Kenmore 11062852100 dryer Parts

To hard reset your Kenmore dryer model 11062852100, unplug the power cord (or switch the breaker off) for 1 to 5 minutes, then restore power and try a timed cycle. This clears many temporary control or timer issues, but it will not fix a no-start caused by airflow or a failed safety part.

Hard reset steps (safe and effective)

• Turn the cycle to OFF.
• Unplug the dryer (or turn OFF the dedicated breaker).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door fully and press PUSH TO START.
• Test on a timed, heated cycle (not Air/Fluff).

For model-specific operating steps and cycle settings, use the 11062852100 owner's manual.

If the dryer still will not start after a reset

The manual’s installation checkout points are the fastest way to narrow it down:

• Confirm the controls are set to a running position (not OFF)
• Push the Start button firmly
• Verify the dryer is plugged into a grounded outlet
• Check the electrical supply (breaker/fuses)
• Make sure the door is fully closed (a door switch issue can stop starting)

Quick symptom guide

What you see	Most common cause	What to check first
Nothing happens at all	No power, door switch, start circuit	Outlet/breaker, door closes firmly
Runs but no heat	Heating circuit problem or airflow restriction	Venting, heater circuit
Stops mid-cycle	Overheating protection opening	Lint buildup, crushed/kinked vent

Why it matters

A hard reset is a good first step because it’s fast and safe, but dryers often stop or refuse to start due to overheating from restricted venting. Keeping the vent clear and uncrushed helps prevent nuisance shutdowns and protects key components like thermostats and thermal cut-offs.

Last updated: January 2026

OEM part number 279838 is the dryer heating element used in Kenmore dryer model 11062852100. It is the electric heater that warms the air flowing through the drum so clothes dry properly; confirm installation and wiring details in the 11062852100 owner’s manual.

What part 279838 does

The heating element is the main heat source in an electric dryer. When it fails, the dryer can tumble normally but produce little or no heat.

Common symptoms tied to a bad heating element:

• Dryer runs but does not heat
• Clothes take much longer than normal to dry
• Heat is intermittent (cycles between warm and cool too quickly)
• Burning smell (stop using the dryer and inspect airflow and wiring)

The correct Sears PartsDirect replacement for this model

For Kenmore 11062852100, the matching replacement part is the dryer element 279838.

Item	What it means	Why you care
OEM part number	279838	Identifies the heating element design
Part name	Dryer element	The component that generates heat
Model fit	Kenmore 11062852100	Helps avoid ordering the wrong part

Before replacing the element (quick checks)

A heating problem is often caused by airflow restrictions or a blown safety device.

• Clean the lint screen and check the lint chute for buildup
• Inspect the vent path for kinks, crushed ducting, or heavy lint
• Make sure the dryer is installed with proper exhaust routing (see venting guidance in the manual)
• If the dryer overheated, also check the thermal protection parts such as the dryer thermal cut-off fuse kit 279816

Why it matters

A restricted vent can overheat the heater housing and repeatedly damage heating and safety components. Good airflow helps the dryer heat correctly, dry faster, and reduce nuisance shutdowns.

Last updated: January 2026

On Kenmore dryer model 11062852100, a CE display points to a control-related fault being detected by the dryer’s electronics. We start with a safe power reset and basic input checks (door and start), then follow the model’s troubleshooting guidance in the 11062852100 owner's manual.

What to do first (safe, fast checks)

• Unplug the dryer or switch the breaker off.
• Wait 2 minutes, then restore power and try a normal cycle.
• Confirm the door closes firmly and the drum light turns off when the door shuts.
• Set the timer to a heated cycle and press and hold Push-to-start for 1 full second.
• Verify the dryer is on a dedicated, properly grounded outlet (no extension cord).

Common causes that trigger a CE-type control fault

These issues commonly make a dryer’s control stop the cycle and show a code.

What can cause it	What you may notice	What we check next
Power supply or grounding problem	Random resets, code returns after restart	Confirm correct outlet, breaker, cord, and grounding per manual
Door circuit problem	Stops when door is bumped, won’t start	Test/replace the dryer door switch WP3406107
Timer or start circuit issue	Clicks but won’t run	Verify timer setting and start switch operation

Why it matters

When the dryer senses an abnormal electrical condition or an unreliable safety input (like the door circuit), it can prevent the motor or heater from running to protect the appliance and your home.

When to stop and schedule service

• The code returns immediately after the reset.
• The dryer will not start with the door fully closed.
• The breaker trips, the cord/outlet feels hot, or you smell overheating.

Last updated: January 2026

Your Kenmore dryer model 11062852100 has a 6.5 cu. ft. drum capacity. That is a full-size 29-inch electric dryer capacity, sized for family loads like towels, jeans, and mixed laundry. For operating and installation details, use the 11062852100 owner's manual.

What 6.5 cu. ft. means for everyday loads

A 6.5 cu. ft. drum gives enough tumbling room for airflow, which helps the heater and blower dry evenly.

• Handles larger mixed loads without packing the drum tight
• Helps reduce long dry times caused by restricted airflow
• Supports better wrinkle control because items can tumble freely
• Works best when you avoid filling the drum completely to the top

Quick capacity comparison

Dryer size	Typical capacity	Best for
Compact dryer	3.0 to 4.5 cu. ft.	Apartments, small loads
Full-size dryer (your 11062852100)	6.5 cu. ft.	Family loads, bulky items
Extra-large full-size	7.0+ cu. ft.	Very large loads, comforters

Why it matters

Matching load size to the 6.5 cu. ft. capacity helps your Kenmore dryer heat and vent properly; that improves drying performance and helps protect heating and safety components such as the dryer thermal cut-off fuse kit 279816.

Last updated: January 2026