Kenmore Elite 66513193K902 dishwasher Parts

Your Kenmore Elite 66513193K902 is a dishwasher model, not a washer; dishwasher capacity is measured by place settings (and rack layout), not cubic feet. For the correct capacity and loading guidance for this specific Kenmore Elite dishwasher, use the 66513193K902 owner's manual.

We size dishwashers by how many place settings they hold and how the upper and lower racks are configured.

• Count place settings you can load comfortably without blocking the spray arms
• Keep tall items from preventing the upper spray arm from turning
• Avoid nesting bowls and spoons that trap water and detergent
• Load plastics securely so they do not flip and fill with water
• Keep the filter area clear so wash water circulates properly

Using the correct capacity measure helps you load the Kenmore Elite 66513193K902 so water flow and detergent coverage stay strong. Overloading or blocking spray paths is a top cause of poor cleaning, spotting, and leftover debris.

The most reliable place is the model-specific documentation:

• Look for “capacity” or “place settings” in the specifications section
• Use the loading diagrams for the upper rack, lower rack, and silverware basket
• Follow detergent and rinse aid recommendations for your water hardness

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s high-end line, and the Kenmore Elite dishwasher model 66513193K902 is built around premium construction and ownership features such as stronger warranty coverage (including stainless tub leak-through coverage on stainless tub models) compared with typical entry-level dishwashers; see the 66513193K902 owner’s manual for the exact coverage and feature set.

High-end positioning usually shows up in a mix of build quality, features, and long-term support.

• Warranty depth: The manual describes multi-year coverage, including rack coverage and stainless tub leak-through coverage on stainless tub models.
• Installation requirements: The installation guide calls out clearances and protection steps (for example, keeping lines away from the motor and not installing over carpet).
• Serviceable design: Common wear and repair items are replaceable, such as a drain pump, inlet valve, and control board.
• Premium fit and finish: Many Elite models include upgraded handles and panels; some handle kits are installed during setup.
• Performance depends on upkeep: Like any dishwasher, cleaning the filter and keeping spray arms clear has a direct impact on wash results.

If cleaning results or draining performance slip, these are frequent check points on model 66513193K902:

• Dishwasher filter W10872845 (clogging can reduce wash performance)
• Dishwasher spray arm WPW10491331 (blocked jets reduce coverage)
• Dishwasher drain pump WPW10348269 (weak draining can leave water behind)
• Dishwasher water inlet valve W10648041 (low fill can cause poor cleaning)
• Dishwasher electronic control board WPW10285178 (cycle and option control)

“High end” is most noticeable in day-to-day ownership: quieter operation, better cleaning consistency when maintained, and stronger warranty support. For the exact features and care steps that keep this Elite dishwasher performing at its best, use the 66513193K902 installation guide alongside the owner’s manual.

Last updated: February 2026

For Kenmore Elite dishwasher model 66513193K902, the installation opening is 23 7/8 inches wide, 24 inches deep, and 33 7/8 inches high (floor to underside of countertop). Use these measurements to confirm the cabinet cutout and leveling clearance before installation; see the 66513193K902 installation guide.

• Opening width: 23 7/8 in.
• Opening depth: 24 in.
• Opening height: 33 7/8 in. (floor to top of opening)
• Clearance note: keep space so the motor and leveling legs do not contact the floor
• Routing note: keep drain, water, and wiring from rubbing the motor or legs

Dishwashers are designed to be leveled in the opening. If the opening is too tight or the floor is uneven, the unit can sit twisted, which leads to door alignment issues, vibration, and poor draining.

• Do not install over carpeted flooring.
• Protect the dishwasher and water lines from freezing.
• Route the drain hose and water line so they do not contact moving parts.
• Confirm the unit can be leveled without the motor touching the floor.

For operating clearances and feature details (rack setup, cycles, filtration), use the 66513193K902 owner’s manual.

Last updated: February 2026

A Kenmore Elite dishwasher typically lasts 10 years under normal household use. For model 66513193K902, lifespan depends most on routine cleaning, correct installation clearances, and preventing leaks and drain problems; our maintenance steps below help you reach that 10-year mark.

• Filter and sump cleanliness; reduces pump strain and wash issues
• Drain performance; standing water shortens component life
• Water quality and detergent use; hard water and excess detergent increase buildup
• Door sealing and venting; helps prevent moisture damage around the door
• Rack condition; rust and broken coating can spread and damage dishes

Use these habits to extend the life of your Kenmore Elite 66513193K902:

• Clean the filter area regularly and remove debris after heavy loads
• Run hot water at the sink before starting a cycle for better wash performance
• Keep spray arm holes clear; remove labels, seeds, and glass fragments
• Inspect the door seal area and wipe it clean to prevent leaks
• Make sure the unit is installed with proper clearance so the motor does not contact the floor (installation detail)

Most dishwashers get replaced because of recurring drain, leak, or wash-performance problems, not because the tub “wears out.” Staying ahead of clogs and leaks protects high-wear components like the pump and motor assembly.

For cycle and care guidance specific to this unit, follow the maintenance and operating recommendations in the 66513193K902 owner’s manual.

Last updated: February 2026

Your Kenmore Elite dishwasher model number is printed on the rating label inside the door area. On Kenmore Elite dishwashers like model 66513193K902, the label is typically on the inner edge of the door opening (often along the left side) and lists both the model and serial number.

Check these common spots first (with the door open):

• Inner left side of the tub frame (door opening edge)
• Inner right side of the tub frame (less common)
• Along the top edge of the door or tub opening
• Behind the toe kick area (rare on this style)

If the label is dirty or faded, wipe it gently with a damp cloth and a little mild dish soap.

Kenmore Elite dishwasher model numbers are a mix of numbers and letters. For this page, the model format is:

We use the exact model number to match the correct Kenmore parts, including items that can vary by production run such as the control panel, pump and motor assembly, and door hardware. Using the full model number prevents ordering the wrong drain hose, spray arm, or rack parts.

Once you locate the label, compare it character-for-character to ensure you have the full model number:

• Write it down exactly as shown (including any ending letters)
• Use it when selecting parts like the dishwasher drain pump WPW10348269
• Keep a photo of the label for future repairs
• For diagrams and identification help, use the 66513193K902 owner's manual

Last updated: February 2026

Kenmore Elite dishwasher model 66513193K902 was manufactured by Whirlpool. Kenmore is the brand name; the 665 model prefix is the key identifier that points to Whirlpool as the original maker for many Kenmore dishwashers.

Kenmore uses a model-number prefix system that indicates who built the appliance.

• Look at the first three digits of the model number (the prefix)
• 665 prefixes are Whirlpool-built dishwashers
• Other Kenmore prefixes can indicate other manufacturers (varies by product line)
• The rest of the model number helps identify the exact series, features, and configuration

Knowing Whirlpool built your Kenmore Elite 66513193K902 helps when you are matching parts, troubleshooting symptoms, or comparing diagrams.

If you are diagnosing a problem or planning a repair, we recommend starting with the documentation and then checking the most common service parts.

• Confirm the full model number on the rating label matches 66513193K902
• Use the 66513193K902 owner’s manual to verify features and operating details
• Use the 66513193K902 installation guide for hookup and clearance requirements
• For draining issues, check the dishwasher drain pump WPW10348269 and drain hose routing
• For poor cleaning, inspect and clean the filter and spray arm (common maintenance items)

The correct manufacturer match reduces wrong-part returns and speeds up repairs because the internal design and part numbering typically follow the original builder’s platform.

Last updated: February 2026