Kenmore Elite 79047883604 electric oven Parts

Kenmore is a brand sold by Sears; the Kenmore Elite wall oven model 79047883604 is part of the 790-series that is widely associated with Frigidaire/Electrolux-built ovens. For model-specific identification details (model/serial plate location and documentation), use the owner's manual.

We confirm the builder by matching the model prefix and the data on the serial plate.

• Check the model number format: 790 is the key identifier for this Kenmore Elite wall oven family.
• Locate the serial plate and record the full model and serial.
• Compare the recorded information to the documentation for your unit.
• Use the parts list for your model to see common OEM part families used on this platform.

The Use & Care Guide includes a section for serial plate location.

Knowing the original manufacturer helps you choose compatible replacement parts (for example, heating and temperature-sensing components) and follow the correct service procedures for a Kenmore Elite electric wall oven.

Last updated: February 2026

To reset your Kenmore Elite wall oven model 79047883604, clear the control first (STOP/CLEAR), then restore power by turning the breaker off and back on; after power returns, set the clock and reprogram cooking functions as needed. See the reset and power-failure notes in the owner's manual.

• Press STOP/CLEAR once to cancel a cooking cycle and clear most beeping or fault displays.
• If the control is still unresponsive, turn the oven circuit breaker OFF for 1 to 5 minutes.
• Turn the breaker ON.
• Set the clock; the oven will not program correctly until the time is set after an interruption.
• Try Bake again and confirm the oven heats normally.

The manual’s “Before you call” section recommends clearing the alarm first, then checking whether the fault returns.

If the oven won’t start but the control works, the Oven Lockout feature may be enabled. Hold the lockout pad for 3 seconds to return to normal operation (the door unlocks and the oven becomes operational again).

A proper reset protects the electronic control and prevents the oven from restarting unexpectedly after a power interruption. It also gets the control back into a programmable state (clock set, functions cleared).

Last updated: February 2026

For the Kenmore Elite wall oven model 79047883604, the installation guide shows two common size classes: 27-inch and 30-inch wall ovens. The overall product dimensions depend on which size class your specific unit is; use the dimension chart in the installation guide to match your oven to the correct measurements.

The installation guide lists these overall product dimensions (not cabinet cutout):

• 27-inch wall oven: approximately 27 in wide, 24 7/8 in high, and 24 5/8 in deep
• 30-inch wall oven: approximately 30 in wide, 28 1/4 in high, and 24 1/2 in deep
• For double-oven configurations, the guide shows an overall height around 50 1/2 in (width and depth still follow the 27-inch or 30-inch class)

Because the guide covers both 27-inch and 30-inch versions, we recommend matching your oven to the correct class using one of these checks:

• Measure the front frame width (left to right across the face)
• Compare your measurements to the 27-inch vs 30-inch chart in the guide
• Confirm whether you have a single oven or double oven setup
• If you are measuring for cabinetry, use the cutout dimensions section (different from product dimensions)

Using the correct size class prevents fit issues and helps avoid installation problems like insufficient clearance, misaligned trim, or heat buildup from a tight cabinet opening. The installation guide also calls out clearance needs (such as space in front of the door) and support requirements.

Last updated: February 2026

PF on a Kenmore Elite wall oven model 79047883604 means power failure. It shows up after the oven is first powered on or when electrical power is interrupted; the display flashes “PF” until you clear it and reset the clock using the steps in the owner's manual.

• Press STOP/CLEAR to clear the PF message.
• Set the clock (the oven may not program correctly until the time is set).
• If the display returns to normal, test Bake at 350°F for a few minutes.
• If PF keeps coming back, check for a loose plug, tripped breaker, or a flickering circuit.
• If the control beeps and shows an F code after a power event, press STOP/CLEAR to stop the beeping and clear the code.

PF is not a cooking-mode failure by itself; it is the oven telling you it lost power. Clearing PF and resetting the clock restores normal operation, and repeated PF events point to a power supply problem that can also damage electronic controls over time.

If you find signs of overheating or looseness at the power connection (power off at the breaker first), the connection hardware is a common fix area:

• Terminal block 5304409888 (power connection point)
• Wiring harness 318370303 (if wiring is damaged)

Last updated: February 2026