Kenmore 11020712991 washer Parts

The Kenmore washer model 11020712991 is typically about 3.2 cu. ft. capacity for this 110-series, direct-drive style top-load design. For the exact rated capacity for your specific configuration, confirm it in the 11020712991 owner's manual.

Most owners use capacity as a practical loading guide rather than a strict number. For a 3.2 cu. ft. top-load washer like the Kenmore 11020712991, we recommend:

• Load clothes loosely; do not pack them down
• Keep items below the top of the basket so the agitator can circulate the load
• Wash bulky items (comforters, jackets) one at a time when possible
• Balance mixed loads (towels with towels, jeans with jeans) to reduce vibration
• Use the correct water level and cycle for the fabric type

Capacity is the volume of the wash basket, not a guarantee that every load should be filled to the top.

Using the right load size helps the washer agitate, drain, and spin correctly. Overloading is a common cause of poor cleaning, long drain times, and extra wear on drive components such as the coupling 285753A and washer drain pump WP3363394.

Last updated: February 2026

Your Kenmore washer model number is printed on the model and serial number plate; on model 11020712991, it’s the ID you’ll use to match the correct washer parts (like a lid switch, drain pump, or inlet valve) and the right troubleshooting steps. Use the 11020712991 owner's manual to confirm the exact plate location and how the number is formatted.

On Kenmore washers, the model and serial number plate is typically placed where it stays readable but protected from bumps and water. Check these common spots first:

• Under the lid, around the tub opening (top-load washers)
• Along the rim of the lid opening, near the hinge area
• On the back panel near the power cord entry
• Behind the control panel area (varies by design)
• Inside the cabinet on a side wall (visible when the lid is open)

Kenmore model numbers often start with 110 and are usually 11 characters or longer. The full model number is what we use to ensure part compatibility.

• Copy the number exactly as printed (include all digits)
• Take a clear photo of the plate for reference
• Write down both model and serial numbers for future repairs
• Use the full model number when ordering common wear items

Small design changes can affect fit and wiring. Using the exact model number helps us match the correct replacement parts for your Kenmore washer, such as the washer lid switch WP3949238 or washer drain pump WP3363394, and reduces returns due to incompatibility.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore washer when the fix restores reliable washing and spinning for far less than replacing the machine. For Kenmore model 11020712991, common wear items (like the lid switch, drain pump, or motor coupling) are often straightforward repairs that can extend service life.

Use this checklist before you spend money on parts or labor:

• The washer still fills, agitates, or drains sometimes (intermittent problems are often a single failed part).
• The cabinet and tub are in good shape (no severe rust-through or major leaks).
• The repair is a common failure item (lid switch, pump, coupling, clutch).
• The cost of parts plus labor is comfortably below the cost of a comparable new washer.
• You want to keep a familiar, simple mechanical washer design.

These are frequent fixes on direct-drive Kenmore top-load washers and typically deliver a long-lasting improvement:

We recommend these steps before ordering parts:

• Confirm the washer is level and the front leg nuts are tight; an unlevel washer can vibrate and act “worse than broken.”
• Verify the lid closes firmly and the lid strike aligns with the switch.
• Check for a kinked or restricted drain hose and a clogged pump inlet.
• Listen for motor sound: running motor with no movement often points to a coupling or drive issue.
• Use the troubleshooting section in the 11020712991 owner’s manual to match symptoms to likely causes.

A targeted repair keeps a dependable washer in service, avoids the learning curve of a new machine, and often fixes the exact failure point (instead of replacing an entire appliance for one worn component).

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11020712991, good installation and routine care (leveling, avoiding overloads, and using the right cycle) help you reach the high end of that range; see the 11020712991 owner's manual for care and operating guidance.

Most top-load washers like this Kenmore are built for years of dependable operation, but lifespan depends heavily on load size, water quality, and how well the machine is kept level.

• Overloading strains the drive system and suspension
• Unbalanced loads increase vibration and wear
• Hard water can shorten valve and pump life
• Poor leveling causes repeated shaking and cabinet stress
• Skipped maintenance leads to clogs, odors, and leaks

When a washer starts to fail early, it is usually one of a few wear items. These are common on direct-drive style Kenmore washers.

These habits reduce stress on the motor, gear case, clutch, and basket.

• Keep loads below the top of the basket and distribute items evenly
• Do not wrap items around the agitator (helps prevent tangling and strain)
• Use the correct water level and cycle for the fabric type
• Confirm the washer is level and the front leg nuts are tight (reduces vibration)
• Periodically check hoses and the drain path for kinks or restrictions

A washer that is level, correctly loaded, and operated as intended runs smoother, wears parts more slowly, and is less likely to develop leaks or spin problems that shorten overall lifespan.

Last updated: February 2026