD2572VEB01 typically lasts 10 to 15 years. With steady maintenance (clean airflow, stable temperatures, and quick repairs when cooling or water issues start), many units reach the upper end of that range.

What affects lifespan the most

The longest-lasting refrigerators usually have consistent airflow and fewer “strain” events on the sealed system (compressor, condenser, evaporator).

• Keep condenser area clean and well ventilated
• Avoid overpacking so air can circulate in both compartments
• Keep door gaskets sealing tightly to prevent long run times
• Replace clogged water filters on schedule to protect the water system
• Address unusual noises, warming temps, or heavy frost early

Maintenance schedule we recommend

Use this as a simple baseline for MSD2572VEB01 side-by-side care.

Task	How often	Why it helps
Clean condenser coils and grille	Every 6 to 12 months	Reduces compressor run time and heat stress
Check door gasket seal	Every 3 to 6 months	Prevents warm air leaks and frost buildup
Replace water filter	About every 6 months	Maintains flow and reduces valve and dispenser issues
Confirm temps (fresh food and freezer)	Monthly	Catches cooling drift early

For model-specific care and troubleshooting steps, follow the MSD2572VEB01 owner's manual.

Parts that commonly impact “how long it lasts”

These parts do not set the lifespan by themselves, but failures here often cause the symptoms that lead to bigger repairs.

• Water system: refrigerator water filter EDR3RXD1, refrigerator water inlet valve WPW10179146
• Cooling airflow: evaporator fan motor, fan blade, condenser airflow
• Defrost system: heater, thermostat, adaptive defrost control board
• Door sealing: door gasket panels and door gasket

Why it matters

A refrigerator that runs longer than normal (dirty coils, air leaks, restricted airflow) puts extra load on the compressor and can shorten overall service life. Simple upkeep helps your Maytag side-by-side stay efficient and reliable.

Last updated: February 2026

To estimate the age of your Maytag refrigerator model MSD2572VEB01, we use the serial number date code: the first letter is the year and the second letter is the month (the date code appears at the end of the serial number). You can find the model and serial label on the inside wall of the fresh food compartment; see the MSD2572VEB01 owner's manual.

Where to find the serial number on MSD2572VEB01

On this Maytag side-by-side refrigerator, the model and serial number are typically on a label inside the refrigerator compartment.

• Open the fresh food (refrigerator) door
• Look on the inside wall near the crisper area or upper side wall
• Write down the full serial number (include all letters and numbers)
• Use the last characters to locate the 2-letter date code

How to decode the 2-letter date code

Maytag uses a 2-letter code at the end of the serial number.

• 1st letter = year (year code)
• 2nd letter = month (month code)
• The remaining digits/letters in the serial number help identify the production sequence

Quick decode checklist

What you need	What to look for	Example (format only)
Serial number ending	Last 2 letters	...XY
Year	1st of the 2 letters	X
Month	2nd of the 2 letters	Y

Why it matters

Knowing the manufacture month and year helps us match the correct Maytag parts and revisions for MSD2572VEB01, especially for common wear items like a refrigerator water filter EDR3RXD1 or an ice maker assembly.

Tips to avoid common mistakes

• Use the serial number, not the model number, to determine age
• Make sure you are reading the last two letters of the serial number (the date code)
• If the label is hard to read, take a clear photo and zoom in to confirm each character

Last updated: February 2026

If your Maytag MSD2572VEB01 refrigerator is not getting cold, the most common causes are airflow problems (dirty condenser coils or a failed evaporator fan), controls being set incorrectly, or a defrost system issue causing frost buildup. Use the checks below, then confirm model-specific steps in the MSD2572VEB01 owner's manual.

Quick checks we recommend first

• Make sure the refrigerator controls are turned on and not set too warm.
• If it is a new installation or was recently unplugged, allow 24 hours to cool completely.
• Verify the outlet has power (test with a lamp) and check the house breaker or fuse.
• Confirm doors are closing fully and not being held open by bins or food packages.
• Listen for the evaporator fan in the freezer; it should run when the compressor is running.

Most likely causes and what to look for

What you notice	Likely cause	What we do next
Freezer is warm and fridge is warm	No cooling or poor heat removal	Clean condenser coils; check condenser fan (if equipped)
Freezer is cold but fridge is warm	Air not moving to fresh food section	Check evaporator fan and air vents for blockage
Frost/ice on freezer back wall	Defrost problem	Check defrost heater, thermostat, and defrost control
Clicking, humming, then stops	Start components or compressor issue	Check start device/capacitor; consider service if persistent

Parts that commonly fix “not cooling” symptoms

These are model-matched parts we often see involved in cooling complaints:

• Refrigerator evaporator fan motor WP2315549 (moves cold air through the freezer and into the fresh food section)
• Refrigerator adaptive defrost control board WPW10366605 (manages defrost cycles)
• Refrigerator heater WP2323198 (melts frost off the evaporator during defrost)
• Refrigerator bi-metal thermostat WPW10225581 (helps control defrost heater operation)
• Refrigerator temperature control WP2315562 (regulates cooling based on temperature setting)

Why it matters

When airflow is restricted or the evaporator is iced over, the freezer may struggle and the refrigerator section often warms first. Cleaning coils and confirming the evaporator fan and defrost system are working prevents food spoilage and reduces compressor run time.

Last updated: February 2026

For the Maytag MSD2572VEB01 side-by-side refrigerator, the exterior dimensions are 69 3/8 inches high, 35 7/8 inches wide, and 33 3/4 inches deep (depth is typically measured without the handle). For clearance and measuring notes, use the MSD2572VEB01 owner's manual.

MSD2572VEB01 dimensions at a glance

Measurement	Size
Height	69 3/8 in.
Width	35 7/8 in.
Depth	33 3/4 in.

How we recommend measuring your refrigerator

Use a tape measure and record each number; measure twice.

• Measure height from the floor to the top of the cabinet (or hinge cover if it sits higher)
• Measure width at the widest point across the front (doors closed)
• Measure depth from the back of the cabinet to the front of the doors (add extra if you include the handle)
• Check door swing space so doors and bins clear nearby walls
• Leave airflow clearance behind and above so the condenser can cool properly

Clearance checklist (common planning items)

What you are planning for	What to allow
Tight hallway or doorway	Compare to width and height; remove doors if needed
Counter-depth look	Depth is usually greater than counters; plan for protrusion
Water line and outlet	Extra space behind the cabinet for connections

Why it matters

Accurate dimensions prevent delivery surprises, door swing interference, and restricted airflow that can cause warm temperatures and higher energy use.

Last updated: February 2026