Kenmore Elite 66513923K012 undercounter dishwasher Parts

Yes. We still support replacement parts for many Kenmore dishwashers, including Kenmore Elite model 66513923K012. The key is matching parts by the full model number so you get the correct fit for common repairs like draining issues, leaks, rack problems, and filling problems; start with the 66513923K012 owner's manual.

How to make sure you order the right part

Use the model number 66513923K012 (from the rating label) and then match the part by name and ID.

• Confirm the full model number and revision (the suffix matters)
• Compare the part name and part ID, not just a photo
• Check where the part installs (upper rack, lower rack, door, sump area)
• If your symptom is intermittent, inspect wiring and connectors before replacing parts
• For installation requirements and clearances, reference the 66513923K012 installation guide

Common Kenmore Elite 66513923K012 parts customers replace

These are frequent wear items and failure points on undercounter dishwashers.

Symptom	Likely part to check	Example part for this model
Lower rack won’t roll smoothly	Rack wheels/rollers	Dishwasher dishrack roller assembly, lower WPW10195417
Dishwasher won’t drain or drains slowly	Drain pump or drain hose	Dishwasher drain pump WPW10348269
Not filling or fills too slowly	Water inlet valve	Dishwasher water inlet valve W11175771
Leaks at the bottom of the door	Lower door seal	Seal WPW10497235
Poor drying or water not heating	Heater	Dishwasher heater W10703867

Why it matters

Kenmore dishwashers are often built by major manufacturers, so parts availability stays strong, but the exact configuration can vary by model and revision. Using 66513923K012 prevents ordering a look-alike part that does not mount correctly or connect to your harness.

Last updated: February 2026

On Kenmore Elite dishwasher model 66513923K012, the most reliable “hard reset” is to cancel the current cycle and reset the control: press CANCEL/DRAIN twice, then select a new cycle and press START/RESUME. For the exact button sequence for your console, use the 66513923K012 owner's manual.

Quick reset steps (control reset)

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Press CANCEL/DRAIN once, then press CANCEL/DRAIN a second time (this resets the control).
• Close the door within about 3 seconds so the unit can drain if needed.
• Select your new cycle and options.
• Press START/RESUME, then close the door within about 3 seconds to begin.

If the dishwasher is unresponsive

These steps help when the keypad seems “stuck” or the cycle will not start.

• Make sure the door is fully latched (a loose latch can prevent starting).
• Press START/RESUME again if the door was opened mid-cycle.
• If option lights flash, reselect a valid option for the chosen cycle.
• Turn the sound on or off (some models): press and hold HIGH TEMP for 3 seconds.
• If it still will not respond, shut off power at the breaker for 1 minute, then restore power and try the control reset again.

What to expect after you reset

Action	What you should see/hear	Typical time
CANCEL/DRAIN pressed	Cancel/Drain light turns on	Immediate
Door closed after cancel	Unit drains if water is present	Up to ~2 minutes
START/RESUME pressed	Cycle begins when door is closed promptly	Within seconds

Why it matters

Resetting the control clears a stalled cycle and gets the dishwasher back to a known starting point. It also prevents repeated start failures caused by an interrupted cycle that needs START/RESUME pressed again.

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end line, and the Kenmore Elite dishwasher model 66513923K012 is built to deliver upgraded features and a more premium fit and finish than basic Kenmore models. Exact feature sets vary by model, so we recommend confirming the options and cycle details in the 66513923K012 use and care guide.

What “high end” means for Kenmore Elite dishwashers

In our experience, “high end” typically shows up as better cleaning systems, quieter operation, and more refined rack and control designs.

Common Kenmore Elite advantages include:

• More wash cycle choices and targeted options (heavy, quick, sanitize, etc.)
• Improved filtration and soil handling (less redeposit on dishes)
• Better rack adjustability and smoother rack movement
• More robust drying performance (often tied to a heater and venting design)
• More premium exterior and control styling

How to judge if your specific model is “high end”

Use this quick checklist for model 66513923K012:

• Compare cycle list and options in the manual to what you actually use
• Check rack condition and glide performance; worn rollers can make a premium unit feel “cheap”
• Confirm drying system performance; poor drying can be a setup, loading, or heating issue
• Look for consistent fill and wash action; weak wash can point to a water supply or circulation issue

Quick comparison (typical positioning)

Line	Typical positioning	What you usually get
Kenmore (standard)	Value to mid-range	Core cycles, basic racks, fewer upgrades
Kenmore Elite	Mid-to-high end	More features, better racks, quieter designs
Boutique “luxury” brands	Premium	Specialized features, higher price point

Why it matters

Knowing the product tier helps you decide whether to repair or upgrade. A Kenmore Elite dishwasher is usually worth maintaining because many performance issues are solved with targeted part replacements and proper installation.

If your door feels heavy or drops quickly, a worn balance system can affect day-to-day usability; the dishwasher door balance link 8194001 is a common wear item on many designs.

Last updated: February 2026

Yes, repairing a Kenmore Elite dishwasher like model 66513923K012 is usually worth it when the fix is a common wear item (racks, seals, hoses, valves, pumps) and the total repair cost stays well below the price of a replacement. Use the 66513923K012 owner's manual to match symptoms to the right repair.

Quick rule of thumb (repair vs replace)

• Repair when the problem is a leak, drain issue, poor cleaning, or rack hardware failure.
• Repair when the dishwasher is in good overall condition (quiet motor, solid tub, no repeated failures).
• Replace when multiple major systems are failing at once (controls plus motor/pump plus leaks).
• Replace when the tub is damaged or the unit has chronic electrical issues.

Common repairs that are typically worth it

These are frequent, targeted fixes on undercounter dishwashers and usually restore performance quickly:

• Drain problems: check the drain path and consider a drain pump such as dishwasher drain pump WPW10348269.
• Leaks at the bottom of the door: inspect the lower door seal such as seal WPW10497235.
• Not filling or filling slowly: verify water supply and consider the dishwasher water inlet valve W11175771.
• Poor drying: heating circuit issues can involve the dishwasher heater W10703867.
• Rack issues (wheels, stops, rails): worn rack hardware can be fixed with parts like dishwasher dishrack roller assembly, lower WPW10195417.

Cost and effort comparison

Situation	Typical best choice	Why
One failed part (pump, valve, seal, rack hardware)	Repair	Lower cost, limited labor, predictable outcome
Two or more major parts failing together	Compare totals	Costs add up quickly
Installation-related issues (hoses, clearances, freezing risk)	Repair plus correct install	Prevents repeat failures

Why it matters

A focused repair keeps your Kenmore Elite undercounter dishwasher running reliably and avoids repeat problems. The installation instructions also stress basics that prevent damage, such as keeping lines and wiring from contacting moving parts and protecting the dishwasher and water lines from freezing; those steps can make a repair last longer.

Last updated: February 2026

For Kenmore Elite dishwasher model 66513923K012, the key “dimensions” most installers need are the cabinet opening requirements: 23 7/8 in. minimum width, 24 in. depth, and 33 7/8 in. height from the floor to the underside of the countertop. See the 66513923K012 installation guide for exact fit details.

What to measure before you buy or install

Measure the opening and the path to the kitchen, then compare to the installation requirements.

• Opening width at the front and back: 23 7/8 in. minimum
• Opening depth: 24 in.
• Opening height (floor to underside of countertop): 33 7/8 in.
• Confirm the unit can slide in without pinching the drain hose, water line, or wiring
• Verify the dishwasher can be leveled so the door aligns evenly with the tub

Quick reference table

Measurement	What it means	Target for 66513923K012
Width	Cabinet opening side-to-side	23 7/8 in. minimum
Depth	Cabinet opening front-to-back	24 in.
Height	Floor to underside of countertop	33 7/8 in.

Why it matters

Correct opening dimensions prevent installation problems like door rubbing, poor leveling, and interference with plumbing or electrical routing. A proper fit also helps the dishwasher stay secured so it does not tip when the door is opened.

Last updated: February 2026

A Kenmore Elite undercounter dishwasher like model 66513923K012 typically lasts 10 years with normal use and basic maintenance. Keeping the filter and spray system clean, fixing leaks quickly, and using the right detergent helps you reach (and often exceed) that expected service life.

Typical lifespan and what affects it

Most dishwashers fall into a similar life range, but real-world lifespan depends on usage and care.

• Loads per week: more cycles usually means faster wear on pumps, seals, and racks
• Water quality: hard water can leave mineral buildup on the heater and internal passages
• Cleaning habits: a clogged filter or spray arm reduces wash performance and strains the motor
• Leak exposure: even small leaks can damage wiring and controls over time
• Installation conditions: proper clearances and routing of lines prevents rubbing, kinks, and vibration issues (see the 66513923K012 installation guide)

Maintenance that extends life (high impact)

Use these as a simple routine for Kenmore Elite dishwashers:

• Rinse heavy food off dishes and avoid bones, seeds, and labels entering the sump
• Clean the filter regularly; replace it if it is cracked or won’t clean up well (see dishwasher filter W10872845)
• Check the spray arms for blocked jets and remove debris
• Use rinse aid and the correct detergent amount to reduce residue
• Inspect the door sealing surfaces and wipe them clean

Quick “replace vs. repair” guide

What you’re seeing	Most common cause	Usually worth repairing?
Not draining	Drain pump or drain hose restriction	Yes
Poor drying	Heater issue, rinse aid, or airflow/venting	Yes
Door won’t stay up	Door balance link/hinge wear	Yes
Rusting racks	Rack coating failure	Sometimes

Why it matters

Knowing the expected lifespan helps you decide when a repair (like a drain pump, heater, or door balance part) is a smart investment versus when overall wear makes replacement the better value. For model-specific care and cleaning steps, use the 66513923K012 owner’s manual.

Last updated: February 2026

Your Kenmore Elite dishwasher model number is printed on the rating label inside the door. On model 66513923K012, we look just inside the dishwasher door opening (typically along the left side) for a label that lists both the model and serial number; confirm the format in the 66513923K012 owner's manual.

Where to find the model number label

Check these common spots on Kenmore Elite undercounter dishwashers:

• Inside the door opening on the left side of the tub frame
• Along the inner edge of the door (visible when the door is open)
• Near the top or side of the door liner area
• On a paper or metallic rating plate with safety and electrical information

What to write down (and why)

Record the model number exactly as shown (letters and numbers). We use it to match the correct Kenmore parts, diagrams, and installation requirements.

• Model number (example format: 66513923K012)
• Serial number (helps identify production run)
• Any suffixes or revision codes printed with the model

Quick ID checklist

Item	What it’s used for	Example
Model number	Correct part fit and diagrams	66513923K012
Serial number	Version and production details	Varies

If the label is hard to read

Use a flashlight and wipe the area with a damp cloth; detergent residue can hide the print.

• Open the door fully and look along the tub frame edge
• Clean the label gently (do not scrape)
• Take a clear photo and zoom in to read it

Why it matters

Kenmore Elite dishwashers can look similar across multiple 665-series models, but parts like the water inlet valve, drain pump, and racks can differ. Using the exact model number prevents ordering the wrong replacement part.

Last updated: February 2026

If the START/RESUME button on your Kenmore 66513923K012 won’t start a cycle, the usual causes are Control Lock being on or the door not being latched and closed within 3 seconds after pressing START/RESUME. Restore normal operation with the checks below.

Quick checks that fix most “won’t start” issues

• Turn off Control Lock: press and hold CONTROL LOCK for 3 seconds until the lock light turns off.
• Press START/RESUME, then close the door within 3 seconds; waiting longer prevents the cycle from starting.
• If the door was opened mid-cycle (even to add a dish), press START/RESUME again and close the door within 3 seconds.
• Cancel and restart the cycle (use Cancel/Drain if your control has it), then reselect the cycle.
• Reset power: switch the dishwasher off at the breaker for 5 minutes, then restore power and try again.

Match the symptom to the likely cause

What you notice	Most likely cause	What to do
Lock light on; buttons beep or don’t respond	Control lock enabled	Hold CONTROL LOCK 3 seconds
Start light flashes; tones sound	Door not closed in time or not latched	Re-press START/RESUME; firmly close door
Lights work but wash never begins	Latch not engaging or door switch not sensing closure	Check latch area; close door firmly
Unit drains but won’t wash	Cycle canceled or control needs reset	Power reset; start a normal cycle

Door closing and latch checks

• Remove items that keep the door from closing squarely.
• Clean detergent buildup around the latch and strike.
• Confirm the dishwasher is level; a shifted tub can affect latching.

Why it matters

This model requires a confirmed door latch for safety; if the door is opened or not closed quickly after pressing START/RESUME, the control blocks the start.

For Control Lock and START/RESUME timing details, use the 66513923K012 owner's manual.

Last updated: February 2026

A small amount of water in the bottom of your Kenmore Elite dishwasher model 66513923K012 can be normal between cycles, but standing water that never drains usually points to a drain restriction (filter, hose, disposer connection) or a failing drain pump. Use the built-in Cancel/Drain function first, then check the drain path.

Quick checks we recommend first

• Run CANCEL/DRAIN and let it finish (about 2 minutes) as described in the 66513923K012 owner's manual.
• If your dishwasher drains into a food waste disposer, confirm the disposer inlet knockout plug was removed.
• Inspect the drain hose for kinks, crushing, or a low spot that traps water.
• Clean the bottom-center filter area; filters need periodic cleaning to keep performance up.
• Listen during drain: a humming sound with little or no water movement often indicates a jammed or weak pump.

Most common causes and what to do

What you see	Likely cause	What to do next
Water remains after Cancel/Drain	Clogged filter or drain path	Clean filter area; clear hose/disposer blockage
Hums but does not drain	Drain pump obstruction or failure	Check for debris; replace pump if needed
Drains slowly	Partial blockage or kinked hose	Re-route/clear hose; verify disposer connection
Water returns after draining	Backflow from sink/disposer	Check hose routing and connection; avoid sags

Parts that commonly fix a no-drain issue

If the drain path is clear and the unit still will not pump out, the drain pump is a common repair on this model.

• Dishwasher drain pump WPW10348269: pumps water out through the drain hose.
• Dishwasher drain hose 8269144A: a damaged or restricted hose can prevent proper draining.
• Dishwasher filter W10872845: a clogged filter can slow drainage and leave water behind.

Why it matters

Standing water can cause odors, poor cleaning, and can keep detergent from rinsing away properly. Restoring normal drainage protects the sump area, improves wash performance, and helps prevent repeat clogs.

Last updated: February 2026