Kenmore 66513483K902 dishwasher Parts

Yes. We still carry replacement parts for Kenmore dishwashers, including model 66513483K902, and many common repairs use widely available components like drain pumps, heating elements, door seals, and inlet valves. Use your full model number to match the correct part and avoid fit or wiring issues.

Best way to find the right part for 66513483K902

• Match the full model number 66513483K902 (not just “Kenmore 665”).
• Compare the part name and part ID to what you’re replacing.
• Use the exploded views and part lists in the 66513483K902 owner's manual.
• If the issue is a no-heat, no-drain, or no-start symptom, confirm the failure with basic checks before ordering.
• For installation-related items (drain hose routing, clamps, brackets), follow the 66513483K902 installation guide.

Common Kenmore dishwasher parts customers replace

Here are examples of in-stock parts that commonly solve everyday problems:

Symptom	Likely part to check	Example part for this model
Dishes not drying, water not heating	Heating circuit	Dishwasher heating element W10518394
Water won’t drain, standing water	Drain system	Dishwasher drain pump WPW10348269
Leaks at the door	Door sealing surface	Dishwasher door seal W10542314
Won’t fill or fills slowly	Water supply	Dishwasher water inlet valve W10648041

Why model number matching matters

Kenmore dishwashers are built in multiple design families, and parts can look similar but differ in mounting points, electrical connectors, or hose sizes. Using 66513483K902 ensures the correct fit for items like the electronic control board, pump motor, and drain hose.

Quick checks before you order

• No power or dead control: check the house breaker and dishwasher power connection.
• No drain: check for a clogged drain path and a kinked drain hose.
• Poor cleaning: confirm spray arms can spin freely and the filter area is clear.
• Leaks: inspect the door seal for tears, gaps, or debris.

Last updated: February 2026

Your Kenmore dishwasher’s model number is printed on the model and serial number label inside the door area. On Kenmore model 66513483K902, the label is typically on the inner door frame or along the tub opening, and it’s the number you’ll use to match exact parts and troubleshooting info.

Where to look first (fastest checks)

• Open the dishwasher door and inspect the inner door frame (left and right sides).
• Check the top edge of the door and the tub opening lip.
• Look on the tub wall near the front corners.
• Find the label called “model and serial number label” (the manual lists it as a standard feature).
• Write the model number exactly as shown (letters and numbers).

If the label is hard to read

• Wipe the label gently with a damp cloth; grease and detergent film can hide characters.
• Use a flashlight and take a close-up photo; zoom in to confirm each character.
• If the label is damaged, use the serial number on the same label to help confirm the unit.

Why the model number matters

Kenmore dishwashers share many similar-looking racks, pumps, and controls. The exact model number ensures we match the correct fit and electrical specs for items like a heating element, drain pump, or electronic control.

Quick examples of what the model number helps you match

What you’re fixing	What the model number prevents	Example part for this model
No heat or poor drying	Wrong wattage/shape heater	Dishwasher heating element W10518394
Won’t drain	Wrong pump style/connector	Dishwasher drain pump WPW10348269
Leaks at the door	Wrong seal profile/length	Dishwasher door seal W10542314

Helpful references for this model

• Use the diagrams and label location notes in the 66513483K902 owner’s manual.
• If you’re troubleshooting lights or beeps after you identify the model, use Kenmore 665 model dishwasher error codes.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66513483K902 is usually worth it when the problem is a wear item or a single failed part and the repair cost stays well below the price of a replacement; major motor or control failures can tip the decision toward replacing.

Quick decision checklist

• If the dishwasher is under ~10 years old, repairs are typically the better value.
• If the issue is draining, heating, or leaking, a targeted part replacement often restores normal operation.
• If you need a pump motor or electronic control board, compare total repair cost to a new unit.
• If the tub is cracked or the unit has repeated major failures, replacement is usually the smarter spend.
• If performance issues are maintenance-related (odor, poor draining), start with cleaning and setup checks in the 66513483K902 owner's manual.

Common repairs on this model and what they mean

Many “not cleaning” or “not drying” complaints come down to a few serviceable components.

Symptom	Likely area	Example part for 66513483K902	Typical value impact
Water not draining	Drain system	Dishwasher drain pump WPW10348269	Often worth repairing
Dishes not dry	Heating circuit, rinse aid use	Dishwasher heating element W10518394	Often worth repairing
Leaks at the door	Door sealing	Dishwasher door seal W10542314	Often worth repairing
Dead/no power	Power supply, fuse	Fuse W10258275	Often worth repairing
Won’t fill	Water supply/valve	Dishwasher water inlet valve W10648041	Often worth repairing

Why it matters

A dishwasher repair is “worth it” when it fixes the root cause with one visit and one part. For example, the manual notes that poor draining can be caused by a clogged drain air gap (an external plumbing device), so checking that first can prevent unnecessary pump or hose replacement. Use the troubleshooting and cleaning guidance in the 66513483K902 owner's manual to confirm symptoms before buying parts.

Cost comparison rule of thumb

Use this simple guideline to decide quickly:

• Repair when the total repair (parts + labor) is under ~50% of the cost of a comparable new dishwasher.
• Replace when the repair is over ~50% and involves high-cost electronics or major drive components.

Last updated: February 2026

On the Kenmore 66513483K902 dishwasher, an E15 code means the anti-flood protection has detected water in the base area and the dishwasher is trying to prevent an overflow. The fix is to safely remove power, dry the base, then find and correct the leak that put water there.

What to do first (safe reset steps)

• Turn off power at the breaker (or unplug if accessible).
• Shut off the water supply valve under the sink.
• Remove the lower toe/kick plate and look for standing water in the base.
• If water is present, dry it thoroughly (towels or a wet/dry vac).
• Let the unit sit 30 to 60 minutes so moisture around the float switch dries.
• Restore power and run a short rinse to confirm the code clears.

For model-specific safety and access details, follow the steps in the 66513483K902 installation guide.

Common leak sources to check on this model

Most E15 events come from a slow leak that only shows up during fill, wash, or drain.

• Fill leak: check the inlet connection and the dishwasher water inlet valve W10648041
• Door leak: inspect the door perimeter and the dishwasher door seal W10542314
• Drain leak: inspect the drain loop, air gap (if used), and the dishwasher drain hose 8269144A
• Pump area leak: look for drips around the sump and motor area while washing
• Oversuds: too much detergent or non-dishwasher soap can push water past seals

Quick symptom-to-cause guide

What you notice	Most likely cause	What we check
Water at front corners	Door not sealing	Door seal condition, debris on sealing surfaces
Water only during fill	Inlet seep/drip	Inlet valve body, hose clamp tightness
Water near sink cabinet drain	Drain connection leak	Drain hose routing, clamp, air gap
Code returns mid-cycle	Pump/sump leak	Sump area, motor seals, loose fittings

Why it matters

E15 is a flood-prevention shutdown. Clearing the water may reset the dishwasher, but the code will return until the underlying leak (door seal, inlet valve, drain hose, or pump area) is corrected.

If you also see flashing lights or additional codes, use the Kenmore 665 model dishwasher error codes reference to narrow the failure.

Last updated: February 2026

On a Kenmore dishwasher, an E22 code points to a drain or filter restriction that keeps water from moving out normally. On model 66513483K902, the fastest fix is to clean the filter area and check for a blockage in the sump and drain path; then run a rinse cycle.

What to check first (most common causes)

• Turn off power at the breaker before reaching into the sump area.
• Remove the lower rack and look for food, glass, labels, or twist ties around the sump.
• Clean the filter and screen area (if equipped) and rinse debris away.
• Check the drain hose routing for kinks and confirm the high loop/air gap setup matches the installation guide.
• If the unit hums but will not drain, inspect the dishwasher drain pump WPW10348269 for an obstruction.

Quick troubleshooting steps

1. Cancel the cycle and start a drain (or cancel/drain) to see if water evacuates.
2. If standing water remains, clear the sump area and re-test.
3. Verify the sink/disposer connection is open (a clogged disposer inlet or knockout plug can block draining).
4. If draining is slow, check the hose for grease buildup or a pinch behind the cabinet.

Symptoms and likely causes

What you notice	Most likely cause	What to do
Water left in tub, no drain sound	Blocked filter/sump	Clean filter area and sump
Hums but little or no water moves	Drain pump jammed or failing	Clear obstruction; replace pump if needed
Drains sometimes, then errors	Partial hose restriction	Inspect/clean hose and sink connection
Error after heavy soil loads	Food debris overload	Pre-scrape, clean filter area more often

Why it matters

A restricted drain path can leave dirty water in the tub, reduce cleaning performance, and cause repeat error codes. Keeping the filter area and drain route clear helps protect the drain pump and improves wash results.

For model-specific operating and cleaning guidance, use the 66513483K902 owner’s manual.

Last updated: February 2026

On Kenmore dishwasher model 66513483K902, error code F2E2 means the control is not communicating correctly with the user interface (keypad) and the main electronic control. This is typically caused by a stuck key, a loose connection, or a failing control panel or control board.

What to do first (quick checks)

• Press Cancel/Drain once, then wait about 1 minute to see if the code clears.
• Turn power off at the breaker for 2 minutes, then restore power.
• Check for a stuck or wet key on the keypad; wipe the control area dry.
• If the dishwasher recently had a door leak or heavy steam, let it dry out and retry.
• If the code returns immediately, plan on inspecting the control connections.

Likely causes and what they point to

What you notice	Most likely issue	What usually fixes it
Beeping, random button presses, some keys do not respond	Keypad or user interface problem	Replace the control panel/user interface assembly (model-specific)
Code appears after moving the dishwasher or recent service	Loose wire harness connection	Reseat connectors at the UI and main control
Dishwasher powers up but will not start a cycle	UI not sending commands to main control	UI or main control diagnosis
Intermittent code, worsens with heat/steam	Moisture intrusion or failing electronics	Drying, then replace the failing control if it persists

Parts that are commonly involved

On this model, the communication path ultimately relies on the main control. If basic resets and connection checks do not help, the main control is a common next step.

• Dishwasher electronic control board WPW10285179

Why it matters

When the user interface and main control cannot “talk” to each other, the dishwasher may not start, may stop mid-cycle, or may drain unexpectedly. Fixing it early helps prevent repeated cycle failures and protects the electronics from heat and moisture stress.

Reference info for safe access

Follow the safety and access guidance in the 66513483K902 owner's manual before removing panels or handling wiring; disconnect power at the breaker first.

Last updated: February 2026